Reviews
A familiar Position!
I came back to Motorcycle, which I gave up a long time ago, by chance.
Position out for starters! My old Hardy bar, still for sale!
Compared to the original effex handlebar that came with it.
The rise from the Handlebar Post is rapid.
Fist position doesn't change much.
Large hanging angle (my favorite)
Light
The Handlebar should be replaced to suit your body!
However, I am thankful that after more than 15 years, they are still selling this Handlebar!
View detail
It's high enough, but not too high.
The curved shape of the handlebar makes it taller than the riser, but it is still vertical, making it more handlebar-up type than expected when installed.
This may be good for a lower body and for raising Handlebar.
View detail
Handlebar replacement to improve position
The Intermediate is the perfect height and the Riding position is perfect. View detail
Handlebar without a doubt
Unlike the cheap Xhua products, I feel that the anodized surface is good without unevenness or distortion. Also, the feel of Brace is good. View detail
easy to ride
It is recommended for people who are quite Handlebar Up Type and have difficulty leaning forward, etc.
However, the handlebar is unexpectedly narrowed down, so there may be some differences in taste.
View detail
Mounted on D-TRACKER-X
MX Type? Low is installed on D-TRACKER-X.
We considered Zeta and Renthal, but decided on this one because of the price.
Details below, but generally satisfied. If it bends, I may Repeat it.
[How is it used?
Used for city driving + day touring after installation.
Was the one you received as per Image?
Color:I bought Titanium and it looks more Silver-like than I expected.
Was the installation difficult?
This was my first handlebar replacement, but I don't think there was any particular difficulty dependent on the handlebar. I had to put it on and off several times for positioning and drilling, so it might have been easier if it had a memory like Zeta's.
How was your experience with it?
The height of the Position is not that different from the OEM in terms of experience. The width is obviously wider. I am wondering if I should cut it because it is hard to pass through in the city.
I feel that the vibration is reduced as advertised by Manufacturer. (Is there an effect of the Grip that was replaced at the same time?)
[Included Parts:were they on?
Brace was there from the beginning, but Bolt was loose, so I tightened it.
[Was there anything that disappointed you?
There is a seal around the throttle side, and I wondered if I should use it as it is. I thought that I should use it as it is, but it was obvious that the movement of the throttle tube became smoother after removing the seal, so I thought it was the right decision to remove it.
I thought it would be better if it was easier to peel off the glue as it left a residue after peeling off.
View detail
Anodized age fading…
This Handlebar is aluminum and lightweight.
Very good salt for touring, such as height, aperture, etc.
But due to the nature of Anodized, it will fade…
Red in particular becomes White-ish and seems to deteriorate at a faster rate.
I've been using it for many years and have no complaints about the Position, but it faded
I was in a tight Koku Pit in the
This is an exchange to Middle Bar at Fana TEC.
There was almost no change in Position and no discomfort at all from Hardy (laughs).
View detail
Used in FTR223
[How is it used?
Used on FTR223.
Applications:City driving, Touring, Circuit driving
Replacement from OEMHandlebar, used for about a year.
Was the one you received as per Image?
It's just like the image, there were a few different types but the height was just right.
Was the installation difficult?
There are many parts that need to be removed, such as the handlebar body, switches, throttle, etc. It will take some time, but if you have the enthusiasm to replace the handlebar, there will be no problem.
If you want to drill a hole for the switch attachment and trim the width of the handlebar, you will need a power tool and a thread saw, which will increase the difficulty.
There is no need to extend the Clutch Cable or Throttle Wire. They can be used as is. (Shorter than the OEMHandlebar, so it can be pimped.)
How was your experience with it?
Since I did not have a dirt driving application at that time, I wanted a RoadHandlebar that was narrower and lower in height, and this product was exactly that.
The position was comfortable and I didn't get tired while touring.
The Handlebar vibration was minimal, and the stiffness of the Handlebar was moderately good.
At the time, I didn't feel any inconvenience because I didn't have a charging port or a smartphone holder attached to the Handlebar, but if I do, I think the space will be a little insufficient.
I needed a wider handlebar for the Motard race on my FTR223, so I replaced it with an Extreme bar from the same manufacturer, which is no longer available.
The wide Handlebar is much easier to use in Dirt.
For those who don't feel comfortable with the wide OEM handlebar of the FTR223, Recommendation.
[Included Parts:were they on?
Handlebar Brace
[Was there anything that disappointed you?
None in particular
Point and hang of installation
Describe the hang of the switch box attachment, not the HandlebarBody.
Positioning for the Switch box (Anti-rotation) There is a projection for
If you want to use it for secure positioning, you need to drill a hole in the HandlebarBody. If you don't drill a hole in the handlebar body, it won't physically attach.
So, if you want to install the switch box without drilling holes, you can scrape off the protrusions on the switch box.
In that case, use the Switch boxMounting Bolt (Screw) It is important to tighten the screws as tightly as possible to prevent the switch box from rotating.
I've had to scrape off the protrusions in previous Handlebar replacements, but the Switch box spins slightly and I didn't feel any problems there.
In the case of hole drilling
Electric Drill
Drill (Φ5 or Φ6)
Jig for drilling
Cle 556 (substitute for cutting oil)
It is safe to work with the
If you do not have a drilling jig, you can use the
Hammer
Punch
Make an indentation in the hole with a punch to prevent the drill from escaping.
Then I concentrated on drilling.
