Reviews
Fits: SUZUKI ADDRESSV125S, SUZUKI ADDRESSV125S, SUZUKI ADDRESSV125LIMITED, SUZUKI ADDRESSV125G, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125LIMITED, SUZUKI ADDRESSV125LIMITED, SUZUKI ADDRESSV125G, SUZUKI ADDRESSV125G, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125G, SUZUKI ADDRESSV125G, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125
NCY V125 High Solo AXISCell start position is △.
Made in NCYHigh throttle for ADDRESS V125!
Since it is for a V125, it is in the form of an OEMAccelerator Wire Bracket, so it is inserted and fixed with a quick turn.
【attachment】 It is quite tedious. Slowly trying it over and over again.
The wire length is adjusted to the longest by adjusting the screws and positioning the High Solo Thailand Ko.
The stopper bolt can be made tautest and shortest by placing a washer in the front screw hole and letting the bolt protrude to the limit. From there, adjust the bolt again with the Adjust Screw to make the bolt taut to the extent that there is just a little bit of play in the bolt.:Set。
[The key to tautness].
Iron when it is cold when stretched to Limit (Stainless Steel) The wire becomes shorter and slightly pulled, and the Idling remains high. Therefore, the tension changes between winter and summer, and also changes while riding, so adjustments are made in anticipation of this.
[Made]
The Thailand core and Throttle cone are one piece, so you can rest assured.
The cheaper CHINA models have a screw-type joint between the thailander and the throttle cone, so it is possible that the joint may come loose.
[The only drawback].
When mounted horizontally, the Axel onStart position is quite low, so full opening requires a lot of wrist twisting down to the bottom.
*This is tilted more forward than in the photo.
It would be easier to operate if the Axel opening was a little less and it could be opened more fully, but … still, it is much higher solo than the OEM or the OEM Throttle holder type which is 30% higher solo and is very easy to control and ride, It is very easy to control and safe because it moves as you feel and is stress-free.
Axel keeps the Grip in a fixed position and there is almost no need to re-grip it!
View detail
Fits: YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X
Hazardization
Installation is easy, and the HeadCowl can be removed with a single screwdriver. The special harness is attached, so all I had to do was pull it out and replace it. View detail
Fits: YAMAHA 7PSJOG, YAMAHA JOG, YAMAHA JOG, YAMAHA APRIO, YAMAHA APRIO, YAMAHA VINO, YAMAHA VINO
Completely self-serving lol.
To be frank, I don't know who would spend such Gold on Drum brake's APRIO, but I bought it on impulse.
Texture quality is very good.
That's all there is to it.
It is not different from OEMLever in terms of weight reduction or grip feel.
However, the product box is also luxurious and self-fulfilling.
That's all there is to it.
The cospa is the worst, but the custom feeling is meh!
View detail
![KN Super Throttle Cable [L-shaped Low Height Type]](https://global.webike-cdn.net/photo/impression/48/48041d248746f07053ecdf924bec5787L.jpg)
Fits: Others Universal
EssentialItems when Big carburetor is installed on ZOOMER
When we installed the Big carburetor from Other Brand Product on our ZOOMER, we needed to replace the Throttle Wire as well. I measured the required length and found it to be close to 170 cm.
First of all, no matter how much information you have, there are many cases where you can't know about this kind of Items without checking the actual vehicle. In my case, I was not sure what to do because I had an extra Cable if I used the same arrangement as the OEM Cable. As a result, I rerouted the cable to the Right Side at the Neck of the Frame (the side in front of the Fuel Tank) and used the opposite cable routing from the OEM, and the length was about right. If the Cable is too tight, it may cause stress on the Cable and prevent it from operating smoothly, so I think it is better to have a little extra room.
View detail
Fits: SUZUKI address V125, SUZUKI address V125, SUZUKI address 125, SUZUKI address 125, SUZUKI address 125, SUZUKI address 125
V125g
I was looking for the Address 125 screen and bought it because it was cheap. It was nice to have a knuckle guard included. It's windproof, but it's the best for a dress-up. The difficulty of installation is not high, so even ordinary people can easily install it at home. It takes approximately 30 minutes. ------------------------------------------------------------ -------- I was looking for an address 125 screen and purchased because of the low price. It was also good to include the knuckle guard. The windproof is terrible, but it is the best in dress -up. The difficulty of installation is not high, so the general public can easily install it at home. It takes about 30 minutes. Powered by Google Translator View detail
Fits: YAMAHA NMAX155, YAMAHA NMAX125, YAMAHA NMAX150, YAMAHA NMAX155, YAMAHA FORCE155, YAMAHA SMAX, YAMAHA MAJESTYS, YAMAHA NMAX125, SUZUKI ADDRESSV125, SUZUKI ADDRESS V100
Better than the OEM Option
I think it's almost identical to a similar Knuckle Visor on the OEMCatalogue.
