Reviews
Ideal for lightweight
Installed on 8BK-RG74J.
No loss of horsepower with regulated engines = can be converted by replacing the Exhaust System. but there was not much change at the JMCA, where the regulations are tighter.
In the 250cc class, the Large body only varies by 1 to 2 horsepower no matter which Exhaust System is selected, so this Exhaust System is recommended for weight reduction purposes.
As for the sound, the 8BK is almost 90db OEM, so you hardly notice any change in volume, but some parts have a thicker sound depending on the RPM.
In terms of sound quality, I think you would feel more change with Planus or WR's Slip-on Silencer.
The quality, however, the accuracy of the front pipe was quite poor, and it did not fit neither the Engine nor the Center pipe, so it had to be installed while bending it with Lever.
Although less expensive than other Full Exhaust Systems, it would have been nice to have a more accurate product.
When installing the Silencer, it is recommended to temporarily fix the Exhaust Band and Bracket and then install the Bracket on the body of the vehicle, as it is quite difficult to install the Exhaust Band if you follow the Instruction Manual.
Also, although not mentioned in the Instruction Manual, it was necessary to change the Wiring position of the O2 Sensor.
The OEM position is fixed in front of the Clutch cover, but once removed and placed through the rear.
Although it has a few drawbacks, it does not look like other people's and can be lightened to a large width, so I think it is recommended for people who are visually oriented.
View detail
It looks good
The Exhaust Guard is fixed to the Exhaust Band, so it was difficult to align the Exhaust Guard and had to be removed and reattached 6 to 7 times. (It's a hassle.) Coordination.
There was not enough heat seat to cover the entire surface, so I applied the heat seat on the main side of the pipe, which is hotter.
It was installed without modification, but there is interference with the catalytic converter, so if you are concerned about this, you will need to shave it down or do other work.
View detail
Fits: YAMAHA WR155R
WR155R Full Exhaust System Comparison
I have tried three Full Exhaust System, PROLinerXR-1⇒DAYTONA(IndonesiaYamahaOption)⇒Yoshimura cyclone. As for the comparison of the three systems, my personal opinion is that overall they are 1st DAYTONA (IndonesiaYamahaOption), 2nd Yoshimura cyclone and 3rd XR-1. They all have their pros and cons...
XR-1 is really noisy enough to break your ears in Tunnel, and when VVA starts to work, it stalls (Gas is too thin), so it is obvious that Injection controller and fuel condition are necessary. YOSHIMURA's total balance is excellent and he is able to drive on public roads with confidence, and he is able to secure satisfactory torque and power from top to bottom. Lastly, DAYTONA is my favorite with YOSHIMURA's fee ring with higher volume. Also, it is the only one with a baffle, which allows for simple sound deadening, and the exhaust pipe is the longest of the three, which seems to secure the Torque. The difficulty level of installation is the same for all 3 Rings. However, only YOSHIMURA's Fender Eliminator has a blinker that interferes with the pipe, so it needs to be relocated. In addition, the Gasket of the middle pipe is required.
View detail
Exhaust System first replacement
I ordered this for my CA45A LETS4 because I had a cracked Pipe at the root. Tighten the Bolt and tighten the back Quantity:The 2pc holes were Bolt in while pushing and pressing the Exhaust SystemBody to align the holes.
The noise of the Exhaust System is quieter than before the previous OEM Exhaust System was broken, so it can be used on public roads and residential areas without any problems.
View detail
Short Tube Installation
Previously used Exhaust System with aluminum silencer.
The Torque is thinner overall due to the short tube, and I have the feeling that the engine rotation is lighter instead.
View detail
Exhaust pressure adjustment
cbr250rr mc51 AKRAPOVICExhaust System
cbr250r mc41 WR'sExhaust System
mounted on
AKRAPOVIC can also ensure exhaust pressure, and the volume is lowered just right.
WR's are too subtle with too much exhaust pressure. Volume goes down.
Glass Wool burns quickly, so it is a recommendation to wrap Stain Wool on top of the purchased condition.
Since the exclusive for RepairGlass Wool is expensive at 1,000 yen, commercially available for RepairGlass Wool with Stainless needle Gold is sufficient.
By the way, if you open your fingernail so much that it is too hard to insert it, if you open the Axel all the way, you can….
View detail
Fits: YAMAHA SR400, YAMAHA SR500, YAMAHA SR500, YAMAHA SR400
Sounds great but loud decel popping
I think this exhaust looks and sounds great, but there is loud popping when shifting gears and decelerating. Any advice on how to fix this? View detail
Installation is easy.
The OEM exhaust system is easy to replace if you are familiar with it, and when the baffle is removed, the bass is so low that it is hard to believe it is 125cc, but it is a blast.
It is a confirmed Level of neighborhood annoyance, but with Baffle, it was not much different from OEM.
Without Baffle, the low RPM Torque seems to drop.
It can also be considerably lighter.
View detail
It looks like they are all made of Titanium Alloy Gold.
The HeatProtector side has a long hole for good alignment.
It is unfortunate that Band's Screw was Minus-headed.
Material can be SUS, and a hexagonal head or Plus head is recommended.
View detail
For Scooter commuters to enjoy
The lower part of the muffler is lost from the Normal muffler, but I felt a stretch in the middle to the middle that is not present in the Normal muffler.
By replacing the Weight Roller, we were able to ride comfortably in city use.
