Reviews
I am satisfied with the look and functionality of the product.
I operate the Clutch with my index and middle fingers, but with the OEM Lever, I had to grip the Clutch enough to activate the Shifter, which was annoying, so I bought it in a hurry.
We had to wait quite a while for it to come in, but it was the right decision to install it.
I am an amateur, but I was able to replace and install it.
View detail
Easy to install, cost-effective, good-looking
This XCProtector is installed on a CRF150L with ZETAArmor HandguardBent.
The time required is about 2 to 3 minutes since it only stops two Screws on each One Side.
It looks LARGE and better as shown in the photo.
Cost-effective and great.
View detail
Cool with increased protection
ZETAArmor HandguardBent on CRF150L.
The instruction manual is also very helpful and reliable. Basic installation is also easy.
If there was a hole on the SIDE of the handlebar rubber, we would have installed it as is, but since our car was blocked by the rubber, we drilled a hole with a cutter (the Instruction Manual also says to replace the grips).
The Left Side was easily installed, but on the Right SideThrottle side, the bottom of the Rubber was blocked by Plastic.
Carefully crush this with a Hammer, etc. and install. CRF150L users, please be careful.
Once the hole is made, installation is easy and from there it takes about 10 minutes, as shown in the photo.
It looks good and has a large increase in protection.
It is good enough as it is, but we will also add XCProtector after this.
View detail
Weight reduction around handlebar
I have always enjoyed forest road touring with gasgas EC250 as a hobby.
It is an application that sometimes runs a little HARD.
Until now, I have been using ZETA's Guard with Aluminum in it,
The Handlebar end of the Motorcycle, the furthest end of the Motorcycle, is extremely heavy, and with the worsening of the Handleling,
I was struggling with the weight of the Motorcycle when I knocked it down.
Also, the fat bar's bend also became a snap, and for a long time we were troubled with the selection of a hand guard.
To be honest, this hand guard works. However, it can be easily fixed by hand, so I am not particularly dissatisfied with it.
Since it is not made of aluminum, it is very lightweight. The lever protection is also very good, and so far it has protected me well.
Total performance is very good. It seems to be my ideal Hand guard.
I would like to test how far it will endure while actually using it, since it is plastic in nature.
By the way, although it is Plastic, it is surprisingly sturdy.
View detail
Fits: SUZUKI GSX750S, SUZUKI GSX750SS, SUZUKI GS1000
Does not take into account the intent of Low Friction
Before use, the Advantage arrived in a bag with about 3 layers tied around it and very tight curvature.
It is partly bent and habitual, and although the product claims to be Super low friction, it is ruined by Advantage's packaging.
It does not seem to fully reflect the intent of the producer.
I would like to see Advantage improve the shipping conditions with a more gradual curvature.
WeBig is in the process of requesting a replacement.
View detail
Fits: SUZUKI Gixxer 150., SUZUKI Gixxer SF250, SUZUKI Gixxer 250
I'm very happy with it
It is lightweight and I am satisfied with the color.
I can only tell the difference in feel from the OEM, but the smaller grip makes it easier to use.
On the other hand, I feel that it took a little time to get used to the Tight feel of the operation.
View detail
It is a good product
I installed it on my SR400. It is a good product, and the fact that it is Japanese Vehicle Inspection Correspondence is a high point. View detail
Bar end mirror for option719
The handlebar width is very narrow and the position is very comfortable. If you are used to NORMAL, it will take some time to get used to the low speed operation. But it is easy because it is made of aluminum.
The brake hose interferes with the meter, so the mounting position is usually fixed, but it is a good product.
View detail
A bit pricey.
With bar ends made entirely of gold, the basic rule is to replace the bar end when it falls over, but in this case, only the resin part can be replaced, so there is no need to buy a new one if it is just a standing bump.
However, the replacement of the resin part is a bit Large strange.
View detail
Fits: HONDA CBX125F, HONDA NSR250R, HONDA CBR250R, HONDA VFR400R, HONDA Integra, HONDA CBR400R, HONDA SUPER BOLDOR, HONDA CBR300R, HONDA RVF400, HONDA CB400SB, YAMAHA TZM50R, YAMAHA YZF-R125, YAMAHA TZR250, YAMAHA YZF-R15, YAMAHA YZF-R25, YAMAHA FAZER, YAMAHA FZR400RR, YAMAHA YZF-R3, YAMAHA YZF-R6, YAMAHA XJ6
First MirrorBlinker installation
I put it on a yzf-25r early model.
Screw holes don't meet at all, so I have to rebuild them.
It must not be done. It is absolutely impossible for an amateur.
