Reviews
Throttle Cable tip processing was messy.
I was satisfied with the quality of the product, but the ball on the Throttle Cable attached to the Throttle was poorly machined on the Throttle mounting side, and it did not fit without modification. View detail
Fits: HONDA CB223S, HONDA CB400SS, HONDA FTR223, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, KAWASAKI 250TR, KAWASAKI W400, KAWASAKI W650, KAWASAKI ESTRELLA, SUZUKI ST250, SUZUKI ST250 E Type, SUZUKI RV200 VANVAN, SUZUKI GRASS TRACKER, SUZUKI VOLTY, SUZUKI VOLTY, YAMAHA DRAGSTAR250, YAMAHA SR400, YAMAHA SR500, HONDA REBELUp half-wheel* with AMALThrottle
Changed from a bifurcated Wire type for independent Carburetor
I bought a battered 900SS (900SL) and am Restore.
The FCR Carburetor Body is used for the carburetor, but it is not a two-cylinder one, which is often used in car-specific kits, but independent for the front and rear cylinders.
(Independent Carburetor is designated because the radical Camshaft has teamed up with)
For Independent Carburetor, generally comes with a Car Model Kit Throttle Wire branched in the middle." is commonly used.
It is normal to have two branches and four wire ends because they are used for the open and closed sides, respectively.
That's how I used to do it.
To be precise, the Reverse Side was removed because of the poor Throttle Fee Ring, and only the Open Side was used by maintaining the smoothness with frequent maintenance.
The fee ring has been improved considerably since it is only on the open side, but there is still a branch joint in the middle of the ring, and it lacks directness.
To overcome this, we prepared this Wire to pull each Carburetor to Direct.
Wire itself is quite normal, nothing special to say.
If anything, the middle Joint is Material:I'm glad it's Stainless Steel, because I don't have to worry about Rust.
However, there is a bad part, the molding shape of Thailand is a little rough...
Of course, it is not unusable, and there is nothing wrong with using it as it is, but it is not a problem to use the bean-jam-filled wafers. (Monaka) I am concerned about the raised areas of the mesh that were formed by the matching process.
Since the thailand part may rotate slightly at the beginning of opening or just before full opening, the round thailand part will improve the fee ring at the very small opening angle.
I used File to round it out before I used it.
Even if the fee rings are not affected, the thailand coils without any snagging are easier to maintain.
Also, there is no coated tube inside the Outer tube.
It is a Wire configuration with no features whatsoever, consisting of Spiral Tubes made of the old-fashioned Gold genus.
So the first lubrication is a Large thing.
Without oil, the feel will be rough, and with high viscosity oil, it will be sluggish.
On an FCR Carburetor Body with the Reverse Side removed like mine, it is fatal and life-threatening not to be able to spackle back.
This is not limited to this Wire, but try it often before lubricating with the best Oil.
View detail
very satisfied
There was a situation where the clutch cable suddenly broke, so I ordered it in a hurry, and the delivery was really fast.
The product is also very satisfactory. If you need a longer extension clutch cable by lifting the handlebars up, you can purchase it.
You will use it very satisfactorily. I am very satisfied with the speed of delivery of the product and the build quality of the product ----------------------------------- ----------------------- Suddenly, the clutch cable was cut off and I ordered it in a hurry, but the delivery is really fast. The product is also very satisfactory. If you need to buy a longer an extension clutch cable with a handlebar, you can buy it. You will use it very satisfactorily. Powered by Google Translator
View detail
Used for PositionHazard
The switch of PositionHazardRelay harnessKit was broken due to deterioration, so I replaced it with this one. 3-position switch (ON-OFF-ON) was needed, but it was a little difficult to modify due to the special wiring. It is usable for now, but I wish it had a more sophisticated design. View detail
Processed to VM38.
I bought this for a YamahaXV750E with two VM38Carburetors.
Quantity since it is a 2-stack:I bought 2pc
I once bought a 2-sided Cable for another car model, but it was not long enough and the Piece of the 2-sided part was not enough φ38Carburetor could not be opened.
The VMcarburetor is a type that directly pulls up the throttle valve, so the wire stopper is a traditional gourd shape.
There are some available, such as for SUPER CUB, but I was concerned because the lengths do not match and they seem to be very poor.
Surprisingly, I could not find one for Large size vehicles, and after much searching, I found that GOODS sells one for SR400 and purchased it.
