Reviews
Things are good.
First, the quality and texture were very good.
I was concerned because I was told it was an imported product, but there were no strange rattles or uneven coloring, and I think the surface treatment is beautiful.
but it does not go on as it is.
The first thing to do when taking it out of the box is to measure the Clamp section.
This is something I always do when I purchase external parts from Netetc. before I start the installation process.
We don't want to be in trouble in case there is a Size mistake.
In the NINJA2 Helmet 50R and 400, the OEM handlebar is placed on the top bridge, and the front fork is protruded by about 20mm.
I am sure the Owner will understand this.
In contrast, the height of the Clamp section of this product is approximately 30mm.
You get the idea.
The front fork protrudes about 20mm in OEM condition, while the Clamp portion of the product is about 30mm.
If you want to install it, you will have to increase the protrusion by 10mm.
Unless you have changed the rear suspension or lowered the ride height of the rear with Lowdown Link etc., it will have a large effect on handling if the front fork sticks out 10mm, and in some cases, it will be very dangerous if the fork sticks out too far. (I know it depends on the individual's perception.) 。
Since I have no plans to lower the ride height, I decided to ask for a return since I have not installed them, even though I took them out of the box.
View detail
![[RaceConcept]RaceConceptHandlebar Kit Up typeSIDEOffset](https://img.webike-cdn.net/catalogue/images/77031/web_Handle-Up_Type_Side_Offset023_TS.jpg)
Product with good texture
Babyface
RaceConcept. RaceConceptHandlebar Kit Up typeSIDEOffset
UP45-10
Handlebar240mm
Item Number ： R05-HS47100M
car Species:YZF-R25 (8BK)
The texture is very good and beautifully finished. Unfortunately, the brembo radipon could not be installed this time because it interferes with the Cowl.
View detail
The supplied hexagonal was licked easily and could not be used because the fixation was too loose even after tightening it.
I wanted to return the product, but the Hexagon Bolt has become so licked that I can no longer remove it.
If I purchase another Handlebar, I will discard this product. I don't need to return it.
It should be possible to fix the Handlebar part by tightening it with a hex, but the quality is so low that the Handlebar moves no matter how much it is tightened, and I will never buy this Manufacturer's again.
View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA XSR155, YAMAHA YZF-R15, YAMAHA YZF-R3, YAMAHA XSR155, YAMAHA YZF-R15
Cannot be installed on XSR155.
Cannot be installed on XSR155.
You can win products for Handlebar Bracket.
View detail
It was a terrible product...
DIY installation
I installed it with the prescribed torque, but the bolt at the part that fixes the front fork broke off I did
I contacted HURRICANE, but they said they couldn't help me I thought to myself, "That's not going to happen, HURRICANE-san
Have the bike shop install it as per the Instruction Manual I should have
It's a shame, because the Position became tremendously comfortable with the 6cm UP However, it was good that it did not reach the Large thing while running I'm scared just by imagining
View detail
Fits: HONDA VTR250, HONDA VTR-F
You had better not buy it.
I was surprised to open up! On parade of indentations, indentations on each part! Grabbed bad goods!
It might have been designed by this Manufacturer, but it was a miserable product to see how much production is overseas.
Excessive quality that can not be experienced in Japan.
With such a low quality, 24,000 yen over (Gold amount when purchased) Is too high.
Although I had you exchange it immediately, the product newly sent was slightly better than the first one. Detail Wound and Anodized flakers ... Clerk of the shop to be installed also saw the real thing and it was a donation!
The procedure of exchange is also troublesome, even if you exchange it, it is likely to repeat the same thing so I gave up. I was hoping for Manufacturer's name as WorldWalk, but I can not trust it because I am disappointed at all.
View detail
The Tap of finishing of the Anodized it is better not to open if the remains of cutting of the End mill remain dirtily although it is beautiful, or a path is also small and a processing important point hole is also mistaken by opening the hole for fix
The Tap of finishing of the Anodized it is better not to open if the remains of cutting of the End mill remain dirtily although it is beautiful, or a path is also small and a processing important point
hole is also mistaken by opening the hole for fixation reversely [ right-and-left ] was also astringent, and it was failure.
View detail