Reviews
Made by TYGON, after all!
TYGON Tube is used in the medical field and is known for its resistance to chemicals and impurities that do not dissolve into the bloodstream, as well as for its ability to generate altered gases in the flowing fluid that do not dissolve. and not dissolve into the flowing fluid.
The TYGON is a reliable product, and it's great that it's not affected by brake fluid glycols. The transparent design makes it easy to see when the air bites, and allows you to visually check the air removal process.
View detail
Emphasis on appearance.
As mentioned in other reviews, if you insert a thin hose and dip it in hot water, it will turn a little better. View detail
Qu Rear hose
I just installed it, so I can't say anything about it yet.
Fluid, dirt seems to be confirmed.
This time, bremboBrake fluid was added.
The color is transparent.
If you add Active, RedBlueGreen, Fluid...
I think the QuRear hose is beautiful.
View detail
Precious. Purchased for Restore
I am very happy with my purchase, it is a OEM Product and I am very satisfied with the Large change, it comes with Elastic band and HoseGuard for the engine contact points. View detail
Used as an alternative to the Non-master cup kit
I used to use KITACO's Non-master cup kit, but the surface became slippery with perspiration and I physiologically disliked it, so I diverted this one, which does not sweat as much. (The cap is reused from KITACO.) So far, I don't sweat at all. So far I have not sweated. However, the price is a little bit expensive for 30cm/3000yen. View detail
Fits: Others RCSMaster Cylinder(Brake/Clutch), Others Radial master cylinder(Brake/Clutch)
Fluid Sweat
After six months, Fluid sweats and ruins it.
Quantity:I bought 2pc and both of them are ….
View detail
Fits: Others RCSMaster Cylinder(Brake/Clutch), Others Radial master cylinder(Brake/Clutch)
Good Quality & Packaging
The quality of the item is good. The hose is very durable and the clamp is fit to the hose. The item was apcked nicely without any dent. View detail
the most unlikely
Just a transparent Hose.
It's totally just for looks lol.
When dipped in hot water, it bends straightforwardly and retains its shape memory.
Ka Eraserd and is Outclassing!
View detail
It takes some ingenuity to bend it.
I bought 30cm and used it for H2SX's FBrake and Clutch, GSX-R1000 K7's FBrake, but there is a little too much.
If you put it in hot water around 60 degrees and bend it, it will memorize the shape when it cools down, but if you do it normally, the hose will be crushed.
I'm worried about durability, how many years it will last.
http://onaka-ippai.cocolog-nifty.com/blog/2021/11/post-efd372.html#more
View detail
I think I could have used a regular BlackHose…
I bought this product to try it out to see if it was available.
I think it looks better with Active's with Color and Fluid (I use Yamaha OEM).
There is a description in the instruction manual that it is possible to use it without changing that much with normal Hose, and conversely, there is thickness and hardness as much as normal BlackHose, but it is possible to bend it while heating it with hot water of 60°C.
However, I thought that BlackHose would be safe when I thought about whether it would come with YellowHose.
I'll continue to look at it and add to it if I hear anything.
View detail
brembo
With the brembo brake and tank installed, we installed this one that corresponds to the diameter.
The price is not that much, so I bought 1pc. more for Spare, Stock.
View detail
brembo
Because the size inner diameter seems to be slightly different according to the brake lever of brembo and Tank installation, it is this purchase of exclusive use.
It is good because the price is not high, but Package is not good. Although it doesn't influence the function.
View detail
Fits: Others RCSMaster Cylinder(Brake/Clutch), Others Radial master cylinder(Brake/Clutch)
Changed to brembo
I tried to connect this Hose along with bremboBrake and Tank replacement, but it seems a little stiff. It seems to be a little hard, and the tightening seems to be weak even with the attached Band.
It seems to come loose under load.
In the end, it is exchanged to a normal Hose.
It looks good, but if you take it on and off a few times, the mesh on the surface will start to peel off. It will be like
View detail
Fits: Others RCSMaster Cylinder(Brake/Clutch), Others Radial master cylinder(Brake/Clutch)
Handle with care.
This Hose is covered with Mesh and I like its high quality appearance, and I always use it when I install Master Cylinder of Tank Separated Type.
When I installed it this time, the Hose insert was too tight and the Mesh covering was spread out, causing it to come off and become tattered.
You should not work on it by force because it is only covered with Rubber hose.
View detail
Fits: Others RCSMaster Cylinder(Brake/Clutch), Others Radial master cylinder(Brake/Clutch)
It looks good.
Depending on the position of the Tank, I think you can use both two (Brake and Clutch) in 10 cm.
It is not recommended for those who are in a position where the bend of the hose is too tight.
I have a brembo RCS, H2 mouth cut tank and POSH brackets and it feels pretty tight.
If you want to install the tank horizontally and neatly, the normal Hose will be more ideal for you.
View detail
Fits: Others RCSMaster Cylinder(Brake/Clutch), Others Radial master cylinder(Brake/Clutch)
Mesh hose of Koken Original
This one looks better and seems to be more durable than the brembo OEM Hose. View detail
Fits: Others RCSMaster Cylinder(Brake/Clutch), Others Radial master cylinder(Brake/Clutch)
Koken OriginalOil Tank Hose
It has a higher quality feel than the brembo OEM Hose. It also seems to be more durable. View detail
Fits: Others RCSMaster Cylinder(Brake/Clutch), Others Radial master cylinder(Brake/Clutch)
Custom parts are all about looks!
A slightly sturdy, mesh-embedded hose
As others have written, the Hose is thicker and takes a little more care when bending it.
But since appearance is everything, I think this thickness is a large thing.
I'm sure it's thin and Mesh is possible, but that thickness seems to give it an Other Brand Product feel
Anyway, the Cool is more transparent than the regular Hose, and the Hose is more attractive than the regular Hose.
View detail
Fits: Others RCSMaster Cylinder(Brake/Clutch), Others Radial master cylinder(Brake/Clutch)
Mesh is good.
The normal rubber hose will cause water droplets to come out around the hose.
With Mesh hose, you don't have to worry about that.
I also always use mesh hose because it is safe from external shocks.
The length is 10 cm, so if you want to use it longer than that, you can't use it.
View detail
Fits: Others RCSMaster Cylinder(Brake/Clutch), Others Radial master cylinder(Brake/Clutch)
It looks good
Used for GALE SPEED's Tank and Radial master
It wasn't too hard or too soft, just right.
Mesh hose looks great.
View detail