View detail
Fits: HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB1300 SUPER BOL D'OR, HONDA CB1300 SUPER BOL D'OR, HONDA CB1300 SUPER BOL D'OR, HONDA CB1300 SUPER BOL D'OR
Easy to use
I think this product is easy to use. The price seems a bit high. View detail
The texture and feel are both good.
[How is it used?
Because the OEMLever of the GSX-S 125 is not adjustable, and also to Upgrade its appearance.
We compared it to Endurance's Lever, but this one seemed to be more to our liking in terms of lever shape, length, etc., so we went with this one.
Was the one you received as per Image?
The texture is as good as the picture shown.
Was the installation difficult?
No problem.
How was your experience with it?
The adjustable type is easier to adjust to the position of your choice, and it also feels better when you run.
[Included Parts:were they on?
I think it came with a ManufacturerLogo sticker.
[Was there anything that disappointed you?
Nothing in particular. I dare say that the Retractable Lever was so loose that it moved immediately after arrival that I had to retighten the nut to prevent it from moving.
Blue Anodized is a little lighter than U-KANAYA's Blue, etc. I think it fits GSX-S125's Birdton Blue. (The Normal Holder has a large amount of play, so it may rattle a little, but I think that can't be helped. If you are worried about the rattling, it would be better to replace the MASTERBODY with Landor or brembo.
View detail
Lightweight bar ends from KIJIMA
Lightweight bar ends from KIJIMA, ideal to save some weight while still maintaining some vibration damping efects. Can be use on both the stock steel handlebars or aftermarket aluminium ones, as it cames with both adapters type and the Allen tool also. Overall a good quality/price product. View detail
Fits: HONDA CB1300SF, HONDA CB1300SB, HONDA CB1100, HONDA CBR1000RR, HONDA VTR1000SP-1, HONDA VTR1000SP-2
Easy to use
I think this product is easy to use. The price seems a bit high. View detail
Fits: KAWASAKI D-TRACKER, KAWASAKI KLX250, Others , YAMAHA WR250R, YAMAHA WR250X
There are some good things that only a comp bar can do.
I put a MOTARDMedium comp bar on my CRF250RLY50.
I had worn cx bar mx-123Blue before, but I thought it would be more comfortable with a little more aperture in terms of position. I decided that the comp bar would fit CRF250RLY50, which is not so strong and rigid, and bought it.
As a result Large was the right answer
The position, moderate rigidity of the handlebar, and coloring are perfect.
View detail
Stability only possible with Fat bar
This is a Review at least 6 months after purchase.
Quantity:Pair (for Left and Right) Fell multiple times on Tarmac in (SlipDown type) were, but there are no visible signs of breakage or bending, and the feel of the product remains the same.
The length of the bar is 800mm, which may be a little too large for some Japanese, perhaps due in part to the length adapted to the physique of Westerners. I use it with the bar packed.
Motocross athletes often use them without filling them these days, so if you take that into account, you can use them without any particular concerns.
View detail
Fits: KAWASAKI Z900RS cafe, KAWASAKI Z900RS, KAWASAKI Ninja ZX-4R, KAWASAKI Ninja ZX-4RR KRT EDITION
Vibration? It might be better.
[How is it used?
Touring use from mountain to city driving
Was the one you received as per Image?
Street Image
Was the installation difficult?
The work is easy. But I don't know which way to put the groove on the outside or which way to put it in!
How was your experience with it?
I feel fine vibration....like Large vibration to Small vibration?
[Included Parts:were they on?
None
[Was there anything that disappointed you?
The OEM Screw is Black, and this Screw is Silver color, which is a bit cheap w
It's cheap, that's what it is.
View detail
Fits: SUZUKI GSX-R1000, SUZUKI GSX-R1000R, SUZUKI GSX1300R
I'm glad I went with Gold.
I used to use middle weight, but the numbness in my hands did not decrease so much, so I decided to use heavy weight this time. I hope you will experience some vibration this time! View detail
Fits: Others
I bought this as a supplement.
I bought it the summer before last and have had quite a few falls.
Finally, the original round shape was gone, and I decided to buy it again in a Potato-like shape.
As far as I can remember, I fell 7 times on Right and 9 times on Left with SlipDown system, but the Screw hole did not collapse and the vehicle body slid and missed Damage.
I think Slider does a good job including Material.
View detail
Good to have a variety of colors to choose from.
This one is good because it offers a variety of Coloring choices.
Both Cx and sx bars come with Pad as standard, but the Black is Quantity related to the color of the bar.:Set
Inevitably, every time you buy a bar, Black's Bar pad will accumulate in droves! 。
There is almost no profit to be made selling them on Mercari or Yahoo!
I would like to be able to choose the color of the Pad anyway, but I think it would be better if the Pad is treated as an Option like the comp bar and the unit cost of the Handlebar is lowered.
View detail