Reviews
Repeater
I replaced the old one with an aging one, and I put it where it didn't belong. View detail
Fits: YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA MT-03, YAMAHA YZF-R25
It looks better now.
Model YZF-R25
The Rear is quite dirty and it is now clean. the Brake Caliper is OEM and the Pad is DAYTONA, but I am glad I replaced it. The braking power is normally increased and I am satisfied.
View detail
Required for Master Hose replacement
[How is it used?
Purchased a new Master Cylinder with the replacement of the old one.
The OEMHose is a little short, so if you use an external master like brembo or GALE SPEED, it is not long enough, but if you use an extended VERSIONBolt, you can use it as is somehow, but the angle is a limit, so it could crack and break at any time.
Large front brake, so do not let your guard down!
Was the one you received as per Image?
Usual quality
I don't think there is any other manufacturer that offers this kind of product except Active.
This is a great product, you don't have to replace the entire hose, which saves you money!
Was the installation difficult?
Can be difficult if you're a beginner.
When removing the hose, be careful not to spill the Fluid!
If you put it somewhere, it will discolor or corrode quickly, so please prepare water before proceeding.
How was your experience with it?
as expected (as opposed to expected)
With this, you can change the Hose from MASTER to HOSE at will.
[Included Parts:were they on?
No, sir.
[Was there anything that disappointed you?
I don't have it, but if it were a little cheaper...
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Clean. Dirty. Vivid.
Description used only in DOT 4.0 and 5.1.
5.0 (Silicon-based) not used
[How is it used?
Continuous use from July 18, 2021 to April 21, 2024
・71,299 - 59,896 = 11,403km
Urban, Touring, and Circuit driving events
YZF-R6Front side
Master Cylinder side is R6OEM
Fluid tanks are available from Kawasaki (https://www.webike.net/sd/21984592/)
I think Clamp was something from K-CON.
Fluid Transparent DOT5.1 (https://www.webike.net/sd/24515708/)
FluidBlue (https://www.webike.net/sd/24038239/)
FluidGreen (https://www.webike.net/sd/20443936/)
FluidRed (https://www.webike.net/sd/21585702/)
Was the one you received as per Image?
As per Image with Simple Package, first found in Naps and now also in LycoLand.
Was the installation difficult?
The hose itself is fairly easy to insert after loosening the clamp and removing the original hose by tearing it open. However, it is a little bit large to insert the hose without wetting the inside of the hose with Fluid or something.
Air venting is required for modification of the brake system, so there is some time and effort required to vent the air.
How was your experience with it?
・ [Color] When we say ClearTank. [Color] Unlike the Smoke Fluid Tanks, it is completely [Color] Clear shows the Fluid color beautifully.
Although the Image was less durable than the Black Hose, it is still in use with no rips, cracks, or tears.
The Fluid is not blotchy like the non Fluid-compatible Hose, which was my biggest concern, and the word "Fluid-compatible" is true.
The color of the Fluid is so clear that the yellow tint of the Fluid is very obvious.
Especially with blue Fluid, it takes less than a year for the color to become the color of Tokyo Bay, although it is beautiful immediately after the replacement. (Replaced more than 4 times in 3 years of use)
The transparent design makes it easy to see the climb when injecting from the Caliper side.
The product is relatively new, so even Motorcycle shop owners are not familiar with it. Is this Fluid-enabled?" The situation arose where people asked me "What do you mean?
The feeling of operation cannot be evaluated independently because the Fluid is being replaced at the same time, but I am sure there will be no problem because I can use it without feeling any discomfort.
The Red was probably too bright a red to match the Blue/Silver Motorcycle, and I didn't have a picture of it because I replaced it too quickly.
[Included Parts:were they on?
Hose only, Clamp not included
[Was there anything that disappointed you?
None, as the Fluid colors are nicely recognizable and the durability and feel of the product are absolutely fine.
