Reviews
Effectiveness is good, glad I bought it.
[How is it used?
Exhaust System of Z900RS was replaced and Silencer was Bullet Silencer by K-FACTORY.
The kit came with two baffles, one for the outlet and one for the inlet, and the combination of the two was supposed to allow adjustment of volume and exhaust pressure.
When the outlet type was installed, it sounded like a large dump exhaust system and I could not bring myself to use it. The exhaust resistance of the inlet type was too large and the volume went down a little, but at mid-speed or higher, the exhaust clogged and the large width performance went down.
So, I thought there must be a way to lower the volume while maintaining a reasonable exhaust resistance, so I used this product.
Was the one you received as per Image?
As per Image as I had seen the actual product at the store.
Was the installation difficult?
There is no difficulty if you choose a Size that fits within the inside diameter of Silencer.
However, the Silencer exit diameter is 55Φ for use with Bullet Silencer,
The inside of the punching pipe had to be 45Φ so it was necessary to fill the 10mm gap at the exit.
I looked for a gasket that would fit, but could not find one, so I wrapped a heat-resistant aluminum tape around it.
Also, the Silencer fixing bolt that came with the kit was a retro black ordinary Hexagon bolt, so I used a silver cap bolt that I had on hand.
How was your experience with it?
The volume did not go down as much as I had hoped, but at the moment of startup without any Absolutely not!" The explosion was so loud that it felt like "I know it's annoying, but can you forgive Limit?" This was the Level that
Unlike the Silencer-attached baffle, the Straight structure is maintained, so exhaust resistance is not increased excessively, and the sound quality is not muddy and high-frequency components seem to be suppressed.
In terms of performance, it is not too much at low speeds, but it is not too much at high rpm, and it is not too much at high rpm.
However, the Bullet Silencer, which I almost gave up using because it was too noisy even though I like the look of Large, is now available, and the Silencer is also black and retractable, so it is unobtrusive and I am glad I purchased it.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
It would have been nice if the volume could have been a little lower, but then it would have been a poof clogging.
Once again, I felt that the OEM Exhaust System is well made.
View detail
Muffled replacement available
There is a muffled replacement and you can hear the bass well. View detail
Cosy! Sound deadening effect, of course.
[How is it used?
Used for cbr600rr. For muffling the sound of external Exhaust System.
Was the one you received as per Image?
Street Image
Was the installation difficult?
Drilling holes in the Pipe for installation was Large strange.
I am sure it is a Type that can only be attached to Exhaust End.
How was your experience with it?
It muffles the sound a bit, but it is still loud.
[Included Parts:were they on?
[Was there anything that disappointed you?
View detail
KERKERMegaphone on the Inner silencer.
The inner diameter of the pipe after the assembly part of the KERKERMegaphone installed on a Z650 is Φ60, so I bought it to use as an inner silencer for vehicle inspection. The proximity noise level when installed as it is is about 97-99dB using a noise measurement application. How reliable is the app? But I wanted to muffle the sound a little more, so I stuffed Glass Wool inside the punching pipe.
In this state, it is now 95-97 dB, so for now, the car will be inspected with this.
I had hoped for a more muffled sound, but the StraightPunching pipe did not produce the Large effect I had hoped for.
View detail
Replacement
I bought it to replace it as it became RustRust
It's neither too little nor too much, and it's easy to install
The dimensions must be measured properly
View detail
It's just that the volume will be lowered, but..
Motorcycle：KLX125
Exhaust System：OVER Stainless Steel Carbon Exhaust System
History
KLX125 OEMExhaust System sounds too small to notice the automobile I couldn't get it, so I changed it to the Full Exhaust System of OVER, and I had a dangerous experience rarr;End It became an annoying sound explosion even with Baffle, so Inner Consider purchasing a silencer
?attachment
Because the end shape of the Silencer is not straight, it is called the exhaust pipe and Mounted between Silencer
(It's only held in place by the momentum of the exhaust rather than mounting, so if you give it a shock, it will move )
Good points
The sound of the external exhaust system's single-cylinder sound, like a group of half-greater cylinders, is not too loud Became sound enough to Appeal the presence in the automobile
It's cost effective in terms of ensuring that the volume is reduced
Bad points
After about a month of use, I found out that the rust was on the large..
Stainless steel is still the best inner silencer
View detail
There is a certain amount of sound deadening effect
This is for the external exhaust system on my Harley
Glass Wool of thinness is rolled from the beginning, but when I use it, I will use it as well as one roll of Glass I added the Wool and then inserted it
Without Inner silencer, the regulation volume is lightly exceeded, but it is 94db when installed The volume dropped to
View detail
Normal
Bought it to reduce the sound for my custom made Yamaha sr400 exhaust,it will silent the sound at lower rpm range of my exhaust but Doesn't work at higher rpm range the sound note would become even fatiguing,I guess this is subjective for different exhaust. View detail
With silencing effect
Added to XL 1200 C SPORTSTER 1200 External Exhaust System.
Buy this item whose inner diameter is the closest.
The cotton part is hard and hard, it will silently sound.
