Reviews
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
Good quality and sound from minimoto.
I have two of these pipes. I use them on 1969 k1 rigid framed with 108cc stroker kits. They sound good without the baffle and not too loud. Bike runs great with them. The finish and fit is very high quality. Polished nicely. Beautiful welds. View detail
Necessary and sufficient performance
The engine side mounting screws are difficult to remove without removing the UnderBracket and other parts. Other than that, the Large is strong enough for anyone. The performance of Large and Single4Stroke engines' exhaust systems are all similar. Silencer and exhaust pipe made of steel are impossible. There, the high price by name makes me doubt the thinking of those who buy them. As I mentioned earlier, two horsepower and three horsepower are no different. It is definitely better than rusting. As for the volume, it is not noisy at Idling and is at a level that is not a problem. It is not so loud at high rpm, but I don't think it is noisy. 100km is enough with the meter reading of ct125. Fuel consumption is not much different from NORMAL. If the one you put on is worse than NORMAL, please re-educate the Right hand. View detail
Fits: HONDA MONKEY
OEM Type Exhaust System
I am satisfied with Large at this price!
The texture is just fine.
View detail
Fits: HONDA MONKEY
MINIMOTO MONKEY TYPE C STD Exhaust System Φ28mm Chromium Plating
Acquired for Honda Monkey. It's been a long time since I've thought about replacing the muffler. MINIMOTO liked the exterior (a huge plus in similarity to the original muffler). There are minor questions about lacquer treatment, but overall everything is very kind. I was delighted with the completeness, the whole range of necessary metizas and gaskets. The installation went perfectly (I think even the schoolboy will manage). And to the question of sound - it is beautiful, light and soft bass. I'm happy with the result, sorry I couldn't find a similar offer for the second moped (Honda Little Cub)... View detail
Fits: HONDA MONKEY, HONDA GORILLA (12V) Z50J-2000001-, HONDA GORILLA (12V) AB27-1000001-, HONDA MONKEY(12V) Z50J-2000001-, HONDA MONKEY(12V) AB27-1000001-, HONDA GORILLA2.6PS(6V), HONDA GORILLA3.1PS(6V), HONDA MONKEY2.6PS(6V), HONDA MONKEY3.1PS(6V)
Sound is Large
Personally, I was expecting the sound to be a bit louder than the NORMAL, but there was not much change. If you live in a residential area, it may be just right.
Also, please note that the NORMAL exhaust guard will attach to the silencer part, but not the other parts (there is no bolt on the exhaust system side to attach it). I like the Forme without the Exhaust Guard, so I have no problem with it.
View detail
Great price for a high quality unit
One of the cheapest exhausts for the ct125 with a great quality finish and welds, I'm decently surprised. Pretty quiet too, for louder enthusiasts, you can remove the end baffle which will definitely make it a bit more loud. 9/10 View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA
Original type exhaust for monkey - cheap and good
This exhaust was under my honda monkey z50k3 minitrail. Cheap exhaust that fits perfectly. Can't say much about it, does what it has to do for a good price. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA
I'm all about quiet, and this is the only way.
I use it on my DAYTONA 88cc.
By sacrificing performance, it achieves a volume that is slightly Larger than OEM. This is a product that will not bother your neighbors.
The Exhaust System is made at the lowest level and can not be installed with the included collar.
View detail
Fits: HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY
All lies.
Anyway, the welds are so bad that even compatible models can't be pimped out, and it interferes with the rear suspension, and the angle of the inserts on the engine side don't match, so I'm just laughing. (Lol) If you buy this, you must have both Hand Bent on the Engine side and Hand Bent on the Silencer side. I can't get the Hand Bent so I'm using only one side of the Bolt on the Engine side and forcing the back of the Bolt to be spread outward, but I'm not sure if the back of the Bolt can handle the exhaust leaks and the impact of driving. I really wish I hadn't bought it. View detail
Used for CD50S.
I used it on my CD50S.
It is for DAX, but I bought it because I like the shape of Up type.
Installation is not attached as it is.
I bought an L-shaped bracket from Home center and modified it to fit.
The volume and sound quality of the Exhaust System is the same as OEM Product.
I don't think there is a Large difference in driving performance either.
If you like the shape, you can buy it for less than 10,000 yen.
View detail
Fits: HONDA MONKEY
Cospa strongest
There is no other exhaust system that is this cosmetic.
MONKEY Exhaust System Up Type is the best fit for me.
There are other Exhaust System Up Types, but they don't have Heat Guard or are quite expensive.
The price is phenomenal with the Heat Guard and the quietness is a high point.
There was no screw pitch misalignment, which is common with external exhaust systems.
Large land system is getting LevelUp!
I'm going to try to make the Exhaust System about 30,000 that Plating is ruining.