Although it was unexpected that the discoloration caused by Fluid degradation was too obvious, it is inextricably linked to the desire to clearly distinguish the color of Fluid.
[ITEMS TO BUY TOGETHER
Hose clamp and for ReplacementFluid
DAYTONA's Black Clamp rusted quickly, so K-CON is recommended.
The price is not that different from Black's Hose, and the feel is perfectly acceptable. The increase in replacement frequency due to appearance is not a bad thing when it comes to performance.
Degradation of Fluid [Color] A fun product to add to your selection if you can accept that it is more sensitive than ClearTank.
View detail
MASTER.
[How is it used?
Purchased a new OEM hose because it is not long enough to replace the Master Cylinder.
The OEMHose is a little short, so if you use an external master like brembo or GALE SPEED, it is not long enough, but if you use an extended VERSIONBolt, you can use it as is somehow, but the angle is a limit, so it could crack and break at any time.
Large front brake, so do not let your guard down!
Was the one you received as per Image?
Usual quality
At first I think it's made in Japan, but when I looked it up, it's a United Kingdom brand, so it's full of luxury!
Stickers are also included in the package, so you can quickly attach them to the car body!
Was the installation difficult?
Can be difficult if you're a beginner.
When removing the hose, be careful not to spill the Fluid!
If you put it somewhere, it will discolor or corrode quickly, so please prepare water before proceeding.
How was your experience with it?
as expected (as opposed to expected)
Soft and easy to angle
Nothing in particular that I think is wrong.
Just for reference.
Master Cylinder:GALE SPEEDVRC
Hose length:I bought 285mm, but when I installed it, 260mm is also enough, so I recommend 260mm.
In line with this, Active's Flare block adapter" should also be purchased in conjunction with the required
[Included Parts:were they on?
Sticker
[Was there anything that disappointed you?
I don't have it!
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
VERSIONBolt is not included.
View detail
Impulse purchases that were not planned
What made you decide to buy?
I bought it elsewhere, half on impulse. (Lol)
[How is it used?
This is a change from PLOTbrembo Stainless SteelCaliper Mount Bolt.
[How was the installation?
Titanium has the Merit of being lighter than Steel. However, it is necessary to apply ThreadGrease to each bolt and tighten it. If you omit or forget to apply ThreadGrease, the screws will stick, resulting in a large risk of damage to the bolts.
[How was it when you used it?
The OEM CaliperMouthBolt is 62mm long and 44g, the PLOTbrembo Stainless SteelCaliper Mount Bolt is 70mm long and 55g, the Zita Titaniumium Caliper Mount Bolt is 70mm long and 26g, 18 PLOTMount BoltQuantity:The 2pcs were enough for one Zita Titaniumium Bolt, contributing to a slight weight reduction.
View detail
Compact
Used 635mm on ZX10R (19) to install new Crab, just the right length.
The structure is simpler and more compact than the Edge line, which was previously used.
The Crimp section is shorter than the SuEdge for easy handling.
However, the Black part is shiny and not good, so I might have preferred the normal Stainless.
The texture of BlackStainless and the MachineMachine-like appearance of the Edge are better, but I have heard rumors that it leaks a lot.
If I had to choose by functionality, it would be Goodridge.
View detail
Fits: KAWASAKI ZX-10R
Pad position is subtle
Inconvenient because the 10R OEMBrake cannot be removed without removing the Wheel.
Purchased to improve serviceability by underlining.
ABSFlareBlock, Hose (635mm), Fitting (20°), Mount Bolt (M8*20) are required for installation.
The swing arm needs to be removed when wiring, so it is quite large.
I used it on a new Crab, but the pad sticks out, so I had to shave about 5mm off.
I was able to do this in about 5 minutes because I had Leutor and TungstenBit, but if you only have File, this is also Large strange.
Weight is Quantity for Bracket and Caliper:It was almost the same as OEM with Set.
