Reviews
For replacement of inside diameter!
I changed from a 16-pie to a 21-pie! The sound is better and it runs smoother. View detail
Fits: HONDA DAX, HONDA GORILLA, HONDA MONKEY
It's working just fine
I can use it normally as Exhaust Gasket. No problem at all. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
Good quality and sound from minimoto.
I have two of these pipes. I use them on 1969 k1 rigid framed with 108cc stroker kits. They sound good without the baffle and not too loud. Bike runs great with them. The finish and fit is very high quality. Polished nicely. Beautiful welds. View detail
Necessary and sufficient performance
The engine side mounting screws are difficult to remove without removing the UnderBracket and other parts. Other than that, the Large is strong enough for anyone. The performance of Large and Single4Stroke engines' exhaust systems are all similar. Silencer and exhaust pipe made of steel are impossible. There, the high price by name makes me doubt the thinking of those who buy them. As I mentioned earlier, two horsepower and three horsepower are no different. It is definitely better than rusting. As for the volume, it is not noisy at Idling and is at a level that is not a problem. It is not so loud at high rpm, but I don't think it is noisy. 100km is enough with the meter reading of ct125. Fuel consumption is not much different from NORMAL. If the one you put on is worse than NORMAL, please re-educate the Right hand. View detail
The quality of workmanship is made by Minimoto.
Mounting orientation (Quantity:Pair (for Left and Right) I purchased the wrong Bracket (I bought it by mistake and only temporarily installed it), and my impression is that the quality and workmanship is better than other manufacturers' Brackets, especially the welded parts are beautifully finished.
The offset value did not match my Exhaust System&iron CUB, so I had to buy another company's bracket.
The M8 screws cut into the mounting holes on the exhaust system side are also unique to other companies' products, and the stainless steel's high quality and SMART appearance make it number one.
View detail
Fits: HONDA MONKEY
OEM Type Exhaust System
I am satisfied with Large at this price!
The texture is just fine.
View detail
Fits: HONDA MONKEY
MINIMOTO MONKEY TYPE C STD Exhaust System Φ28mm Chromium Plating
Acquired for Honda Monkey. It's been a long time since I've thought about replacing the muffler. MINIMOTO liked the exterior (a huge plus in similarity to the original muffler). There are minor questions about lacquer treatment, but overall everything is very kind. I was delighted with the completeness, the whole range of necessary metizas and gaskets. The installation went perfectly (I think even the schoolboy will manage). And to the question of sound - it is beautiful, light and soft bass. I'm happy with the result, sorry I couldn't find a similar offer for the second moped (Honda Little Cub)... View detail
daytonma Exhaust Bracket For Right
About quality and texture I think the quality is really good About the feeling of use Incorrect length measurement but fitted to exhaust clamp bolts. Products to buy together An exhaust clamp with m10 bolts is required Difficulty of installation easy, simple Cost performance and comparison with other products I think the product is the best for the company that makes the exhaust, but I think it is a well-made product in various ways About shipping and packaging It took a week and the packaging is excellent Any concerns, cautions, or advice when purchasing We need to measure the length properly and choose I needed 150mm, but I chose 175mm, but 125mm was the correct answer View detail
Fits: HONDA MONKEY, HONDA GORILLA (12V) Z50J-2000001-, HONDA GORILLA (12V) AB27-1000001-, HONDA MONKEY(12V) Z50J-2000001-, HONDA MONKEY(12V) AB27-1000001-, HONDA GORILLA2.6PS(6V), HONDA GORILLA3.1PS(6V), HONDA MONKEY2.6PS(6V), HONDA MONKEY3.1PS(6V)
Sound is Large
Personally, I was expecting the sound to be a bit louder than the NORMAL, but there was not much change. If you live in a residential area, it may be just right.
Also, please note that the NORMAL exhaust guard will attach to the silencer part, but not the other parts (there is no bolt on the exhaust system side to attach it). I like the Forme without the Exhaust Guard, so I have no problem with it.
