Reviews
usually
Installed on HURRICANE's Duralumin Pipe Handlebar.
It is a very ordinary Bar end cap, but I think it is a nice slit in it.
Rubbers for inner diameters from 14mm and 18mm are included.
View detail
It was easy to install.
I didn't have a problem with it.
It would have been nice to have some sort of instruction manual.
It was so easy that I forgot to take pictures!
Prahan or Rubberhan is easier to work with.
I think it is better to wet the parts with Parts cleaner than silicon spray before insertion.
View detail
Bar End
It must be cheap, but this is how it is. View detail
Used to install external grips on af09.
[How is it used?
Used to install external grips on af09.
Was the one you received as per Image?
Yes.
Was the installation difficult?
Easy
How was your experience with it?
Made by HURRICANE for safety and security.
It looks Simple and cool.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Used to attach external grips to af09.
[How is it used?
Used to attach external grips to af09.
Was the one you received as per Image?
Yes.
Was the installation difficult?
It is easy even for beginners as all you have to do is put it in the handlebar and turn the hexagon.
How was your experience with it?
Made by HURRICANE for safety and security, Simple and cool.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Knurl process is working.
Although the difference is very slight, the Knurl finish gives the product a much more luxurious texture and feel. View detail
Mounted on the company's Swallow handle
Since the bar end was replaced with the company's Swallow handle, the bar end was also selected from the company's compatible products with SliderType and Weight.
Installation is general, and is done by attaching it to the end of the Handlebar and tightening the Bolt at the Bar End.
I drove the car after installation and felt very little hand-shaking vibration.
However, since the swallow handle itself is made of steel and is sturdy, it seems that inner weight can be added depending on the handlebar to be installed and the type of car.
As for the Slider function, I haven't tipped it over yet, so it hasn't really worked, but if it does, the Handlebar won't get stuck and around the Stem? I was hoping that it would reduce the Damage of the Stem.
View detail
Size is different
I ordered an M6 and received an M5 even though the bag said M6.
I couldn't wait to replace it, so I drilled the holes myself with a Drill and re-cut the screws with an M6Tap and installed them.
View detail
Expected
Length can be adjusted in combination with Weight. Car inspection OK. View detail
No more vibration.
Installed when changing Handlebar. It is good because the vibration is gone. View detail
Handlebar width adjustment.
Added to HURRICANE SSC Side cap.
Extension Block.
One extension is 10mm.
I am using two of them connected together, but because of their convex shape, there is no wobble once the bolt is tightened, and I am not particularly worried about it.
It may need to be retightened over time, though.
The Handlebar width, which felt tight, was widened to allow for an easier ride.
View detail
For adjusting handlebar width.
The vehicle used is a motorized Scooter.
I want to put an ACTIVEHigh throttle on this thing too!
This is where it all started.
The OEM is an old-fashioned Scooter, so the throttle body is in a HandlebarCowl, the grip is Non-Penetrating 115mm, ← so it's a Quantity.:Pair (for Left and Right) The Handlebar length is also different in
Welding extension or Cutting Handlebar is also a hassle.
Originally, there was a feeling of tightness in the width between Grips, so I took the plunge and used the Quantity:Pair (for Left and Right) Both are to be extended.
I have been looking for. I wondered if there was anything I could do ….
… about a month (laughs).
There it is. It's HURRICANE. It's a great place to get an itch.
High throttle body has 120mmGrip outside Cowl.
Extension of just over 25mm approx.
The bar end section is simple, not too conspicuous, and very stylish. It is perfect for my taste.
Fine-tuning with Extension Block and Washer, Quantity:Pair (for Left and Right) They can be aligned.
I think Large sturdy in terms of strength … maybe.
Well, we managed (laughs).
It really is easier to ride.
View detail
Was it really necessary?
Used on a Gixxer 250, hoping it would help reduce vibration at 8000 rpm and above.
Design is NORMAL style and it is hard to tell if it has been replaced at a glance. Personally, I am OK with it.