The design of the cutting groove was uneven (white spots) and the texture was not good. (The texture was not so good, but the others were good.
View detail
Touch may be too soft.
Inconvenient because the 10R OEMBrake cannot be removed without removing the Wheel.
Mounted on the underside with Bracket to improve serviceability.
The pad spring is very hard and the pad pin is press-fit, so we replaced it with an external pad spring and pin.
If you are a do-it-yourself maintenance person and use the new Crab, the above should be changed.
Even if you purchase the above, I think the price is low for an Aluminum Piston with high corrosion resistance and a pad.
The 30mm→34mmPiston changes the Ratio and the Pedal is very squishy.
10ROEMMASTER is 14Φ and there is nothing I can do about it because there is no MASTER that is any more LARGER, it should have been a 32mmPiston.
View detail
Essential items for vehicles with external exhaust system replacement
After replacing the Tornado Exhaust System with Mukawa's Tornado Exhaust System, the Master Cylinder of the Rear brake stood out. I didn't like the whitish look of the Master Cylinder, so I covered it up with a Master cupCover. It looks good. View detail
The glossiness is different from Fitting.
The company's Black fitting has a glossy texture, but this one is matte.
I would like to see it unified with Matte.
I tightened it with 20N, but it is stainless steel, so it is firm and secure.
View detail
Relax with Stainless Steel
20° for new Crab installation.
Aluminum is the only choice for Stainless because it cracks.
It is surprisingly shiny, so I would like something with a matte texture from Hairlineetc.
View detail
Too bad about the color of Nut.
Purchased because the diameter of the Nipple no longer fit in the MASTER replacement.
Same shape as 10ROEM but OEM is 8mm diameter with domestic Spec. and this is 7mm diameter with RCS Nipple.
I thought they were the same except for the diameter, but the fixed nut on the lid is silver while the OEM's is black.
It's a fewmm of Nut, but it's a shame that it looks like it's floating when I wanted to create a unified look with Black.
I tried to replace it, but it is fitted like a ring of wisdom and cannot be removed.
View detail
Fits: KAWASAKI ZRX1200S, KAWASAKI ZRX1200R, KAWASAKI ZRX1100
Exactly
As expected from a car model! Everything was just fit!
I could see the difference from FirstTouch even with Normal caliper.
View detail
Clutch becomes lighter
I installed it on New Model GSX1300R HAYABUSA.
In fact, this time we are replacing VRD, also by GALE SPEED. replacing VRD to VRC from higher MODEL to Standard model may sound strange, but there are actually various reasons.
First of all, I was attracted to this VRC the moment I received it and opened the box. It looks like a work of art indeed, and just looking at it raised my Tension and made me feel that it was worth the high price.
I think it beats bremboRCS just for the smooth surface treatment. To be honest, I don't understand why brembo's RCS is so popular. I used to be a brembo RCS fan, and I used to think that no matter what kind of motorcycle I switched to, I would first replace it with brembo's RCSMASTER.
However, I felt the quality of brembo's forging was not worth the price. I was tired of that, so I chose GALE SPEED's Vine VRC this time.
Back to the story, I first went for the VRE feel and went for the bright black VRD for Cost considerations, but I quickly gave it up and went with this VRC because it looks like RCS and I felt something was wrong with it. I am usually a Touring Maine, so I can't tell the difference between VRD and VRC! Still, I chose it because of the way it looked. If that's what you enjoy, then that's fine.
Finally, after installing it and running it for a bit, it feels very good - lighter than the OEMClutch, and a little bit better at 17.5mm.
※※※※ Note ※※※※
New Model GSX1300R HAYABUSA will change the clutch master, [Hill HoldControlSystem will not be available.
The reason is that with the OEM clutch switch, if the clutch is released for a moment, the switch returns, the ECU recognizes that the car is starting, and the rear brake is released. However, with the external clutch master, the switch remains pressed until all the clutch is released, so the car is not detected as starting, the rear brake remains on, and even if the Axel is turned, the car does not move forward! This is very dangerous. I would like to see any Manufacturer solve this!
