Reviews
Fits: HONDA CBR250RR(2017-), HONDA CBR250RR(2017-)
Low price and quality
Installed on a vehicle competing in the CBR250RR DREAMCup.
Workability
Anyone can do it, just tighten one Bolt of m8.
If anything, it is a good idea to check for interference with the Wiring and Brake hose after installation.
Effects
The cutting angle can be reduced considerably.
Since it is a Racer, it must ensure Clearance with Cowl, Tank, etc. in terms of Regulation.
But when I adjust the Handlebar angle, lever position, etc., the MC51 immediately hits somewhere.
If you change the exterior to a race cowl, it's a little better, but you still have to cut it until it hits the stopper, and then you can cut it to the Upper or Tank.
It interferes immediately.
The advantage of attaching this product is that it can be adjusted without worrying about such interference.
I don't think this is a product that requires any other advantages.
Costco
Best. I bought it because it was the cheapest.
I am satisfied with the price, especially since there were no problems with the installation.
View detail
Protect Grip
Grips are consumables. They wear out unexpectedly. You can replace the grips when they wear out, but the cost of a grip heater, an OEM product of a European car, is high. Therefore, Heat Shrink Tubes are used to protect them from wear.
For fishing rods. However, I am using this product, which is a Motorcycle product, because I am concerned about the appearance of the product.
To install, simply heat it up with a commercially available heat gun. The overall length is 105mm and fits snugly without cutting.
It may depend on the Gloves, but with the Gloves I use, I don't notice any slippage.
The grips are thicker, so people with small hands may feel some discomfort.
View detail
Fits: HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY
ใส่มังกร้ของฉันแล้วมันดูดีขึ้นมากเลยทีเดียว ชอบมาก View detail
Qualtiy Clamp
Out from the box and installed it at my Honda CRF300l. Fits perfectly both sides (brake and clutch) and the plastic clamp serves its purpose not to scratch my new handlebar. Great item to enhance your bike cosmetically. View detail
Sr400 steering bearing replacement.
I had a little hard work for replacing the steering bearing sr400. This work is needed to bearing puller and small jack for lifting a bike. Also this parts is perfectly fitted to 85 sr400. Thank you for supply this parts. View detail
Purchased due to Screen interference
I put a kappaScreen on my V-Strom 650 and bought it because the Mirror barely interferes with the kappaScreen when it is fully locked.
The interference is naturally gone and I am satisfied with the expected results.
At 6 months and 5000 km, there is no Rust occurrence.
I tightened it securely and it never came loose.
No blurring occurs.
View detail
It is a reliable HURRICANEBrand with a robust construction.
This product is a trusted HURRICANEBrand and the construction is solid, and there was no sign of cracking even when tightened tightly with Bolt! View detail
Fits: YAMAHA RZ50, HONDA NSR50, YAMAHA TZR50, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, HONDA NS-1, YAMAHA XJR400, HONDA NSR250, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR
I used it to replace a rusty OEM Product!
I used this product to replace a rusty OEM Product. It comes in multiple colors, so it's great for casual custom! View detail
Fits: BMW K1600B, BMW K1600B, BMW K1600GT, BMW K1600GT, BMW K1600GTL, BMW K1600GTL, BMW K1600GT, BMW K1600GTL, BMW R1200RT, BMW R1250RT, BMW R1250RT, BMW R1250RS, BMW R1200RT LC, BMW R1200RS LC
very well & good fit
fast delivery & very fixed parts of R1250Rt. well coated surface & the other part is tightly fixed on Wunderlich adapter. View detail
Fits: HONDA NC750X, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER BOLD'OR
Used to install fog on Guard pipe
Material:It's aluminum and fairly thin-walled, so I don't think it's suitable for mounting heavy objects.
It is used to mount a Small Fog Lamp.
22.A 2mm Pipe can be diverted.
I have used the same system in my previous car to install fog lights on the Engine GuardPipe, and I have been using the same system in my new car.
It has been about 2 years in total and no Cracks have occurred.
The Pipe side edge is angled, so it is inevitable that the Pipe will be scratched during mounting and positioning.
It is best to avoid repetition of attaching and detaching, including temporary fixing, as much as possible.
View detail
Fits: HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, YAMAHA Majesty (MAJESTY), YAMAHA GRAND Axis (GRAND AXIS), YAMAHA GEAR (GEAR), YAMAHA GEAR (GEAR), YAMAHA GEAR (GEAR), YAMAHA GEAR (GEAR), YAMAHA GEAR (GEAR), YAMAHA GEAR (GEAR), YAMAHA DT50LC, YAMAHA BWS (BWS)
It's nice to be able to buy a lot at once.