View detail
KSR80 Handlebar Replacement
It is a used KSR80 with 16,000Km mileage, but due to its age, there is a lot of rust on the details of the handlebar, and I decided to replace it because it is a place that is noticeable when driving. I decided to replace it.
I researched on some Reviews and selected this product which is close in dimension to OEMHandlebar.
The quality is nicely Anodized Aluminum Handlebar.
I thought it was the same size as OEM by research, but there was a slight error in aperture and height as shown in the picture. 。
When I actually installed it, I felt that the Handlebar was much lower, but since it was narrowed down, it seemed just right.
The OEM has a reinforcement bar welded together, but this product has an aluminum handlebar braze, which is very cool and I like it.
View detail
It's a little different than I expected, but I'm glad I switched.
[How is it used?
The Z900 has a wide handlebar with a small aperture, which I felt was a little too far and low for my size.
Was the one you received as per Image?
I bought the Gun meta, but the color is Blueish and doesn't look like Gun meta.
Also, when I looked at it side by side with the OEM before installation, it didn't look much different and was a little different from my expectations.
Was the installation difficult?
There is nothing particularly difficult, but it is troublesome to replace the Grip, and it is necessary to open the hole to fit the protrusion of the Switch box's stopper with the Drill, so it may be a little Large strange if you do not have an electric Drill.
The cables and hoses were fine as OEM.
How was your experience with it?
The height and distance of the Handlebar did not change as much as I expected from the NORMAL, but the width has been narrowed to the Large width from the OEM and the aperture has been added, so the Grip position is closer to the body and easier to ride. Clearance with the Tank is not a problem even if it is cut to full lock.
The aluminum bar is lighter than the steel bar. I did not feel it.
In general, I'm happy with the bike and it's more fun to ride.
[Included Parts:were they on?
Material:Aluminum Brace bar is included, but I removed it because Z900 can't be installed because Meter unit is in the way.
[Was there anything that disappointed you?
The height and closeness of the Handlebar did not change much, but if I want more change, I will have to replace the Cable and Hose.
I'm very happy with this product.
View detail
Daisan Keihin Spec.
This is the old Handlebar.
I am surprised that this product is being released in the age of harmony.
I liked the color of the Gold because it was glaringly different from the calm atmosphere of the Gold of posh.
If you install it in an air-cooled Large type four-engine, it will become the old Daisan Keihin Spec.
View detail
A little more forward
It originally came with the Motorcycle, although I don't know the OEM so I can't compare Position is not bad If I wanted to, I would have preferred it a little closer to the front Also, I think the texture is good
I'm considering replacing it because of the recent noticeable Wound and Dullness In addition, when it came to my hand, there was no anti-vibration measures such as Weight in Handlebar I suffered from numbness in my hands for a while Without
View detail
Very good
i use it on my gsx1400 and the Handlebar width makes it easy to use it on big bikes It can be handled
This is the third time I've purchased this as the pull is set up to be good
View detail
Is choosing Type a Drumstick?
The OEM's Handlebar position was high and I replaced it with Rear Sets, so I did not like the boarding position and exchanged it.
I worried about whether it is Row or Medium, but I did not know how much it would change unless you tried it, so I chose to select Row.
As a result, it became considerably lower than the OEM, the attitude also looked like a slump and it became quite easy.
I can not compare because I do not know other products, paint is also beautiful, Handlebar Brace is also attached, I think that it is worth buying.
However, although Seal? Is affixed to the bar, it is extra because it is necessary to peel off after all.
View detail
It is a good Handlebar
Exchange as OEMHandlebar was bent.
The same shape as AX-1 OEM ? Since it is Size, install it without problems.
Handlebar Guard can also be installed, good color and texture.
View detail
I do not match it.
It was too wide..
I made a little cut at the edge, but it became imaichi like balance.
It was still worse that the original width was wide.
It is my selection mistake.
The product itself is solid.
However, as the finish of the surface was shiny paint, I felt a feeling of mildness.
View detail
Used with KSR 110
I used it by exchange of Handlebar of KSR 110.
The texture is very good.
I was riding this for a while for a while but I wanted to raise Position a bit more, so I tweaked it with Bar rise kit.
After that we will verify the durability of Anodized.
View detail
It is good.
After all it is a good Handlebar. I used Red color until now, but after 21 years
Anodized Processing faded, I replaced it because it became a mottled pattern.
Next time I turned to Titanium color which seems to be fading stronger.
The nice thing about Handlebar is that Handlebar itself absorbs vibration, so your hands are not numb,
Elbow and shoulders are also easy to get tired, even if you travel long distances, you can reduce the number of breaks.
Some people think that this softness is anxious, but I want to run a long distance at a stroke
I think that I brought it to people.
It is Handlebar which can not quit once using it.
Even compared to other Handlebar's price, it is considerably cheap, so please add another color for another change, another one
You can buy it..
View detail
I am satisfied..
I think that the price that I think is lighter and shock-absorbing than OEM is cheaper compared to others and I think that it is reputation. Medium is used for DT 200 wr but it was a form which was quite similar to OEM when arranged side by side for reference. View detail
Good
Thinking that it is close in dimension to Handlebar I was looking for, purchased this time. Compared with Large hand maker property in terms of price, it is cheaper. As the withdrawal is Large, when attaching the Handlebar Guard you need to extend the mounting bracket. It is a difficult point to have few color choices, but there are circumstances of Large people there. View detail