↑ It may be a little confusing, but try it yourself, it will never start!
In my case, I have turned that function off.
View detail
Left Side also
Purchased this one along with a Front caliper replacement for a New Model GSX1300R HAYABUSA.
Quantity:Pair (for Left and Right) Quantity:I purchased 2pcs and here is the Left Side imprint.
The OEM was not long enough and the angle of the VERSIONBolt was different, so it had to be replaced.
However, it is not just a Hose replacement that can be used.
Caliper needs to be replaced→Hose needs to be replaced→Flare block adapter also needs to be replaced
A series of "↑" gold-dropping flows are required lol.
The old GSX1300R HAYABUSA does not have ABS, so as long as the hose from the master cylinder is replaced, it can be used as is,
For the New Model, the handling of the FrontHose has changed.
Apart from the hose from the Master Cylinder, there is a Gold hose from the ABS modulator and a Quantity hose from the ABS modulator.:2pc divided.
Therefore, first of all Flare bu Lock adapter. must be purchased.
・ Flare bu Lock adapter. https://www.webike.net/sd/24651726/Part No. FM10AN3T
Next, does the length vary by Caliper? I think they're probably the same, so here's a reference.
・Quantity:Length without 2pc Hose and Versionbolt:335mm*Quantity:2pc
But Hose alone is definitely not enough, so I purchased several Adapters below together in my case.
・https://www.webike.net/sd/1540510/ [Brake Fitting Adapter]. M10→AN3/8*2 for Caliper
45 degree Adapter
Well, there is not much information on the New Model GSX1300R HAYABUSA, so you will never know unless you try it yourself, but if you fail, your Gold will be wasted, so I will tell you everything I know and hope you will find it useful.
Next, I was a bit attracted to this product itself, especially since it has a Yellow color Tag?
Accuracy is not bad, but Quantity:I bought 2pcs, and one of them was leaking Fluid from the joint when pressure was applied, even if I tightened it from the beginning. But when I tightened it firmly one more time, it stopped leaking. I think it was because I didn't tighten it all the way to the back from the beginning after all. It has nothing to do with the quality of the product!
View detail
I'm glad I went with VRC.
I purchased this VRC when I replaced my GSX1300R HAYABUSA with a MASTER. In fact, this time, it is a replacement from VRD, also by GALE SPEED. replacing VRD to VRC from higher MODEL to Standard model may sound strange, but there are actually various reasons.
First of all, I was attracted to this VRC the moment I received it and opened the box. It looks like a work of art indeed, and just looking at it raised my Tension and made me feel that it was worth the high price.
I think it beats bremboRCS just for the smooth surface treatment. To be honest, I don't understand why brembo's RCS is so popular. I used to be a brembo RCS fan, and I used to think that no matter what kind of motorcycle I switched to, I would first replace it with brembo's RCSMASTER.
However, I felt the quality of brembo's forging was not worth the price. I was tired of that, so I chose GALE SPEED's Vine VRC this time.
Back to the story, I first went for the VRE feel and went for the bright black VRD for Cost considerations, but I quickly gave it up and went with this VRC because it looks like RCS and I felt something was wrong with it. I am usually a Touring Maine, so I can't tell the difference between VRD and VRC! Still, I had to choose based on looks.
Finally, after installing it and running it for a bit, it feels very good, I feel the VRC is sufficient, I don't really need VRD or VRE except for Race.
We recommend this VRC over RCS! You will never regret it!
View detail
Body color and Match
The CylinderTank cap and the body color match each other very well. View detail
I like that it's already processed.
I bought it because it is already machined for Casting wheel. View detail
Many color variations available
A wide variety of color variations are available, making it easy to match the color of the car body.
The price was inexpensive and helpful.
The texture is perfect.
View detail