They said it was forφ38Carburetor, but it is only for AMAL364TypeThrottle holder, so it needed Outer processing.
In my case, I have a two-stack, so Tommaselli's Quantity:2pc pull Throttle is used.
It is a pull×2Type instead of a pull/reverse, which is a bit unusual in modern times.
The Inner cable was not long enough at all, so we cut the Outer by 7cm.
The Crimp in the end section was also ported.
Thailandco used Active's products, but since Screw alone seemed to fall out, Solder was poured to fix it in place.
I was able to install it successfully, and since it can be adjusted in the middle of Cable, it can be tuned out.
View detail
Priceworthy accuracy, rare and excellent design
This is an EMGO product from Taiwan, which is famous for its Re-Product.
The M6 ShoulderBolt for lever fixation is a rare DomeHead type that understands the old car lovers.
There are two things I am not happy about.
1. The position of the fulcrum hole of the brake lever is slightly off, so it does not fit into the holder exactly when the brake is returned. (Tolerance is acceptable and there is no functional problem)
2. Cable AdjustingBolt and Holder are hard due to inaccurate screw cutting, and need to be adjusted with M8Tap and Dice. (After correction, it turns smoothly.)
Still, I am very satisfied with the overall product and would buy it again if I need it.
View detail
There are many similar products, but this one is enough!
The Harley Shovel's Blinker stopped working, and after investigating a broken ball and a faulty Relay, I thought it was a faulty Switch and purchased this product.
There were various similar products in other Brand, but I chose this one with good cosmetics.
It was easy to replace as it was almost identical to the Blinker switch that was already on it.
The new one still works well with the Switch and the Blinker lights up well after installation.
Horn is using a different switch, so I put insulated tape around the Horn wire and Tie Wrapped it to the other wires.
The texture of Plating is good, so I am satisfied.
View detail
goods Throttle Wire
I'm going to stop being a member. View detail
Fits: YAMAHA TW225E, YAMAHA TW200
The Handlebar area is Refreshing!
I was looking for a simple switch since the OEM Handlebar was too brash.
The wiring needs to be cut a little, but it is easy to install because it has a coupler.
good point
The area around the Handlebar is refreshing.
Maybe it's the Design, but it gives a Classic feel.
It's cheaper than other companies.
I can use it normally without any trouble.
A bad point
● No.
The theory behind the TRACKER Custom is to eliminate more and more parts or make the parts smaller, so these parts make sense.
I think it looks great even if you're not a TRACKER type.
View detail
Fast delivery. Good quarity. Nice chrome. It is a little bit bigger than I thought but everythings looks great. Product made in Taiwan. View detail
The product is great. Nice chrome on top with plastic on bottom. The button very good. The shipping take a little bit long, about twenty days. View detail
ของมาถึงเร็วมาก เวลาสอบเจ้าหน้าที่ให้ข้อมูลดีมาก สินค้าดูดีกว่าที่คิด จะติดตามสั่งซื้อกับทางค้านเรื่อยๆครับ ส View detail
GOOD
I used it on Honda's MAGNA50
The Brake lever and Holder on the Right Side are connected to the SPTakegawa Since I changed to Standard Type, I changed the Clutch Side as well
OldHondaStyleLever of GOODS is, as the product name suggests, an old-fashioned Honda type
It's a Standard that couldn't be better
Both the Holder and Lever were matte black
Brake lever and Holder of SPTakegawa have Luster and Black color So it's a bit of a failure lol
Well, I think it will shine if you polish it up, and that's exactly what the Brake lever has been doing from the beginning with GOODS' I should have bought an OldHondaStyleLever
The cable adjuster is probably made by Brass
I'm sure that Holder and Lever, which Mr. Minimoto sells, are also Cable The adjuster was made by Brass, so maybe, just maybe, lol
However, the mirror mount of the Minimoto's products is M8, so I don't want to do it this time We're here
The brake lever of SPTakegawa was M10, so I used this one to match it I chose
In addition, the Thai part of Cable is a Large type, so you can use it as I think MONKEYOEM's Cable, for example, is too loose
Buy a Clutch Cable for an external Lever such as SPTakegawa
Accuracy and texture are both good
I don't know how long it will last since I just put it on, but it's a rickety OEM that's been rattling around for a good 10 years It feels better than Product
View detail
What you need
A part that many people will need during each Holder replacement that the company sells
Seems like it could be sold by more manufacturers
The product itself fit into the hole with no problems
View detail
GOODS AMAL Throttle Black & Wire
A very good purchase when I wanted to clean up my handlebar. Works as a one-wire setup to my standard CV carburetor, and it works fine with just one cable. Metal throttle sleeve feels solid and a definitely upgrade from the standard plastic sleeve. Solid construction but do check what carburetor you are using as it comes with different cables depending on what you choose. View detail
To Custom around Handlebar
Inspected goods received and confused.