View detail
Great price for a high quality unit
One of the cheapest exhausts for the ct125 with a great quality finish and welds, I'm decently surprised. Pretty quiet too, for louder enthusiasts, you can remove the end baffle which will definitely make it a bit more loud. 9/10 View detail
It has a higher percentage of glass fibers than Titanium, and the manufacturer knows it, but they sell it as TitaniumVantage. Vinyl gloves are included with the product. View detail
tingle free
It can be rolled without wetting.
It does not tingle at all.
However, it might be better to wash the Motorcycle after rolling it up because it gets fluffed up.
Included are Rubber Gloves and AluminumTie Wrap.
The included AluminumTie Wrap is not tight enough, so you should purchase the Home centerAluminumHose Band in advance.
View detail
To hide burn marks
I was covering my SR400 with a blanket before putting on the cover, but the other day I accidentally made a scorch mark on the exhaust pipe area…
I bought and installed this Vantage to hide the scorch marks.
The Instruction Manual says that you don't need to put it in water to use it, and I think it's true, the Material was soft and didn't feel sticky.
This is the first time I've seen this kind of product in action. I'm very satisfied.
Included in the package are
ThermoVantage and Instruction Manual
Material:Stainless SteelBand*6pcs
1 pair of thin rubber gloves
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA
Original type exhaust for monkey - cheap and good
This exhaust was under my honda monkey z50k3 minitrail. Cheap exhaust that fits perfectly. Can't say much about it, does what it has to do for a good price. View detail
For heat protection of oil cooler
I purchased this product to install an oil cooler, hoping it would prevent heat damage.
I wrapped it around the exhaust pipe of MORIWAKIMX, but we have two FSprocket up and the start was a little weak. It became a little smoother.
I will install the Meter at a later date to see how effective it is against oil temperature.
View detail
Vantage
It's good in terms of feel, the exhaust pipe area was burned and dull in color, so it did a good job of hiding that. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA
I'm all about quiet, and this is the only way.
I use it on my DAYTONA 88cc.
By sacrificing performance, it achieves a volume that is slightly Larger than OEM. This is a product that will not bother your neighbors.
The Exhaust System is made at the lowest level and can not be installed with the included collar.
View detail
Fits: HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY
All lies.
Anyway, the welds are so bad that even compatible models can't be pimped out, and it interferes with the rear suspension, and the angle of the inserts on the engine side don't match, so I'm just laughing. (Lol) If you buy this, you must have both Hand Bent on the Engine side and Hand Bent on the Silencer side. I can't get the Hand Bent so I'm using only one side of the Bolt on the Engine side and forcing the back of the Bolt to be spread outward, but I'm not sure if the back of the Bolt can handle the exhaust leaks and the impact of driving. I really wish I hadn't bought it. View detail
Prevent burns!
[How is it used?
In an effort to increase the number of OffLoaders, we are co-owning a CRF125F as a RenBarrel vehicle.
The other day, when I borrowed it at the Race, I was unlucky enough to burn myself with the exhaust pipe when I fell, so I rolled up the Vantage.
Was the one you received as per Image?
As per Image
Was the installation difficult?
I wet it in water and rolled it up with some Overlap.
All locations except the start and end points are fixed with Wiring.
How was your experience with it?
It was my first time wrapping it and it was easier than it worked and didn't sting as much.
[Included Parts:were they on?
It contains 5 Stainless Steel Bands.
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I like MINIMOTO's Large that even these parts are prepared reasonably.
View detail
Used for CD50S.
I used it on my CD50S.
It is for DAX, but I bought it because I like the shape of Up type.
Installation is not attached as it is.
I bought an L-shaped bracket from Home center and modified it to fit.
The volume and sound quality of the Exhaust System is the same as OEM Product.
I don't think there is a Large difference in driving performance either.
If you like the shape, you can buy it for less than 10,000 yen.
View detail