Reviews
Fits: HONDA VFR800F, HONDA VFR800X, HONDA CBR600RR, HONDA CBR1000RR
Satisfied with cost-effectiveness as For RacingPad
I installed it on Circuit Running's CBR600RR (PC40 2011).
Speaking of brembo's racing pads, Z04, Z03 for endurance, and Z10 recently released are the standard, but they are expensive...
I chose the far cheaper RacingCompound (RC) since it is not used for Solidly's Race.
Before the replacement, it was a replacement from HRC (Honda's RaceParts) N615.
This was not a complaint, but the Quantity:30,000 yen for 1 Set for 1 Vehicle...
The bremboZ03 is a Quantity:40,000 yen for 1 Set for 1 Vehicle....
I was a bit worried about the price of the racing pad, which is less than half of the price of the racing pad, but brembo claims it is "for Race", so I was a bit nervous and had mixed expectations.
bremboRC is a CarbonCeramic system, which means it is not sintered.
Some people think that it has to be Sintered, but in conclusion, there was no problem.
Since the pad brand was changed, the disc surface was peeled with steel wool (Bonnstar) at the time of replacement.
Of course, when we replaced the pad, we also cleaned the Piston and replaced the DOT 5.1 Fluid. We finished it perfectly.
Here are my personal impressions after using it at Sports LandSUGO.
Control is good from the beginning to the back.
The μ at low temperatures is not extremely low, and there is no need to be conscious of heating to raise the temperature.
Even when the temperature rises, there is little change to BrakeTouch, which is a good impression (although it is also a new pad).
Low thermal strain, good strength of back plate
The surface of the disc becomes black due to the effect of heat and the carbon film.
The braking force of △ Full Brake is milder (less potent) than HRC/N615, and it would be easier if it bites a little more.
The amount of Dust powder on the Wheel is small, so it is expected to be more Life than HRC N615.
So I feel a slight difference in efficacy compared to the high price FOR RacePad, but it is a much higher dimension than OEM, and from the Balance of price and Brand reliability, I am glad I bought it.
Since the BrakeCost per pc driven drops to about half the cost, I can add that floating budget to the Tire cost.
View detail
Accuracy...
The hole where the pin goes in was distorted and needed to be scraped with a file. It is not a large problem with a little work, but if you don't have a file, you cannot install it. This is why the quality rating is so low. View detail
For the Retro Brake Overhaul
I don't know the make and model of the Brake that came with the Motorcycle, but when I rose it, I thought I could overhaul it with this kit, so I bought it.
It was a great help to be able to overhaul it beautifully!
View detail
Cheap and satisfying
I've been able to use it with no problems.
It was cheap, readily available, and satisfactory.
Since they are consumable items, it is safer to replace them regularly, so it is helpful that they are easy to buy.
View detail
Fits: KAWASAKI Ninja ZX-25R SE KRT Edition, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R, HONDA CBR250RR, YAMAHA YZF-R25
Brake's Stress is reduced.
This is a change from OEM horizontal placement 11mm to 5/8Radial master.
Because it seemed to interfere with the Switch box, the Lever was changed to Eukanaya's (NI002-049),
Nisshin's Tank Bracket (49151) for Separate Handlebars is installed.
As for the banjo fitting, a stainless steel mesh hose (AC Performance line) compatible with the car model was originally installed, but it interfered with the switch wiring, so an L-shaped adapter was used to make an escape.
My impression after installation is that the absolute braking force has not changed, but the controllability has improved.
Specifically, it is an Image with interpolated increments of braking force according to the strength of the grip.
The beginning of the grip is especially noticeable. With the horizontal 11mm pad, the rise in braking force is abrupt, but with the vertical pad, there is a sense of being able to adjust the strength of the pad. The same is true near the end of the grip, making it easier to generate strong braking force without locking.
Probably because the lever ratio and diameter are designed to match the weight of a horizontally mounted 11mm lever, it will not be that uncomfortable (too effective or too ineffective) to replace it. If you want a lighter grip or more strokes, you may want to consider a 14mm or 15mm model such as the F Land-.
