Reviews
Fits: HONDA CBX400F, HONDA CB400SF, HONDA CBR400F, HONDA CB400FOUR, HONDA CBX400F, HONDA CB400SF, HONDA CBR400F, HONDA CB400FOUR
Exhaust manifold Gasket
I chose the cheapest one and it was perfect - no problems and no gas leakage. View detail
Fits: HONDA CBX400F, HONDA CB400SF, HONDA CBR400F, HONDA CB400FOUR, HONDA CBX400F, HONDA CB400SF, HONDA CBR400F, HONDA CB400FOUR
Made by POSH for safety!
I always used KITACO but this was cheaper so I bought it.
Compared to KITACO, it is the same as KITACO Large and seems to work fine.
View detail
Fits: HONDA CBR1000RR, HONDA CB1000 SUPER FOUR (Big One), HONDA CB1300 Super Four, HONDA CB1000 SUPER FOUR (Big One), HONDA CB1300 Super Four
When replacing the Exhaust System of CB1100etc!
[How is it used?
When we replaced the Exhaust System, we had to replace the Gasket as well, otherwise it would leak and cause power down.
How was your experience with it?
It is designed for CB1300, but can be installed on CB1100 without any problem.
Of course, the quality is fine and can be used without disposal leaks.
How did it compare to other products?
The cost performance is good because it is cheaper and of higher quality than OEM Product and KITACO's same etc. products.
[Points to note]
Note that if it has not been replaced for a long period of time, it will stick to the Engine side and scratch it if not carefully removed.
To prevent waste leakage, replace the exhaust system with a new one even if it is troublesome.
View detail
Fits: KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZX-12R, KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZX-12R
Posh Exhaust Gasket
I used it on my GPZ900R.
The price was low and it worked fine.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Beautiful nuts
I bought these nuts on the Honda SuperCub and Monkey - they fit both motorcycles. They are not expensive, but they protect the screw from harmful influences from below. The quality is good. I bought these nuts for a Honda SuperCub and Monkey - they fit both motorcycles. They are not expensive, but they protect the screw from harmful influences from below. The quality is good. View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
no problem
CB223S is not in the list of compatible models but can be used.
I chose it for dress-up as well, since the original Nut had left on its journey after forgetting to fasten the main fastener.
I think it is overpriced for something that is hard to see.
View detail
Used for Exhaust System production
Used to make an exhaust system for a YamahaXV750E.
I used to use the ones NeoFACTORY handles, but when I bought the CFPosh ones to try out, I felt the quality of the bending process was better, so I decided to use CFPosh ones again this time.
As the description says, this Pipe has a high roundness rate regardless of the angle.
The Pipe itself is just a steel pipe, but the quality was good.
Also, although it was a cheap semi-automatic welder, it was able to weld without any problems.
I would like to have the opportunity to create another one next time and to purchase a Bend pipe with the Pipe diameter & bend angle I want.
View detail
For Exhaust System production!
It was used for the production of the original Exhaust System.
It is a 750cc 2-cylinder, but it is not such a sporty Engine, so we decided to make it with 38mm just below the Flange.
In the case of VTWINEngine like I am doing, I could easily make a front bank by buying a Pipe with a 180 degree bend and a 60 degree bend, and cutting and stretching it well.
The one I purchased this time is for Rear bank.
Rear banks have to be twisted into tight spaces, so they end up having to be chopped up.
The Pipe itself is frankly just a 1.6mm-thick steel pipe, but it is bent almost as a new circle.
Last time I bought BentPipe, which is handled by NeoFACTORY, I felt that CFPosh was better in terms of new circularity at the beginning of bending.
By the way, the product image looks about 100 degrees, but please be assured that what you will receive is a proper 90-degrees bend.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Long Exhaust Nut
I purchased silencer attachment pins to the cylinder on my Honda monkey for corrosion protection. In terms of quality, everything is fine, they are well loaded, the appearance is gorgeous. I recommend to purchase ... View detail
Used for techserfu's Silencer
Used for techserfu's Silencer which is mounted on GOOSE.
