Reviews
It is a modest Parts.
I'm on a Sidecar made in Russia, Ural GEARUp 2015 MODEL.
One day, I noticed that the stop-lamp did not turn on when I stepped on the rear brake.
The Spring that was supposed to be attached to Brake's Switch has gone missing.
When I contacted the authorized dealer where I purchased it, they said that SpringSingle Body does not provide parts.
That's why I bought this one. I really only need 1 pc.
View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR)
OEM same etc.
It was used for Rear brakeMaintenance.
You can still get OEM parts. You can buy OEM Parts from Webig, but
OEM Parts does not come with a Point. So I bought this one.
OEM Parts are sold separately, but this is a Quantity:It is a Set.
If you don't care about full Original to Screw one, you can buy it.
View detail
Fits: KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4)
OEM same etc.
The OEM Indicator was full of rust, so I replaced it.
It goes into Brake CamshaftShaft without a problem.
It's great to have such small parts.
View detail
I used it on my yzf-r1 MASTERRepair
I bought a used Master Cylinder Nipple that was broken and used it in Repair. I am able to use it without a problem. View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR)
Ripro's Material:Typical of Rubber products
After about a year, the Rubber ripped open and it looked like a flower had opened.
PMC Material:This product is a typical Rubber product.
View detail
Fits: KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4)
Expect durability
OEM Parts was purchased due to discontinuation.
I previously purchased a product from another RiproManufacturer, but the Rubber cracked open like a Tulip after less than a year.
RiproManufacturer's Material:Many Rubber products are disappointing, but how long will this one last?
View detail
Fits: Others brembo Groove, Others brembo SUPER SPORTS750
To semiFloating of bremboSUPER SPORTS750disc
If there is no distortion in the Outer Rotor of the brembodisc used
By using Plusμ s semifloater with Wave washer
Since the lateral shake of Outer Rotor is almost eliminated and KnockBack is reduced, Lever touch is also improved.
The brake rotor does not rattle when riding on the street, so it is easier mentally.
View detail
Fits: HONDA CRF250X, HONDA CRM250AR, HONDA XR250, HONDA XR400 Motard, HONDA CRM250R, HONDA CRF450R, HONDA CRF150R, HONDA CR250, HONDA CR125, HONDA XR250MOTARD, HONDA XR250 BAJA, HONDA CR80R, HONDA CR85R 96-07
The difference in texture from NORMAL is obvious!
The Anodized was beautiful and I bought it with the intention of changing up the look.
but not only was the difference in texture from NORMAL obvious, but it also helps prevent injury while working.
NORMAL to protect the brake hose. (I think that) The Edge of the pressed Gold was facing away from me, and I scraped my finger on the Edge without knowing it while I was messing with the fixed Bolt.
This product has corners that are properly rounded off, so I didn't get hurt even if I touched it.
(Maybe I'm just clumsy, but...)
View detail
I installed it without bending the ROD to adjust it!
I am Tanaka Shokai (TANAKA) I installed Tanaka Showkai Rear Sets Kit B. In that case, RearBrake Rod needs to be bent and processed, but this Brake Rod was able to be installed without processing.
If you have the same spec. as me, why don't you use this ROD as a reference image and choose a ROD that you can attach without any processing?
I can't be responsible for that, but…
View detail
If you're suspicious, effect.
It may be causing you to chew air.
If you think it is suspicious, please effect it.
View detail
the expendables
Replace regularly to maintain performance.
Periodic replacement is recommended.
View detail
For Repair.
I bought this for Repair because my Breeder was getting licked during air bleeding. I pulled out all the fluid and did the replacement work just for this, but I feel it's a waste of time, so I recommend doing the work in conjunction with replacing other braking systems such as MASTER or Hose.
Also, if you have a chance, you can wrap Seal tape around the Breeder to prevent fluid leaks from the root when you bleed the air.
View detail
GCraftBrake Rod
I purchased this product due to changes in Long Swing Arm.
Compared to OEM Product, it's just a stick to fix.
It would be helpful if you could do one more thing.
View detail
I replaced the Brake Rod of DAX.
When I bought a used GCraft Swing Arm for my DAX.
It seems that the Brake Rod that came with it was the length of the Rear SetsSpec.
If you don't adjust the angle on the Brake lever side, the ROD will not be long enough.
I had it for about 2 years and now I bought a regular length ROD and replaced it.
Because it is a regular length, the width of the adjustment of the treadmill, etc. has become large, but
When you remove the rear tire and put it back together, it is difficult to put together the connection parts between ROD and Arm.
It became much more difficult.
If you make it right around the middle of the length before replacement and this time, it will be just right.
It is not so expensive Parts and I would like to replace it again if I have a chance.
View detail
For those of you who run Circuit, it's a back-up.
[How is it used?