The maximum speed is also quite good (laughs).
View detail
Fits: HONDA GROM
enchanting (Lol)
It was the first time I tried to replace the Exhaust System by myself, but I managed to complete it.
The Style has tightened up a lot!
I just couldn't get ECUReset to work. ( Nope.) Siksik…⇒ I'll have it looked at at my next inspection.
The sound in general was LARGER than I had imagined.
We live in a residential area, so we have to be careful about the sound of iDrink (especially in winter).
Sound is satisfied.
View detail
Appeal to appearance and surroundings (As a safety measure)
The sound will be a nice Appeal (laughs).
I used MORIWAKI muffler on my previous LEAD125 and I like the sound, look and feel.
If you expect it to run well, you can replace the Weight Roller at the same time for a good driving experience!
View detail
Mounted on CROSSCUB110 JA60
My favorite is the color Black and the heavy bass sound.
Power is also up!
View detail
GOOD GOOD Glass Wool Acoustafil
Cutting is accurate and no cutetc. is required.
The Glass fibers are braided and compressed thinly, so there is virtually no scuffing of the Glass fibers.
(but protective equipment is still required)
The compressed Seat is temporarily fixed with Tape and expands with heat after assembly.
The work of putting it in the tube is easy.
The purchase cost is usually a problem instead of the difficulty of the work being reduced compared to Glass Wool.
Silencer parts removal & disassembly, Rivet removal by Drill,
Rivet re-fixing, hole alignment, and removal of remaining gasketetc. using special tools,
Parts matching checks and other su-kills are necessary.
One 1100mm-long Seat is equivalent to one Silencer.
Two Silencers would require two pairs.
View detail
Easy to install!
Installation was easy.
Japanese Vehicle Inspection Correspondence, but I think the sound is too loud.
But it's cool, so I'm satisfied.
View detail
Fits: HONDA XL250S L250S, HONDA NY50 All models, HONDA CROSSCUB110 JA10, HONDA All models of GIORNO CREA AF54, HONDA SUPER CUB 110 JA10, HONDA SUPER CUB 110 PRO JA10, HONDA SUPER CUB series Engine cars (50-100cc), HONDA SUPER CUB series Engine car FI, HONDA Spacy50 All models, HONDA DREAM50 AC15, HONDA Spacy80 All models, HONDA VARIE All models, HONDA MONKEY series Engine cars (50-100cc), HONDA MONKEY series Engine car FI
Very common EXGaskett
CROSSCUB110 (JA45) Used to replace the Exhaust System of
I think Gasket is the same for all Manufacturers.
No exhaust leak etc.
It was cheaper than OEM Parts.
View detail
Fits: KAWASAKI ZXR250, KAWASAKI KLX125, KAWASAKI D Tracker 125, KAWASAKI BALIUS2, KAWASAKI BALIUS, KAWASAKI ELIMINATOR 250V, KAWASAKI ZXR250R
KLX125
KLX125
DrumstickDrumstick fits!
View detail
Fits: KAWASAKI VERSYS 650, KAWASAKI VULCAN400S, KAWASAKI VULCAN400S, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI NINJA1000 (Z1000SX), KAWASAKI ZXR750R, KAWASAKI ZXR750, KAWASAKI ZX-9R, KAWASAKI ZX-7RR, KAWASAKI ZX-10R, KAWASAKI ZRX400II, KAWASAKI ZRX400, KAWASAKI Z1000 (water-cooled), KAWASAKI Ninja 650, KAWASAKI ER-6n
grunting or groaning sound
I was convinced that I could be sure of the products here. View detail
Fits: HONDA glom
You can experience the effect!
The details are carefully crafted.
The replacement process was relatively easy and quick.
The Torque feeling at startup will be a little thinner.
The Engine turns pleasantly after running and is solid and powerful.
However, although the sound quality is good, it might be better if the volume were a little louder in the smallest volume so that the driver would not have to worry about it when driving around town.
Also, there was a Gasket LINK on the page where I purchased the product, so I bought it together, but it was for Full Exhaust System.
I wish it had been mentioned on the product page that a joint gasket is required for the Slip-on Silencer.
View detail
Fits: KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
light
[How is it used?
After installation, the car traveled about 200 km.
Was the installation difficult?
It is not so difficult to install except for the Flange, which is a type of two-piece flange, so it is difficult to install unless you get under the motorcycle.
How was your experience with it?
The OEM one is quieter, both idling and running, but the OEM one is louder. Personally, I was satisfied with the quietness, as it was just right for me. The sound quality is not as harsh as the OEM, but low and smooth.
Lightness is somewhat felt when pushing and pulling.
[Was there anything that disappointed you?
There are too many springs to install, but since spring hooks (devices) are not included, it is better to prepare them.
[Others]
Point or hang for installation...nothing special. If you dare to say so, there is no need to twist the O2 Sensor when installing it. If you install the O2 Sensor lightly before fixing the middle Pipe and turn the Pipe side around, you don't have to worry about the O2 Sensor wiring twist.
Availability and clarity of Instruction Manual - I can understand without it.
Items to buy together...Gasket is a good thing to have. The only other thing I need is heat resistant grease.
【Review】
Personally, I don't like the length of the exhaust end, the degree of raising, and the color (I prefer shorter, lower, and Polished Titaniumium), but I am very satisfied with the lightness, the Hand Bent-like curve of the exhaust pipe, and the high quality sound.
View detail