Because the exhaust pressure of Motorcycle is high, cotton became a mosaumosa in a relatively short time.
Although it is not currently used, I think that it is effective when lowering the volume of Exhaust System at the time of vehicle inspection
View detail
It has an effect
I used it for the XL 1200 C SPORTSTER 1200 Exhaust System.
Exhaust System was a sharp exhaust sound near the straight pipe outside the company,
After installation, the sharpness of the sound calmed down, and it became a slightly muffled sound.
It is an impression that the sound is rounded.
I think that the volume was also suppressed and it was effective enough
View detail
Muffler effect perfectly
Since the Other Company Product Expression System of CRF 230 F was a bit of explosion to run on the public road, we installed the Inner silencer.
Because it is a Universal Product, we need some ingenuity, but the effect is outstanding.
It's not too quiet, it's too noisy.
I can recommend it..
View detail
Large satisfied
I attached it to Slash Cut Exhaust System of VIRAGO 250.
Easy to install, it became a very nice sound.
As my feeling, it sounds like I made the sound of a straight pipe purely Small.
The power of the sound has increased with a little expense and I am very happy.
View detail
Igie RidersSLASH Longo Exhaust System perfect!
Today, with the expectation put in! Because it was a straight tube Thunder sound! Personally OK but purchase determination with a neighborhood inconvenience! Size is also 47 Pitari! - - - Kashakasha sound of treble disappears! Potato Potetchi at low temperature ♪ (Harley of the 1970s) It is a good sound! I breathe in the middle until the engine warms ♪ This is also good! Very good so I will order additional order.
Sound is also Large - - - Compared to explosion! Although the inspection may be Gili, the high speed will also extend!
View detail
Attached to Python 3 Slip-on Silencer
I used Python 3 Slip-on Silencer for FXDL, but I was bothered by explosion. When installing this KIJIMA 's Inner Silencer Deluxe, the silencing effect is wonderful. The sound quality is also good.. Problem solving (^^). View detail
"07 years Injection vehicle. I was annoyed by the badness of the throttle response of a normal muffler, and a feeling of excrement, and I decided on muffler exchange. I chose cycle shack of 2.5IN.(it was equipped with a same baffle as SE2) However ... sou
"07 years Injection vehicle. I was annoyed by the badness of the throttle response of a normal muffler, and a feeling of excrement, and I decided on muffler exchange. I chose cycle shack of 2.5IN.(it was equipped with a same baffle as SE2) However ... sound volume is so loud and I cannot start engine in the residential street at daytime and it is further embarrassment ... It was replaced in the press wool type. Although I cannot say it becomes quiet, I can realize a sound deadening effect certainly. It is the sound I can apply engine in the garden, (limited to daytime) and the depth, such as the large displacement vehicles do not go out there deep bass, one shot of the plosive is emphasized, and good feelings are increased. The throttle response was also finished on the perfect level. If it shifts to the higher gear at the time of a low speed, a little axel is opened and it is made feeling, a feeling of a beat and sound appropriate for a harley can be enjoyed fully." View detail
It is an ordinary inner silencer. Since it is consumable goods, cheap one is good. Of course, silence is also O. Be careful of a size in the case of purchase.
It is an ordinary inner silencer.
Since it is consumable goods, cheap one is good.
Of course, silence is also O.
Be careful of a size in the case of purchase.
View detail
an auction -- the straight pipe short muffler purchase of a silencer-less one-off!! It equips and puffs an axel... it gets -- ~ being and purchasing an inner silencer by x. it is determination from a muffler inside diameter and the die length with whi
an auction -- the straight pipe short muffler purchase of a silencer-less one-off!! It equips and puffs an axel... it gets -- ~ being and purchasing an inner silencer by x.
it is determination from a muffler inside diameter and the die length with which it can equip to this product!! Attach immediately... CHITO -- since it is a we bit bad old man although it is noisy -- OK.
.
.
In order to unite with a muffler inside diameter when attaching, some processing is required, but a price is also handy and four stars.
View detail
Although it had equipped with the custom muffler almost near a straight pipe, the nuisance to the neighbors was considered and purchased. As operative, although it does not become precocious, it becomes abbreviation half [ of the state of a straight p
Although it had equipped with the custom muffler almost near a straight pipe, the nuisance to the neighbors was considered and purchased.
As operative, although it does not become precocious, it becomes abbreviation half [ of the state of a straight pipe ], and a high sound with sufficient normal in which tone quality also bursts disappears, and sound volume becomes crisp touch, and is large satisfaction.
It is the good touch which adjusts the grade sound volume which is the quantity of glass wool.
Muffler sound can be enjoyed now, without seldom caring about a nuisance to the neighbors.
However, about attachment, it was fairly troublesome.
Since this product is made more greatly about 1 mm than a notation size for exhaust leakage prevention, it does not enter, unless it will delete the outer circumference of a fixed portion, if an apt size is purchased.
Although I used the grinder, I think that it becomes fairly serious work in case of manual operation.
And since just it has worries about exhaust leakage when becoming distorted, the way which purchased the size smaller than a size needed from the beginning, and filled the crevice with the gasket may be comfort.
View detail