In general, I can recommend it, but since it is Large strange to do banjo fitting by yourself, it is safer to ask a supply store with a Pit.
View detail
Replaced in conjunction with MAJESTY250's MASTER replacement
Both front and rear Brakes of MAJESTY250 were replaced together to reduce the difficulty of air venting when replacing the MASTER.
Material:I chose this Banjo bolt because it was the color I wanted in Aluminum.
View detail
Used to replace 20 year old deteriorated Normal hose.
Used to replace a 20 year old cracked and deteriorated Normal hose.
We chose this product because it is a vehicle-specific kit, so we did not have to worry about length, etc., and because there was a combination of black hose&banjo that matched the Matte Black car body.
The handlebar was replaced with a lower one than the normal one, and the direction of hose removal was different from the normal one because the Master Cylinder was replaced with a separate tank type of Nisshin at the same time& The length was a little long, but the problem of the length and the direction of hose removal were solved by making it so that the hose can be removed up like the normal type of off-car. The problem of length and direction of hose removal has been solved by changing the direction of hose removal to be up like the Normal type of the Off car.
After the replacement, the Touch is better and I can hang Brake with confidence.
View detail
I'd be even happier with Clip.
I changed to brembo 19RCSBrake master cylinder, so the hose is also brembo's new one.
We cut about one-fifth of the tank while exploring the interference with the Cowl and where to fix the Tank.
Being brembo's Hose, the bore is naturally moderately good.
The hose clip does not come with the lens, so I tried using a clip I had on hand and found that a DAYTONA clip with an inner diameter of 10mm was a perfect fit. (11mm, maybe, or...?)
I used it with a good amount of bending, not to say 90-degrees, but I did not feel any particular strain on the hose and felt it was soft.
I appreciate the low price for the HoseSingle Body, but it would have been nice if the Hose clip was also included so I wouldn't have to go through the trouble of researching and buying one.
View detail
Fits: DUCATI DESERTX, DUCATI HYPERMOTARD 1100, DUCATI HYPERMOTARD 1100S, DUCATI HYPERMOTARD 1100EVO, DUCATI DIAVEL 1260S, DUCATI HYPERMOTARD 796, DUCATI HYPERMOTARD 821, DUCATI HYPERMOTARD 939, DUCATI HYPERMOTARD SP, DUCATI HYPERMOTARD 950, DUCATI HYPERMOTARD 950 SP, DUCATI HYPERMOTARD 950 RVE, DUCATI HYPERSTRADA 821, DUCATI HYPERSTRADA 939, DUCATI MONSTER 400, DUCATI MONSTER 620, DUCATI MONSTER 695, DUCATI MONSTER 1000, DUCATI MONSTER 696, DUCATI MONSTER 750
Attachment
As expected. Thank you very much. View detail
Fits: HARLEY-DAVIDSON OEM Type HandlebarControl
I was able to exchange easily and have a good feeling about it.
Wiring connection is troublesome because it requires a solder, so it would have been nice to have something like a crimp terminal. View detail
Fits: YAMAHA MAXAM [Magzam] (SG17J/SG21J)
MAXAMFront wheel Disc Rotor
When I got the MAXAMFront wheel and tried to install it on MAJESTYC, I realized that the MAJESTY and MAXAM discs were not compatible, so I had to order one in a hurry.
I chose it for availability and price because I don't think there is any need to be concerned about OEM for a street-use scooter.
The entire DISC is still machined, so discoloration around the hub is a future concern.
View detail
Fits: その他 For import type calipers (BREMBO [Brembo] common for racing and street)
10mm diagonal is helpful.
AP racing's NORMALBreeder has rusted badly, so we replaced it. The size is 11mm diagonal, which is very rare in FOR JAPAN MODEL, so now we can use 10mm Spanner Glasses instead of MONKEY Wrench, which improves the workability. I'm satisfied with the new size.
