Reviews
V-max 1200 Rear Brembo caliper support
V-max 1200 Rear Brembo caliper support. Perfectly compatible with Brembo 2p calipers. It is also an overlacing product. View detail
Fits: HONDA GROM, HONDA Monkey125, HONDA DAX125
It's a small thing.
I need it to change Caliper.
It's not very obvious, but I'm not sure if the Over text is a good idea.
Rear also wanted to Over.
View detail
About Pad Overhang
I was casually looking at the new product introduction from WEBIKE, and I saw that the UP Type of Rear caliper support for the new Crab is now on sale from OVER, so I bought it.
I knew that there were some manufacturers that sold a rear caliper support for Crab, but all of them were of the type that was installed on the underside.
As for the installation, we would like to describe our concerns about the Pad, as we have received information from others about the Pad sticking out in their impressions.
First, I installed the Support+NewCrab on the OEMdisc and looked at the contact surface of the Pad and felt about 1mm of contact on the outside.
Next, we removed only the Pad of the new Crab and placed it on the OEMdisc with the OEMPad perpendicular to the OEMdisc. The height of both the Pad of the new Crab and the OEMPad were the same.
As a result, the Pad protrudes 1mm from the periphery of the OVER-made Support, so it is necessary to shave this off.
When shaving the new CrabPad, it would be helpful to trace the outer circumference with Magic or similar to give a guide when shaving.
In our case, we attached a carbide rotary bar to a cheap wired electric drill from Home center and scraped it off, but a File or similar may also be used for a diagonal drop.
If you continue to use an OEM disc with only Caliper+Support replacement, it may be safer to drop a little more than 2mm, since the chamfer of the OEM disc is larger than that of the MADE IN SUNSTAR disc. Therefore, it may be safer to drop a little more than 2mm.
*There may be some errors due to individual differences, so matching the actual product is the best way to be sure.
As for the weight, OEMSupport weighs 391g including the bolt and OVER Support weighs 299g including the bolt, which is about 92g lighter than OEMSupport.
Both of the mounting Bolts are replaced with Titaniumium Bolt.
The total of Caliper support + new Crab + MADE IN SUNSTARRear Disc this time made it possible to reduce the weight by about 400g, but the cost was also quite high, so I thought it was not worth the effort to change.
However, the BlackCaliper felt cheap with SP's Swing Arm, so it is now cooler.
The lightweight under Spring is … I haven't been able to run it that much yet, but it's likely that I don't know much about it.
View detail
Fits: YAMAHA MT-09
Pad protrudes from disc.
As you can see from the Up photos, the accuracy is very low. The disc is OEM, Caliper is when using brembo's new Crab. MT-09SP (2022). View detail
Fits: HONDA Rebel250 S Edition, HONDA Rebel250 S Edition, HONDA Rebel250, HONDA Rebel500, HONDA Rebel250
For REBEL.
WR3 is cheaper, but after reading the impressions, I decided to go with WR3.
I can use it without problems
View detail
Fits: HONDA CBR250RR, HONDA CBR250RR
Downward is Recommendation!
It is a definite product. Accuracy and workmanship are unquestionable.
The caliper can be installed either up or down, and if it is up, the hose can be used as OEM, so it is not so difficult to install. However, if you are going to install Brembo caliper, it is recommended to install the caliper facing downwards, because it gives a race ish atmosphere and it does not cover the exhaust system, so it has a great stress-up effect. However, the hose needs to be extended with other brand products.
Since we are here, I would like to introduce the Caliper that was installed. Crab caliper 84mm. Mounting Pitch 84mm. The mounting pitch is 84mm. Also, a banjo bolt for Brembo 1mm pitch is required.
Parts required for downward mounting are 800mm hose (Swage line for me), SIDEBend 20 degree Banjo adapter, and Flare nut adapter (convex). And of course DOT4Brake fluid. There is a hang for air venting, and the Caliper must be removed from the Bracket and turned upward to vent the air.
View detail
Fits: HONDA CBR250RR, HONDA CBR250RR
No problems at all. Reliable product.
Brake, so I made the work SuKill a PRO class.
The actual difficulty of the work is about medium-low. However, do not do DIY unless you are absolutely confident.
The product is very accurate and everything worked without difficulty with Bolt On, all Bolts that hold the Bracket and Caliper in place are included.
Since we are here, we would also like to show you the Brembo caliper that we installed. Brake CaliperP4 30/40 40mm for Right Side It is. The Point of choice is “40mm Pitch” and “for Right Side”.
The hose can be installed as OEM. However, the banjo bolt requires a special brembo “1mm pitch”.