I installed these on my Aprilia RSV4.
I was looking for something to do, but in the end I decided to go with a physical solution. But in the end, I came up with a physical solution.
Was the one you received as per Image?
It is just like the Image. The texture of the actual product felt better.
Was the installation difficult?
Lever was replaced along with it. The thing is
https://www.webike.net/sd/24108783/
Here it is, it comes with the RSV4 MASTER. Mine is a 13 year old Factory APRC.
The RSV4R has not been confirmed, so please do not be surprised.
The OEM lever is not appropriate because the Click is facing the front, so I replaced the lever.
How was your experience with it?
It is necessary to look at the situation and turn while actually running to see how much it changes when how much it clicks.
It's because the amount of Lever that goes in when there is no heat and when there is heat is different.
However, it is enough to click several times. In some cases, even one click is effective.
It is important to note that a cut is required, but I use the shortest length possible to avoid loss.
Because there is a section that does not tighten at all when the Wire is installed and it begins to turn, I felt that it was necessary to avoid it there. But if you turn it suddenly in a loose state, you will feel like it is not working, and as a result of turning it a lot, it will become quite far and you will not be able to do the brake you are thinking of, and you will fall. It is often heard.
[Included Parts:were they on?
It comes with an Instruction Manual, so I think the installation will be large and sturdy if you read it.
[Was there anything that disappointed you?
I feel it would be nice to have more color choices.
View detail
Fits: YAMAHA YZF-R1, DUCATI MONSTER 821, DUCATI STREETFIGHTER, DUCATI Multistrada 950, DUCATI Multistrada 1200S Touring, DUCATI Multistrada 1200S Pikes Peak, DUCATI Multistrada 1200S Granturismo, DUCATI MONSTER1100EVO, DUCATI MONSTER 797, DUCATI MONSTER 1200S, DUCATI MONSTER 1200R, DUCATI MONSTER 1200, DUCATI HYPERMOTARD796, DUCATI 959Panigale, DUCATI HYPERMOTARD1100EVO SP, DUCATI 848EVO, DUCATI 848, DUCATI 1299Panigale, DUCATI 1299 Panigale S, DUCATI 1199Panigale S/Tricolore
CNC Racing GP DuctFront brakeCooling system
Installation will be compulsory in the WSB World SUPER BIKE Championship from 2022.
CarbonBrakeDuct was the best.
Even with a Harley for Touring, I just put it on the Rear.
They say the difference in temperature is more than 10 degrees Celsius.
When this is at Racing level, it has a very large effect.
https://ameblo.jp/keikocookingchicken/entry-12678352556.html
View detail
Fits: YAMAHA SR400, YAMAHA SR500, YAMAHA SR400, YAMAHA SR400
A product of the street.
It is Rear hubDust cover of GermanyKEDO that comes out from DAYTONA.
The SR has a bare rear hub, so dust and garbage can easily accumulate inside the hub.
It is a product that prevents dust and garbage from entering by putting a lid on it.
good point
It is suitable for all models except casting wheel.
By the way, I have a '92 Drum, Spoke.
Before, there was a strange sound coming from the rear hub due to Garbage invasion, but it disappeared after the Cover was installed.
The precision of the parts is also high. So installation is easy.
A bad point
● No.
It's not that Garbage will break even if it gets in a little bit, but if you've been using it for a long time, there's a worry that Garbage will misbehave and damage Brake Shoe and Bearing, so you want to prevent it as much as possible.
It would be a huge expense to replace everything later.
View detail
Replace with Plain transparent Hose
In order to replace the brake fluid, I had a quantity of air bleeder in my possession.:Because the Hose of the Set was the transparent Hose of yellow color, I decided to exchange it for the transparent Hose of Plain. In the meantime, I'm going to buy this product which has a name that seems to be resistant to Brake fluid.
By making the Hose a Plain Transparent Hose, it is easier to see the switch between the old Fluid and the new Fluid, and thanks to that, I no longer consume Waste Fluid. However, it is difficult to tell the difference in the Fluid that has not deteriorated, no matter how much Plain transparent Hose is used. I could see the air the same way.
Texture is airlessQuantity:Compared with the Hose that came with the Set, it is almost the same, and the difference is that the outer diameter is about 1mm thin, so if you want to put the Hose Band between the Air breeder, you need to change the Size. After use, I wash it with water and keep it, but there is no deterioration and discoloration. However, when I become calm, 275 yen seems to have been high for the Hose of 50cm…
View detail
Used for assembly from Frame
I thought it was OEM same etc. workmanship! View detail
Fits: HONDA Shirley 70, HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA dachshund, HONDA Shirley 50., HONDA Dax 70, HONDA Mighty Ducks (ST90)
Used to make from Frame
I'm satisfied with it because I can install it as well as OEM and it's cost effective. View detail