Reviews
It can be used for any type of car.
Copper Washer or Aluminum Washer? I am torn between Copper Washer and Aluminum Washer, but if Banjo is Aluminum, then Aluminum it is.
If the banjo is steel like the OEM, it will be copper.
* Image from FZr MEETING
View detail
SWAGE-LINE:Swage lineCopper Washer #3 installation
[How is it used?
SEA BASSOEM Parts Brake Caliper Assembly brembo STYLEMA [Stillma] For 108mm mounting
[Points to note]
Be careful when installing as it applies Torque.
View detail
JA55 Left hand Brake for mounting
It was used without any leaks.
The price is for 10 sheets, so you don't have to worry about failure.
View detail
Brake CaliperCustom accompaniment
Purchased in conjunction with Caliper replacement.
We are also considering MASTEROverhaul at a later date, so the Quantity:I think 1 pc. spare in 1 Set of 3pcs.
The inside diameter is a little loose, so there is no feeling of being snugly fitted, and you can also feel the responsiveness of the crush feeling when Torque is applied.
The thin cheap ones don't feel crushed when Torque is applied, so I'm worried about using the Torque wrench, but these are thick-walled and fine.
View detail
Washer I use all the time.
It is used for GSX-R1100.
Often used for maintenance of Front brake, Clutch and Rear brake.
The relatively low cost and the choice of the number of sheets to purchase ensures that there is no waste.
I have used it many times now and have never had a problem.
View detail
Replaced with Clutch mesh hose
Used when replacing clutch mesh hose View detail
Performance and price are sufficient for your needs.
[How is it used?
Used to disassemble and clean the rear master cylinder of a YAMAHA XJR400R.
How was your experience with it?
Nothing is impossible.
I believe that the basic performance of these products will remain the same.
How did it compare to other products?
This item is 1 bagQuantity:1 Set of 2pcs. but other products are available in Large quantity and cheaper.
However, DailyMechanic like me only uses it occasionally, so I think this one is sufficient.
[Points to note]
If Torque management is not done properly, Brake fluid will leak and ooze, so be sure to do it properly.
View detail
When replacing the banjo bolt!
I bought this when replacing my Banjo bolt. As a spare! It gives me peace of mind in case of failure. The price was good and reasonable. View detail
Thick Washer
The combination of apRACINGCP2696 and High spec lineBrake hose caused the banjo bolt to bottom out, so this thicker product was used to successfully avoid bottoming out.
It is expensive, perhaps because of its thickness.
View detail
Crash washer
I used it to replace the rear brake line. It is ordinary, but it is BALIBALI for peace of mind. I use a solid product because it is a life-threatening part. View detail
Crash washer
I also purchased this product to replace the hose. It is a little cheaper than other products, so it is very helpful. View detail
For adjusting the handling of the hose.
It is the same Manufacturer's product, so there are no problems. View detail
Thank you for the fast delivery of the high quality product
I bought a washer from Webike, which I trust and buy, thank you for the fast delivery and please do not contact other people that they couldn't find the washer in the box like me. I found it. Anyway, I will write it well. Thank you. ------------------------------------------------------------ -------- I bought Dongwasha at the Webike I believed and bought it, thank you for the fast delivery, and I don't want to contact others that I haven't found it in the box like me. I found it. Thank you for using it anyway. Powered by Google Translator View detail
Convenient
Used for maintenance. When disassembling, it is essential to replace these parts, so you don't have to worry about stocking a lot of them.
It is a reliable Brand, so you can rest assured.
View detail
1pc. extra
I have 1pc. left over and will use it as a spare, but then I am 1pc. short. View detail
spare
I bought a 10-pack with a large number of sheets because I use a choice of spares and processing accuracy.
I will Repeat again.
View detail
OEM, copper, best cosmetic
It's brembo OEM, made of copper, and inexpensive.
Cost performance is great, no complaints!
View detail
Aluminum parts are made of aluminum.
The oil drain bolt is iron, and the washer used to be copper, but now it is aluminum. The oil drain bolt is iron, and the washer was copper, but I decided to use aluminum. It is softer than copper, so the crush is better, and it seems to seal better. View detail
It can be used normally
When replacing the normal hose with the mesh hose, this is the part that should be replaced because it is subject to hydraulic pressure, so if you have this amount, you can work with enough time.
I replaced it and it's working without any leaks.
View detail
Large doubles as Small
Because the number of pieces is unexpectedly necessary when the hoes such as Front and Rear are replaced, even 20 pieces are not a lot. It is not a part to be exchanged too often, but since Large also serves as Small, let's buy in bulk with room to spare. View detail