It's much cheaper than that, which is very good.
Do not tighten the Screw on the bracket and the Visor too tightly as it will cause cracks in the Visor.
You need to be careful about the amount of force you use.
View detail
Price satisfactorily satisfied
I attached it to SUPER CUB 110PRO. OEM will not get warm at all. Because the Headlight turned to an LED, because Wiring was only fine lines, I took power with Battery directly using Relay. It is not as warm as it is attached to the Large type motorcycle, but it is almost satisfied. Since the product is 115 mm, I used two Spacers and it is used, but since Blinker switch got far away, I got used to it at the beginning, which made me feel uncomfortable. Although it says that it can be adjusted with Spacer in order to attach it to automatic two wheels, it is short. View detail
![Stage 6 Brake Lever Grip [Orange]](https://img.webike-cdn.net/catalogue/14762/05312032_51a88a5d1ac0e_TS.jpg)
Once received the goods.
Once received the goods. Good quality products are very easy to install. Affordable and fast Easy to use. One color in use and very good packaging. One set of 2 pieces, both left and right, but the logo removed very easy and sticky. View detail
![Stage 6 Brake Lever Grip [Orange]](https://global.webike-cdn.net/images/reviews/119/00001005119L.jpg)
Once received the goods.
Once received the goods. Good quality products are very easy to install. Affordable and fast Easy to use. One color in use and very good packaging. One set of 2 pieces, both left and right, but the logo removed very easy and sticky. View detail
![GP Style Dual Collar Lever [SMAX / MAJESTY S / CYGNUS Type 4/R]](https://img.webike-cdn.net/catalogue/14190/11142014_5647179b3fdf9_TS.jpg)
Fits: YAMAHA BWS125 (Bewith), YAMAHA BWS125 (Bewith), YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Majesty S, YAMAHA SMAX, YAMAHA Majesty S, YAMAHA SMAX
Design, quality good! Do you have some fingers?
The shape is the same as OEM, it is not far away and it is a safe distance feeling. I think quality is good for the price. However, because the corner of Lever is standing a bit, I feel a bit of pain in my fingers when I clench it. I do not know how this will affect because it is not used at medium and long distances, but if it is a useless person such as Parking lock, Adjuster, Design thinks that it is quite good making and I think that it is a good product superior to Cost performance. I am satisfied! View detail
Fits: YAMAHA BWS125 (Bewith), YAMAHA BWS125 (Bewith), YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Majesty S, YAMAHA SMAX, YAMAHA Majesty S, YAMAHA SMAX
BW'S125(SEA6J)
I installed it on BW'S 125.
Black according to body color / I chose Blue.
I like the color well and I like it.
ADIO's Brake stopper could be used as it was.
View detail
Improves ease of braking
Simple way to make braking much more comfortable when you're not wearing gloves、 on short jaunts on my scooter around my neighborhood. View detail
The starter switch is great and solid . Best fitting in my takegawa handle bar. As long as it's from Japan . I like it so much . thank you
The starter switch is great and solid . Best fitting in my takegawa handle bar. As long as it's from Japan . I like it so much . thank you View detail
Although only the lock plate was originally required, the prices of lock plate brand-name parts were too high, and it chose the kit which is a set altogether at the almost same price.
Although only the lock plate was originally required, the prices of lock plate brand-name parts were too high, and it chose the kit which is a set altogether at the almost same price. View detail
It attached to the aprio type 2. Since it was a cable of blue, appearance also joked. Since attachment is general-purpose, processing may be necessity. it is seldom conspicuous -- since a price is not carried out so much, either, although I th
It attached to the aprio type 2.
Since it was a cable of blue, appearance also joked.
Since attachment is general-purpose, processing may be necessity.
it is seldom conspicuous -- since a price is not carried out so much, either, although I think that it comes to be alike custom, I think that it is good for repair.
View detail