This is a RECOMMENDATION because it is definitely easier to use than the NORMAL with the Breeder still at 11mm.
View detail
Fits: YAMAHA TRACER9 GT, HONDA CB1100EX, HONDA CB1100EX E Package, HONDA CB1100BLACK STYLE, HONDA CB1100, HONDA CB400SF, HONDA CB400SB, HONDA VTR1000SP-1, YAMAHA FAZER8, HONDA CRF1100L Africa Twin Adventure Sports, HONDA CB1100, HONDA CB1100 typeII, HONDA CB1100 typeII, HONDA CB1100 typeI, HONDA CB1100 typeI, HONDA CB1000SF, HONDA CB1000SF-T2, SUZUKI BANDIT1200 S, SUZUKI V-STROM1000, SUZUKI SV1000
Replace Red with Golden Pad
I have not been able to drive yet because of the rain, but I changed the pad as well as the Caliper OH!
I'm looking forward to running it. ('∀ `)
View detail
Fits: HONDA CB400SF HYPER VTEC SpecIII, HONDA CB400SF HYPER VTEC SpecII, HONDA CB400SF HYPER VTEC Revo, HONDA CB400SF, HONDA CB400SB, HONDA CB400SB, HONDA CB1300SUPER BOLD'OR, HONDA CB1300SUPER FOUR, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300SF, HONDA CB1300SB, HONDA CB1300SB, HONDA CB1300SB, HONDA CB1100EX, HONDA CB1100EX, HONDA CB1100EX E Package, HONDA CB1100EX BLACK STYLE, HONDA CB1100BLACK STYLE
Nice...
I replaced it with a Sintered pad because the Brake squeal would not go away and it was less expensive and seemed more durable.
The pad before replacement came with an unknown manufacturer, so there is no comparison, but it works and does not squeal as usual. 。
Control is much better than I expected, and the effectiveness changes with the amount of force.
It seems to be a bit aggressive to Rotor, which is a concern, but it was a good decision to replace it.
View detail
Fits: HONDA CBF1000, HONDA NC700X, HONDA NC700SXL TYPE LD, HONDA NC700S, HONDA CBR250R, HONDA CBR250R, HONDA CBR1000F, HONDA CB650F, HONDA CB500 F, HONDA CB400X, HONDA CB400SF Ver R, HONDA CB400FA, HONDA CB400F, YAMAHA WR250X, TRIUMPH Tiger 800XC, TRIUMPH Tiger 800, TRIUMPH Thruxton 900, TRIUMPH Thruxton 865, TRIUMPH Street Twin 900, TRIUMPH Scrambler 865
Brake to JackKnife if you apply it strongly ".
This was the first time for me to use the Metal pad, but I have the impression that it works harder than the previous Golden pad.
I grabbed Lever with my usual BrakePoint and it worked so well that I JackKnife'd it unexpectedly.
We are still waiting to confirm the durability of the product, but as for the effectiveness, we are satisfied with it.
View detail
Clean. Dirty. Vivid.
Description used only in DOT 4.0 and 5.1.
5.0 (Silicon-based) not used
[How is it used?
Continuous use from July 18, 2021 to April 21, 2024
・71,299 - 59,896 = 11,403km
Urban, Touring, and Circuit driving events
YZF-R6Front side
Master Cylinder side is R6OEM
Fluid tanks are available from Kawasaki (https://www.webike.net/sd/21984592/)
I think Clamp was something from K-CON.
Fluid Transparent DOT5.1 (https://www.webike.net/sd/24515708/)
FluidBlue (https://www.webike.net/sd/24038239/)
FluidGreen (https://www.webike.net/sd/20443936/)
FluidRed (https://www.webike.net/sd/21585702/)
Was the one you received as per Image?
As per Image with Simple Package, first found in Naps and now also in LycoLand.
Was the installation difficult?
The hose itself is fairly easy to insert after loosening the clamp and removing the original hose by tearing it open. However, it is a little bit large to insert the hose without wetting the inside of the hose with Fluid or something.