Appropriate +Driver when removing Normal bar end (No.3) You will have to prepare a Screw lick if you do not have a
In addition, a 4mm Hexagonal Wrench is required for installation since it is an M5Bolt.
It might be better to have OthersSilicon spray. (Ours got stuck in the middle and wouldn't go in without it.)
It weighed about 250g even in NORMAL, so +100g would be effective.
After the replacement, it is true that the vibration is reduced a little, but in our case, the Engine itself vibrates at 8,000 rpm, so is it just a temporary relief?
However, the weight balance seems to be closer to the edge of the handlebar than in NORMAL, which changes the bending habit a little.
It may be advisable to introduce an additional Option Weight for further vibration reduction and balance equilibrium.
We will see how it goes for now.
I don't know about the protective properties. I don't even want to try it. w
View detail
Good and reasonable price
Looks good and minimal. Nice quality also. Also good to use with other weight system combined. Maybe using this for ohter bikes too View detail
HURRICANESSCHeavy weight bar end
My previous Bar End was rusting out, so I installed this one as a trial.
The size is Exactly here for gixxers with a Handlebar inner diameter of 18mm.
At 362 g per unit, they are about twice as heavy as the Bar End we used to use, and the vibration seemed to be much less.
I quite liked the Simple look and OEM-like appearance.
It seems that the weight can be increased with additional Option Parts, so it is good to be able to change the weight to suit your preference.
View detail
Good and understated!
I chose it for its understated design. The texture is not bad, but … Hmm? If you look closely, you can see that the Bar End and the Weight are in different colors! View detail
I have been able to use it without any glitches!
[How is it used?
Bar End is required because of the hole type Grip.
Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
Easy to install.
How was your experience with it?
There are no particular problems and I am able to use it.
[Included Parts:were they on?
Quantity of Rubber and Screws:Set
[Was there anything that disappointed you?
Not particularly, but Material:It is Aluminum and is easily scratched.
View detail
Fits: KAWASAKI ZR-7/S, KAWASAKI ZRX400, KAWASAKI ZRX400II, KAWASAKI Estrella Custom, SUZUKI GSX250FX, KAWASAKI BALIUS2, KAWASAKI BALIUS, KAWASAKI ZEPHYRX, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, KAWASAKI ESTRELLARSCustom, KAWASAKI ESTRELLARS, KAWASAKI ESTRELLA
Utilized for NSR50
I used it on the Bar End of a Φ22mm Made by HURRICANEHandlebar. It is a very important part because it will be a guard in case of tipping over. It is inexpensive and easy to replace. View detail
It's a normal Bar End.
It's a normal Bar End.
It's weighted.
Of course, this does not seem to have much effect on 4-cylinder engines.
This will work for TWIN and SINGLE.
It's more functional than something that focuses on the eyes of a desga. (Weight) Emphasis.
I'm focusing on weight, so I can't help the appearance. (A little sloppy.)
This time, I installed it on the same HURRICANE Handlebar.
The others. When you tighten the bolt, there will be a gap between the grip and the bolt. If there is a gap between the two parts, you can use a plastic hammer to remove it.
Parts cleaner will vaporize eventually, so no problem. You can't do that with Raspene.
View detail
Fits: KAWASAKI ZRX400II, KAWASAKI ZRX400, KAWASAKI ZR-7/S, SUZUKI GSX1400, YAMAHA YZF-R1, HONDA PCX125, KAWASAKI Estrella Custom, HONDA CB1300 SF, HONDA CB750, HONDA PCX150, HONDA VFR400R, HONDA SILVER WING400, HONDA SILVER WING600, HONDA FAZE, HONDA FAZE Type S, HONDA FORZA Z ABS, HONDA FORZA(MF06), HONDA FORZA(MF06), HONDA FORZA(MF08), YAMAHA FZ400
Happy with the look and feel
I installed it on my Retro Motorcycle.
The texture is good and Simple.
View detail