The dimensions are almost perfect. Purchased a second one after it fell off & was lost on the street the other day.
One thing to note is that there was only one hole on the Silencer side for fixing the baffle, so when the baffle was fixed in one place, the fixing hole was shaved off and the baffle disappeared due to vibration.
Two screws are cut on the BaffleBody side for fixing, so be sure to fix it in two places.
View detail
The fine Size is selectable, which is appreciated.
I purchased this one because the Screw pile on my current Baffle had been crushed.
The construction is solid with aluminum cut-outs.
I measured the size and purchased it, but the baffle was a little too large, so I had to shave it down and install it.
No complaints about the sound deadening effect.
View detail
For vehicle inspection.
It is good because it is inexpensive, and I think it is easy to process because it is made of aluminum. View detail
Wrapping around exhaust pipe
There was a concern about heat when converting to Atech-SPL, so it was installed in the OEM exhaust pipe.
Result 3. Quantity:I used it for 5pcs. It was easy to roll with good color and little fluff.
It is fully baked but still has a sweet aroma.
View detail
For Heat Protection and Fashion
I don't want to touch the exhaust pipe that just ran and get sizzling.
I thought of various reasons why it would be dangerous for children to touch it.
I love the Parenthesis with the cloth wrapped around the Motorcycle!" was wound up with the real story!
While it gives a sense of custom at once, it also gives a sense of raggedness.
I think it looks unbearably tacky to some people.
I think it's cool! I think it's cool, so I'll pass.
When rolled up, the insulation performance is good, and it appears to provide a slight sound insulation.
I'm personally pleased with Large!
Yes, I also diverted this one to repacking sound deadening material inside the Exhaust System.
Ordinary Glass Wool would fly away, so I thought this would be a good choice.
The result was a Large success.
View detail
Performance as a Baffle
Looks and finishes are good.
I've gone to the trouble of installing it.
There was almost no change in volume as Baffle.
View detail
DF200 DJEBEL Used at Rough & Road RSVSilencer
I purchased a used RSVSilencer and installed it because it was too annoying.
BoltQuantity for installation:They said 2 pcs, but we decided to TRY with 1 pc.
The rear end of the Silencer is gradually enlarged from 3, 4.5, to 6.5mm to allow the attached M6 bolt to penetrate.
"Okay" and put it against the Silencer exit... I can't get in!"
Caliper's actual measurement was 47mm, so I bought 47mm, but 46mm seemed to be the right choice.
I inserted it by tapping it as hard as I could with the wooden handle of the plastic handles.
After the installation, the exhaust sound was very loud. Slightly more energetic NORMAL?" Ranked first.
When Idling "Chica Chica." and the Tappet sound is so good that it sounds like a HUDDRILL. This is good.
I immediately performed a test run and did not feel any extreme power down, even when I turned it as hard as I could.
Also, totally unexpectedly, the low-speed Torque was enriched.
I am satisfied with the Large change because it is quieter and easier to ride.
I found this in someone else's Review, but the Hexagonal Wrench was not attached.
View detail
Fits: HONDA ZOOMER(Ruckus), HONDA ZOOMER(Ruckus), HONDA TODAY, HONDA TODAY, HONDA SMART DIO, HONDA SMART DIO
When replacing the Exhaust System
[How is it used? Used for ZOOMER
Was the one you received as per Image? Yes
How was your experience with it? no problem
[Points to note] There is none
How did it compare to other products? I think it's a good product.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Fits: KAWASAKI EX-4, KAWASAKI W400, KAWASAKI W650, KAWASAKI W800, KAWASAKI EX-4, KAWASAKI W400, KAWASAKI W650, KAWASAKI W800
no problem
I used it on a W650 assembly pipe and it installed without any problems. View detail
Aluminum is dirtier and less rusty
Material:I chose this one because it is aluminum and seems to be rustproof.
It is not cheap, and the precision is perfect.
View detail
good quality
Solid Spring for strength and durability.
It is Stainless SteelMaterial, so it will not rust.
If you take care of it, it will stay beautiful forever.
Ideal for replacing Full Exhaust System's Exhaust Spring.
View detail