View detail
Fits: HONDA MONKEY, HONDA GORILLA
Cool
It's a powerful sound
However, the sound is considerably larger than OEM
I'm not sure about the performance, but I feel like I'm getting better out of it
I'm very happy with the way it looks
View detail
I put it on the SUPER CUB
It's for DAX, but I put it on my SUPER CUB
I bought this one, which is listed for 88cc - 124cc as I was planning to bore up, but In the end, I installed it with 50cc
Maybe it's because the Engine Displacement Volume was NORMAL But the volume was good as well as Smallish
It has a moderate feel to it, and it can be run on 50cc for the time being
Conversely, I think it's a bit underpowered in a vehicle that's being played around with 110cc or something crunchy
Also, the texture was beautiful for the price
Plating on Steel, so it may be tougher for those types that are left outdoors
In my case, I hung it on a Motorcycle Cover for about three months and left it in an uncovered parking lot But it didn't rust
I installed it on a SUPER CUB, not a DAX
The bracket on the back side was quite overwhelming as I managed with some things
I think it needs a little bit of work to put it on properly
As for Leg shield, it was a miraculous Clearance to avoid it
Also, the exhaust system will grow in the Right Side calf area, and But thanks to the Heat Guard, it's not hot at all
I rather enjoy LeftCorner because it allows me to do calf grips
I'm trying to find out if it's possible to attach it to MAGNA50 and other frames with UnderTube It is
View detail
Fits: HONDA MONKEY
I guess you could say it's an STD Exhaust System for Bore up
Takegawa17RStageDBoreDBore Up Kit88cc with quietness I was looking for an Exhaust System and found this product
It didn't look nearly as good as the OEM and didn't seem to be of much lower quality
Only the exhaust port is thicker, and it is judged to be an Other Brand Product that is slanted Point you can do
Included Parts:Gasket, Mounting Bolt, Nut all included and no additional parts are required
Installation was easy and easy with no distortion
When you start the engine, you'll see that it's a 250cc single cylinder OEM exhaust system and I felt that I could drive on public roads without any problems
I tried to run, but do not feel particularly badly out of the way, the noise does not become loud, and you can't worry about it I was able to run for fun without having to
Only the combination of Takegawa intake manifold and PC20 will turn the ThrowScrew The point of concern is that things are difficult
You can find a suitable tool, process the tool, or replace it with a screw that can be turned by hand, etc It's not a Large problem, because it can be solved
Cost performance is also high
View detail
Fits: HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY
Cospa is good
It was installed as a replacement for a Honda SOLO OEM exhaust system
50cc, carburetor is my impression of the OEM condition
We chose it for the following reasons
1) There are almost no exhaust systems for SOLO, but will MONKEY be available? I didn't know if it would work
I can't afford an expensive trial 。 At this price, even if it doesn't work, you can laugh it off
2) I thought it would be a good fit with the design of the motorcycle
(1)Side Stand interferes when raised, but can be driven
As long as you don't bank on it too much, I don't think it's a problem
2.Silencer's Bracket is not long enough at all
You need to cut a sheet of aluminum or other material to extend it
I think you can use the Bolt on the Seat rail to stop the Seat
3.Baffle is also included, so it's not too noisy, but still has a nice bass sound I am
I'm not sure about the power
It doesn't change much, especially at low rpm
At high rpm, Main jet at 65→70 is just right, and re-binding is 70km It's about
5. it's a beautiful piece of work and I think it's very cost effective considering the price
View detail
Fits: HONDA MONKEY, HONDA GORILLA (12V) Z50J-2000001-, HONDA GORILLA (12V) AB27-1000001-, HONDA MONKEY(12V) Z50J-2000001-, HONDA MONKEY(12V) AB27-1000001-, HONDA GORILLA2.6PS(6V), HONDA GORILLA3.1PS(6V), HONDA MONKEY2.6PS(6V), HONDA MONKEY3.1PS(6V)
Recommendation.
This texture, Recommendation at this price.
I am using it for NORMAL's MONKEY, but I am satisfied with both appearance and performance.
The sound is thicker and lower compared to NORMAL, and the volume is a feeling that it became slightly Large.
It is not a quiet, annoying Large room.
I think that it is Recommendation for those who think that they want Exhaust System outside the company with Normal look.
Cover, others seem to have some processing required, but I got to process without processing.
View detail
Fits: HONDA MONKEY, HONDA GORILLA (12V) Z50J-2000001-, HONDA GORILLA (12V) AB27-1000001-, HONDA MONKEY(12V) Z50J-2000001-, HONDA MONKEY(12V) AB27-1000001-, HONDA GORILLA2.6PS(6V), HONDA GORILLA3.1PS(6V), HONDA MONKEY2.6PS(6V), HONDA MONKEY3.1PS(6V)
Now, during installation
There are Z50J 1000001 to 1195595 in the selling agency's novel, but it was not possible to install it on my car body of 1162 **** without machining 4 LMONKEY, the attachment part of Rear suspension is thick and it interferes there
Bracket attached to the car body was forcibly bent by force, it was barely possible to install
OEMHeat Guard, 4 L is It is mountable to the bolt. I mean, there is nothing wrong It can not attach by interfering with the exhaust manifold part unexpectedly 4L Heat Guard inquired to the selling agency that it may not be able to be attached unless bent or processed If it is not possible to return goods It is useless because it is cheap also in polite correspondence It was full feeling Those who are studying Heat Guard 4 LMONKEY with 4 LMONKEY are cautioned
View detail
It looks good, it is super cheap.
I looked for HONDACHALY 50 's Custom purpose 30 years ago, because it was affordable, I purchased without hesitation.
OEMExhaust Easy System (About 10 minutes) Although it got off, attaching the fixing Band (3 or 4 times over) I had a hard time. (About 30 minutes)
However, I really got hit by Brake pedal and I gave it up.
After that, Stopper rubber for STAND (OEMExhaust system included) There is no,
Chain is in contact and rubbing, but it does not seem to be a problem as it is.
View detail
Fits: HONDA MONKEY, HONDA GORILLA
It is regrettable that Silencer has rust
There is rust but there is no problem on the performance No price is cheap so I'm wondering if this is something like this?
I was able to install without any problem for mounting ??
Where you get concerned about getting off and Torque is scrapped ??
View detail
Fits: HONDA MONKEY
Cospa best
Over Exhaust System was attached, but when commuting early in the morning in a residential area it is quite disappointing for explosive sounds (It's a nice sound, though) I go on the same road everyday at the same time.
There is no complain if this texture is around 6000 yen.
The sound is quiet enough to be surprised.
I am glad I bought it.
View detail