Reviews
Fits: HONDA CBR250RR(2017-), HONDA CBR250RR(2017-)
Can be installed without any problem
It is always better to be cheap in order to comply with Race's Regulation. View detail
Fits: HONDA CBR250RR(2017-), HONDA CBR250RR(2017-)
Low price and quality
Installed on a vehicle competing in the CBR250RR DREAMCup.
Workability
Anyone can do it, just tighten one Bolt of m8.
If anything, it is a good idea to check for interference with the Wiring and Brake hose after installation.
Effects
The cutting angle can be reduced considerably.
Since it is a Racer, it must ensure Clearance with Cowl, Tank, etc. in terms of Regulation.
But when I adjust the Handlebar angle, lever position, etc., the MC51 immediately hits somewhere.
If you change the exterior to a race cowl, it's a little better, but you still have to cut it until it hits the stopper, and then you can cut it to the Upper or Tank.
It interferes immediately.
The advantage of attaching this product is that it can be adjusted without worrying about such interference.
I don't think this is a product that requires any other advantages.
Costco
Best. I bought it because it was the cheapest.
I am satisfied with the price, especially since there were no problems with the installation.
View detail
Fits: HONDA CB250F, HONDA Forza Si, HONDA PCX125, HONDA ZOOMERX, HONDA CB600RR, HONDA CB400F, HONDA CBR400R, KAWASAKI NINJA250R, HONDA CB650F, HONDA CBR650F, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CB1100, HONDA CB400SUPER BOLDOR, HONDA CB400SF, HONDA 400X, HONDA VTR250, HONDA VTR-F, HONDA CBR250R (2011-), HONDA CBR250R (2011-)
ENDURANCE Master Cylinder Holder B
Excellent quality and durability!!! this pieces are well made to last. They give a great handlebar view and the looks is very outstanding from the original piece. View detail
Good for color Accent
Since Z125PRO SE is only Black when viewed from the top, I chose Blue's Color.
It is good feeling that Color is Accent ♪
View detail
Fits: HONDA CB250F, HONDA Forza Si, HONDA PCX125, HONDA ZOOMERX, HONDA CB600RR, HONDA CB400F, HONDA CBR400R, KAWASAKI NINJA250R, HONDA CB650F, HONDA CBR650F, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CB1100, HONDA CB400SUPER BOLDOR, HONDA CB400SF, HONDA 400X, HONDA VTR250, HONDA VTR-F, HONDA CBR250R (2011-), HONDA CBR250R (2011-)
Used as mounting base for Fog Lamp switch
【What made you decide the purchase?】
- table (Front) The surface is flat
【How was it actually used?】
I use it as a mount base for fog Lamp switch.
Since the surface was flat, I could install the Switch without problems.
Because NORMAL's master Cylinder Holder has a curved surface, we are exchanging it with this Holder.
By the way, Switch is amon's "Lock fastener" (http : / / www. webike. net / sd / 1353473 / We are installing it using.
【Mounting was difficult?】
Installation was not particularly difficult.
【Please tell me the installation point and hang】
The vertical direction of the Holder is fixed when installing it, but usually it is as understood by the logo mark of the surface.
Since this logo mark is hidden by Magic tape this time, I wrote the arrow on the back side with Magic so that you can see the direction of the top and bottom.
[Is there anything I was disappointed about?]
Although it is not about disappointment, although the same Black has its color tone different from that of the master Cylinder, there are times when it is worrisome (See the posted photo).
【Hope for Manufacturer - Please let me know if you have any improvement points]
As of now, nothing special.
【Have you compared items?】
- ENDURANCE : Master Cylinder Holder Kit
(http : / / www. webike. net / sd / 21853260 / )
Products of this impule Holder 1 pc. Although it is only here, Quantity : 1 Set of 2pcs. It will be.
The Clutch side hid in the Antennas integral type ETC and is inconspicuous so we stopped exchanging the Clutch lever Holder.
[Others]
PIAA's Fog Lamp (http : / / imp. webike. net / commu / diary / 0125602 / ) Included a Switch bracket for attaching the Handlebar, but using Bracket to attach a Switch to the Brake side will interfere with the Master Cylinder.
Therefore, Switch is attached to Master CylinderHolder.
* "The 5th Impression Con test" (http : / / campaign. webike. net / 2016 / 03 / 20160318_impression_contest / I'm applying to.
View detail