1L of DOT4-rated Brake fluid is more than enough.
View detail
สินค้าตรงปก จัดส่งรวดเร็ว View detail
Fits: HONDA GROM, HONDA Monkey125, HONDA DAX125
สินค้าคุณภาพ จัดส่งและการแพคสินค้าดีมาก View detail
Fits: KAWASAKI ZX-4R SE, KAWASAKI ZX-4RR, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R
Why so much?
It is good that it can be mounted on either the top or bottom, and it is well made, but it is disappointing that you have to shave 4mm off the circumference of the Brake Pads, so MinusPoint View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS Cafe, KAWASAKI Z900RS, KAWASAKI Z900RS Cafe
For Z900RS
To install brembo new Crab on Z900RS.
This was the only supersupport available until a short time ago.
The price is relatively high.
The air can not be vented as it is when it is subscripted, so it is necessary to use Fashion.
Downward is not dignified, and the Hose will be longer.
It can also face downward.
4 stars because it is expensive.
View detail
Fits: HONDA GROM, HONDA GROM, HONDA GROM
Might have to change.
I purchased this for the installation of the front disc on the over
So far, I've been wearing Takegawa supports.
Before attaching, I checked the actual car and found that there was no clearance.
I bought it because I thought I would have to change the support....
The thing itself is a beautiful Black with 4 bolts included.
I was able to install the disk without any problems.
View detail
Fits: HONDA GROM, HONDA GROM, HONDA GROM, HONDA MONKEY125
Will it change?
I fell in love with the look of it. lol
Just out of stock, and it took me two months to get it.
The sticker that looks like an instruction manual says to replace the pad with a new one...
What? I didn't buy it. Sweat. I feel like the outer diameter is almost the same as OEM.
Looking at the pads so far, they're a little bumpy.
I didn't buy a pad this time, so I shaved off the bumps on the pad and it was OK.
Semi-floating is chosen because full-floating is said to make noise.
I've got a Brembo 4-pot on it, and I haven't had any particular complaints so far.
In about a month, my community will finally be able to ride motorcycles.
I'm looking forward to seeing if anything feels different.
The product itself is very expensive, but it's very solid and cool.
View detail
Fits: HONDA GROM, HONDA GROM, HONDA GROM
OVER×SUNSTAR Support for Brake Disc
4,5mm thick OVER×SUNSTAR] Exclusive for Brake Disc
It will be brembo4podSupport.
And it is for JC61-75! JC92 is not available!
Please note that it is usually easy to make a mistake with Support for Rotor.
View detail
Fits: HONDA GROM, HONDA GROM, HONDA GROM, HONDA MONKEY125
FloatingRotor
Front rotor4for Hole (JC61-75)
JC92 (with Rotor5-HoleABS) Can not be installed
To bring out the performance of brembo 4pod on the grom.
The thickness of the board is 4.5mm.
This item is cheaper! (Strictly speaking, it is a little different.)
Caution! Special support is required due to the thickness of the board.
View detail
OVER RACING Disc Conversion Kit
About quality and texture be of good quality About the feeling of use I'm happy to be able to use the disk Products to buy together G-CRAFT Reserve Tank-Less Kit Type 3 Difficulty of installation I don't know what the manual is after seeing it as a picture. It took a little time to install it after taking it apart, but it wasn't difficult Cost performance and comparison with other products Disk-only backstab recommended About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing It's the product that came to mind the most in the process of converting disks Considering that there is no difference in price between disc-only and drum-only, I feel like I paid more during the disc conversion process If you're thinking about converting to a disk, I recommend using it exclusively View detail
Fits: HONDA MONKEY125, HONDA MONKEY125
a very well-made supporter
Monkey 125 has several supporters, but overracing products are of the highest quality. The finish light is excellent. It may be more expensive than other brands, but I highly recommend it. View detail
Fits: HONDA GROM, HONDA Monkey125, HONDA DAX125
Very good quality
Monkey 125 has several supporters, but overracing products are of the highest quality. The finish light is excellent. It may be more expensive than other brands, but I highly recommend it. View detail
High quality machining
I bought this for my bike project to be used with Over Racing torque rod and Over Racing swingarm designed for Kawasaki Zephyr 1100. However, I used GSX-R 1100 Rear wheel & brake disc that has 10mm less radius, so I had to replace it with suitable bracket. View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3
Cool look.
[How is it used?
About 1 week
Was the installation difficult?
it's simple
[Included Parts:were they on?
It was properly attached.
[Was there anything that disappointed you?
None in particular
View detail