Air venting is required for modification of the brake system, so there is some time and effort required to vent the air.
How was your experience with it?
・ [Color] When we say ClearTank. [Color] Unlike the Smoke Fluid Tanks, it is completely [Color] Clear shows the Fluid color beautifully.
Although the Image was less durable than the Black Hose, it is still in use with no rips, cracks, or tears.
The Fluid is not blotchy like the non Fluid-compatible Hose, which was my biggest concern, and the word "Fluid-compatible" is true.
The color of the Fluid is so clear that the yellow tint of the Fluid is very obvious.
Especially with blue Fluid, it takes less than a year for the color to become the color of Tokyo Bay, although it is beautiful immediately after the replacement. (Replaced more than 4 times in 3 years of use)
The transparent design makes it easy to see the climb when injecting from the Caliper side.
The product is relatively new, so even Motorcycle shop owners are not familiar with it. Is this Fluid-enabled?" The situation arose where people asked me "What do you mean?
The feeling of operation cannot be evaluated independently because the Fluid is being replaced at the same time, but I am sure there will be no problem because I can use it without feeling any discomfort.
The Red was probably too bright a red to match the Blue/Silver Motorcycle, and I didn't have a picture of it because I replaced it too quickly.
[Included Parts:were they on?
Hose only, Clamp not included
[Was there anything that disappointed you?
None, as the Fluid colors are nicely recognizable and the durability and feel of the product are absolutely fine.
Although it was unexpected that the discoloration caused by Fluid degradation was too obvious, it is inextricably linked to the desire to clearly distinguish the color of Fluid.
[ITEMS TO BUY TOGETHER
Hose clamp and for ReplacementFluid
DAYTONA's Black Clamp rusted quickly, so K-CON is recommended.
The price is not that different from Black's Hose, and the feel is perfectly acceptable. The increase in replacement frequency due to appearance is not a bad thing when it comes to performance.
Degradation of Fluid [Color] A fun product to add to your selection if you can accept that it is more sensitive than ClearTank.
View detail
Touch may be too soft.
Inconvenient because the 10R OEMBrake cannot be removed without removing the Wheel.
Mounted on the underside with Bracket to improve serviceability.
The pad spring is very hard and the pad pin is press-fit, so we replaced it with an external pad spring and pin.
If you are a do-it-yourself maintenance person and use the new Crab, the above should be changed.
Even if you purchase the above, I think the price is low for an Aluminum Piston with high corrosion resistance and a pad.
The 30mm→34mmPiston changes the Ratio and the Pedal is very squishy.
10ROEMMASTER is 14Φ and there is nothing I can do about it because there is no MASTER that is any more LARGER, it should have been a 32mmPiston.
View detail
The glossiness is different from Fitting.
The company's Black fitting has a glossy texture, but this one is matte.
I would like to see it unified with Matte.
I tightened it with 20N, but it is stainless steel, so it is firm and secure.
View detail
Too bad about the color of Nut.
Purchased because the diameter of the Nipple no longer fit in the MASTER replacement.
Same shape as 10ROEM but OEM is 8mm diameter with domestic Spec. and this is 7mm diameter with RCS Nipple.
I thought they were the same except for the diameter, but the fixed nut on the lid is silver while the OEM's is black.
It's a fewmm of Nut, but it's a shame that it looks like it's floating when I wanted to create a unified look with Black.
I tried to replace it, but it is fitted like a ring of wisdom and cannot be removed.
View detail
Compact
Used 635mm on ZX10R (19) to install new Crab, just the right length.
The structure is simpler and more compact than the Edge line, which was previously used.
The Crimp section is shorter than the SuEdge for easy handling.
However, the Black part is shiny and not good, so I might have preferred the normal Stainless.
The texture of BlackStainless and the MachineMachine-like appearance of the Edge are better, but I have heard rumors that it leaks a lot.
If I had to choose by functionality, it would be Goodridge.
View detail