Currently, there are only 4 KSR series units.
I bought 100 pieces, 23 pieces on the top and bottom, 46 pieces in total, 2 units
Once I've worked on one, if there are any abnormal vehicles among the remaining four, I think I'll have to work on it right away.
It looks so good ---------------------------------------------- ------------ It is now that the KSR series is only four.
I bought it in 100 pieces.
View detail
Fits: YAMAHA TZR50, HONDA NSR250, YAMAHA XJR400, YAMAHA RZ50, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, HONDA NSR50, HONDA CB400SF, HONDA NS-1
To One point around Handlebar
The OEM Adjuster was tasteless looking like faded Black.
It's cheap, easy to install, and it's a great accent around the handlebar.
View detail
Used to install Knuckle guard and Mirror at the same time
[How is it used?
To install the Knuckle guard and Mirror together in a rational way, we used OffsetHolder.
Was the one you received as per Image?
Aluminum Casting and appears to be Black color Painting, not Anodized.
Was the installation difficult?
Technically it's not that difficult, but how many times do you need to change the Handlebar to a Quantity:Pair (for Left and Right) The position was determined by repeatedly making fine adjustments while checking for contact with the Upper Cowl and Screen. In addition to the Offset Holder, an Opposite Thread Screw Adapter (product number:HM-10) from TANAX was used to raise the Offset Holder by 20mm to avoid contact with the Accelerator Wire. For the guard installation, the Knuckle guard bracket was installed from the underside of the OffsetHolder, taking advantage of the long screws in the Mirror Bracket.
How was your experience with it?
We were able to install multiple components together with the Refreshing without any clutter.
[Included Parts:were they on?
M10 Bolt1 pc included.
[Was there anything that disappointed you?
I think it is a little expensive. less than 1000 yen is ideal.
Other items that would be helpful
Mounting points and hang/ All ScrewBolts were coated and tightened with low-strength Screw lock fluid to prevent loosening.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA 6VCHALY 50, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA 6VCHALY 50, HONDA GORILLA, HONDA GORILLA, HONDA 6VCHALY 50, HONDA MONKEY (FI), HONDA 12VCHALY 50, HONDA 6VCHALY 70
สินค้าส่งใด้รวดเร็ว งานคุณภาพและสวยเข้ารูป ดีไซน์ เข้ากับแผงคอใด้ดี View detail
Parenthesis is good, it's been updated.
It's up-dated.
Before
The design surface looks like Rubber Print, and the rubber part deteriorates over time.
present
The design surface is made of nylon fiber. I hope the perimeter doesn't break...
Some people say it's to prevent blisters, but in my case, I just wear it because it's good for parenthesis.
It's self-satisfying, but it increases Tension.
View detail
Exactly what I was looking for
Quick shipping, and exactly what I needed. Thank you! I never ordered from this website and was worried about shipping, but I was pleasantly suprised! I will buy from them again! View detail
RAN Bretta V125's No Mirror also allows you to see the back properly.
For some reason, the screw hole for the mirror is too far inward, so I installed it on my RAN Brettta V125, which has a strange design that only shows my elbow, not to mention the OEM mirror, and even the high visibility mirror of DAYTONA.
The result is Large satisfactory. You can see the back properly.
It's also a great way to keep your style intact.
View detail
Fits: HONDA MONKEY125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA CT125
SP TAKEGAWA handle bar gurad
i bought a SP TAKEGAWA handle bar gurad I bought it to install GoPro. The installation method was so simple that it was easily installed. When the weather gets better, I am satisfied that I can install a GoPro and ride it. View detail
When I replaced the Mirror, it became difficult to see.
ZrX1200DAEG with Cross 2Mirror
I could only see my arms, so I installed them.
The angle needs to be adjusted, but it's much easier to see.
View detail
Mirror's angle can be adjusted more widely.
The OEM mirrors on my Honda, Grom, and JC92 were difficult to see (and now that it's getting colder and I'm wearing a fuzzy jacket, I'm sweating even more because my body is reflected in the mirrors), so I switched to the Takegawa mirrors. So I installed a Tanax Spacer for height adjustment and this OffsetHolder, hoping for a wider range of Mirror angle adjustment.
With the OEM mirror, my eyes would often get tired, but now that the mirror is higher and my field of vision is wider, I can see behind me better and my eyes are less tired! I'm glad I did it, and I recommend it!
View detail