Reviews
The size was perfect!
I used it on the Grip end side with the Grip heater on my CL500. The OEM handlebar end has female threads and can be installed perfectly with the included bolts. View detail
Slider effect is not so strong.
I think the Slider effect is not so strong, but the Designability is good.
There has been no fading in about one to two years.
View detail
The next thing you know, they're gone.
The detents are co-spinning during installation. It is tightened to some extent, but it is not removed due to vibration.
Tighten it to the same diameter as the inside diameter of the Handlebar before installation, and tap it in with a plastic hammer to make it easier to tighten.
View detail
Although it is parts of an off vehicle, it uses for SR. Although green was chosen according to the color of a car body,
Although it is parts of an off vehicle, it uses for SR.
Although green was chosen according to the color of a car body,
View detail
If you use Open Type's Hand guard, I want it.
I use an open end hand guard on my Enduro racer and I always make sure to put it on because I don't want the grips to tear when I fall over. Especially, this SwivelType is a type that only the Axel side is fixed to the Throttle tube instead of the handlebar, so it is less likely to cause trouble around the Axel when falling down during a race, and is a recommendation for racers. It also looks good with the accent. View detail
It is necessary for Mast when repairing and removing.
It is very difficult to reuse something that has been removed for Handlebar replacement, etc., if it eventually becomes unusable.
Also, if the Hex part has a governor, replace it as much as possible.
When removing the Quantity:You don't have to worry about anything if you buy from Set.
Especially before entering a race... I get unnecessarily impatient.
I'd appreciate it if you could make it a little harder to turn...
View detail
For off-road motorcycle Bar End protection
With the Closed End OffRod Grip, the Bar End portion will inevitably tear or be damaged in the event of a fall.
I installed this ZETA bar end plug because the Grip gets damaged quickly after a lot of tumbling.
Because the Throttle side was originally replaced with ZETA's Throttle tube, there was a hole from the beginning so that this Bar end plug could be attached. However, in order to fix the plug, it was necessary to fit the lock nut in the socket of 10mm and tighten it with Twrench at the back of the throttle tube. A little ingenuity is necessary.
View detail
Repair item
This is an Adapter of Hand guard which can be removed if you gap a little.
It's easy to lose, so it's nice to have it as a repair item, but it's a bit pricey….
Quantity:1 Set of 2pcs. and when you lose it, it's usually one of them, so it's safe to keep the other one in your luggage as a spare.
If the Adapter becomes rickety, it will wobble no matter how hard you tighten it, so regular replacement is also recommended.
View detail
It's expensive …
I used it on my SEA BASS DR250R
I was using ZETA's PROArmor Handguard
Changed the handlebar from a steel handle to an aluminum handlebar It is now necessary for us to
The Steel handle has a Large I.D., and the Aluminum Handlebar has an I.D The Bar End Adapter does not fit in the Bar End Adapter, so I had to change it So I had to change it because the Bar End Adapter does not fit in there
Replacement Bar End Adapter for PROArmor Handguard This is the Bar End for the Hand Guard Mount
I appreciate that you can get it in Single Item, but I think it's too expensive for you to get it in Single Item & hellip; lol
The Hand guard is a little over $10,000 and this Bar End Adapter is $2.99, I was happy if the price was a little cheaper than the Repair Parts because the price is 5000 yen
The part where the Hand guard is attached is a convex shape It is also true that there is no substitute
Single ItemUse it while appreciating that it is sold
View detail
Fits: SUZUKI GSX-R600, SUZUKI GSX-R750, SUZUKI DL1000 V-STROM650, SUZUKI GLADIUS650400, SUZUKI GSR250, SUZUKI GSR400, SUZUKI GSX-R1000, SUZUKI GSR250S, Others
OK
My hands get numb on long highway runs, so I put it on
The projection of the Handlebar's detent prevents you from attaching it to Universal can be installed properly
My hands are now less numb
View detail
It's too high
The price is too high at any rate Though it is several thousand hundreds of yen for MODEL through Next time when you buy Hand guard, it is not PROArmourGuard, but usually MODEL purchase View detail
Back from Touring..
So far I haven't had any problems with it, according to the Amazon comments section it comes off easily But it may be about using it on forest roads and off-road, but I'm not sure if it's for normal road driving It seems to be Large sturdy if it's around W
The Bar End of NORMAL is insistent in the case of CROSS CUB, can't you do something about it? I've always thought that W. This will help me with Slim
View detail
Tipping over, Bolt bent, so purchase
When falling, Hand guard Body did not have much damper,
Bolt only bent, so I bought this item.
When I bought it in second hand, because I had a hand guard, I got lost a little about how to attach it,
I was able to attach it safely. I remember that there was no Instruction Manual.
View detail
Only Bolt, I want you to join us.
Used for wr 250r. When I came back from the forest road there was no Bolt.
It is better to retighten.
I am not ordinary Bolt, so I got caught.
It was nice to purchase.
I wish I could sell bulk items.
View detail
To Accent
Instead of protecting Bar End and Grip, I bought it for Accent around Handlebar. I purchased Anodized Color, but texture was also good. Installation is particularly easy without difficulties. View detail
In for Repair
For those who fall aside with Trekking it is essential Items' ZETAHand guard.
Bolt of Bar End was shaved while using, so I exchanged it.
It is fixed in Hexagonal Wrench, but mud and earth get into this Bolt hole
There are things often.
When detaching in maintenance, it is attention that it will be easy to make a snake unless you well clean the hole.
View detail
ZETA Zeta Bar End Adapter
I have attached ZETA's Hand guard to WR 250X, but when I saw suddenly, only the end portion was gone. I do not remember dropping after wearing, so it seems I went loose and flew by vibration.
It is appreciated to be able to buy it individually, but I think that it will be a little cheaper.
Tighten regularly regularly.
View detail
About two years
I used it for Motocrosser.
Because it is a stubborn thief, it was rolling and breaking the Grip.
Well it is together now that it is together, but since we added this product, the time to exchange Grip has increased.
Just found out that the plug of Left Side is gone!
Is it due to having been riding without tightening up Screw for about two years?
I will be careful next time.
View detail
Stock required
Once you knock it down, Handlebar fixed Bolt of this part turns before Handlebar and Hand guard bend.
Bolt besides low strength, but thanks to Handlebar because there was not bending, is it a dare to drop the strength parts ??
Off owns several cars and all hand guards are attached so we have it as a spare part.
It would be nice if Bolt alone could be sold as much as possible.
View detail
To Imechen around Handlebar
Currently I remove it because it is wearing this Brand's Hand guard. Colorful hues were very useful for handling the Handlebar, especially when exchanging for RENTHAL Replica Handlebar. It has strength as it is. View detail