For mounting screws BALI many.
Especially the head of the Minus screw for ThrottleInner rattling prevention is severe, it is difficult to adjust because the tip of the slotted screwdriver does not enter.
Outer's Black Painting is very mottled and it is very suspicious whether it is really a shipping item after inspection work. (We decompose all products on our Manufacturer's website blog - Although there was content to the effect that inspecting is done)
Throttle's backlash is more than expected and unpleasant for ease of use.
I did not expect excessive expectation for Universal Product, but I do not think that it is here and it will not be very disappointing.
It is not inexpensive price range, so it is honestly useless expenses ...
If purchase directly from Manufacturer it may have been possible to consider returning, but after breaking the seal and tampering, I gave up the return.
The gap between the throttle holders after installation was also very wide, not clearly acceptable Level gap.
Based on this reason, I realized that purchasing universal type parts must be done cautiously.
☆ Evaluation is also unavoidably one because there is no 0.
We are sorry for those who like our Manufacturer products, but we will consider Holder made by other Manufacturer products.
View detail
To remove the Handlebar Switch
Buy Left Handlebar Switch for Headlight switching at removal.
I will match on my own vehicle that uses Plating parts frequently, but SwitchBody (Particularly resin portion) And Handlebar fitting parts feel very cheap making.
It is a product that can be installed without difficulty if you understand Wiring. It would be even better if you could prepare a Wiring diagram.
I fixed a commercially available Rubber sheet between Handlebar and Switch mounting parts.
Just ... It also checked the operation and there was not any problem in the operation, but again the cheapness was conspicuous, I did not like it, I was forced to restore it.
Style emphasis If Custom is refreshing around Handlebar, if such a Custom is your favorite item is not it a good product.
As above, if you can refer ...
View detail
With the renewal around Handlebar
Other companies also had similar products, but purchased this because it was cheap.
There is no manual attached to the manual so please refer to Manufacturer's website.
Do not forget to prepare the Wiring diagram of your own vehicle for installation at DIY.
The structure is simple, but making is a little cheap. I think that it is a price equivalent.
Since it is not Waterproof Specification, concern about durability. In addition, the resin part also has considerable cheapness.
Does not expect excessive, is not it good for Style-oriented Custom.
Not recommended for those who do Wiring's first work for the first time.
Us, installation. Operation verification - I did it until the trial run, but after all I did not like the cheapness and restored it ...
For your information
View detail
Push Switch does not work
Two push switches are attached, but it does not function
Even if you do not have a Wiring diagram, making it as easy as you can see inside
Since Wiring of Push Switch is Body ground, it does not turn on if it is hand painted with Black paint
I think that if you peel off the paint, I will energize, but I have not tried it
In this time I will stop using it and embed Switch in Handlebar
As it is also in Review of other people, it is very simple making
You can adjust the Length by exchanging conductors
Although it is inexpensive, it is not a thing that can be attached, so I can not recommend it to those who do Custom of electrical equipment for the first time
View detail
Minimum but easy to use. It is easy to cause poor contact with moisture.
I used it for SR.
It is more overwhelmingly easier to use than the Toggle switch etc. In Small TypeSize
Feeling that this is an easy-to-use limit.
It is durable Large unexpectedly if I thought that Material itself will deteriorate quickly as price.
One year complete Blue empty storage, but the resin part is not altered at all.
I could stain a little with Uniqlo plating of installation Band but it can not be helped.
Wiring is difficult and only Blinker and Horn can be used after all.
The lower switch is Passing or Cell (← I do not have it in SR) Only
I wonder if it can be used.
Because I felt useless, each individual CEVReplicaSwitch could be good
I feel it..
The difficulty is easy contact failure. No Guard Because it is a tactic, water accumulates
It is good to have difficulty, but the contacts are cloudy.
It is complete by packing WAKOS and AZ's Urea grease inside
solved.
Urea grease 's Waterproof nature is convenient at such times. Try it.
View detail