Reviews
Fits: HONDA Africa Twin Adventure Sports ES, HONDA Afriva Twin Adventure Sports, HONDA Africa Twin
AFT 1100 OEM Quick Shifter
Perfectlly working mainly from 2nd to above gears. 1st to 2nd still need some adjustment or skill improvement. Anyway very easy to install (detailed instructions) and configure. View detail
It's a hassle to search and ask for help! For those who want to
In the overhaul of SEROW225, I disassembled the upper waist, so I needed a whole set of Gasket.
I thought that OEM is the best in terms of quality, but if I accumulate a lot of intentions, it will cost a certain amount of gold, and there were some parts that I was not sure whether to change or not, so if I can replace all of them at this price, it is easy.
The quality of the product is absolutely fine. It is totally usable.
View detail
Fits: HONDA DAX125, HONDA MONKEY125
Is it essential in modern times?
Good product
When you live a life where your phone is indispensable, battery is always a concern.
The USB port gives me a sense of security.
If you read the Instruction Manual carefully, I think it is gentle as a work S-Kill.
However, it is necessary to pay attention to the removal and installation of the light cover (plating parts) and the fit of the wiring.
View detail
Ideal for lightweight
Installed on 8BK-RG74J.
No loss of horsepower with regulated engines = can be converted by replacing the Exhaust System. but there was not much change at the JMCA, where the regulations are tighter.
In the 250cc class, the Large body only varies by 1 to 2 horsepower no matter which Exhaust System is selected, so this Exhaust System is recommended for weight reduction purposes.
As for the sound, the 8BK is almost 90db OEM, so you hardly notice any change in volume, but some parts have a thicker sound depending on the RPM.
In terms of sound quality, I think you would feel more change with Planus or WR's Slip-on Silencer.
The quality, however, the accuracy of the front pipe was quite poor, and it did not fit neither the Engine nor the Center pipe, so it had to be installed while bending it with Lever.
Although less expensive than other Full Exhaust Systems, it would have been nice to have a more accurate product.
When installing the Silencer, it is recommended to temporarily fix the Exhaust Band and Bracket and then install the Bracket on the body of the vehicle, as it is quite difficult to install the Exhaust Band if you follow the Instruction Manual.
Also, although not mentioned in the Instruction Manual, it was necessary to change the Wiring position of the O2 Sensor.
The OEM position is fixed in front of the Clutch cover, but once removed and placed through the rear.
Although it has a few drawbacks, it does not look like other people's and can be lightened to a large width, so I think it is recommended for people who are visually oriented.
View detail
It looks good
The Exhaust Guard is fixed to the Exhaust Band, so it was difficult to align the Exhaust Guard and had to be removed and reattached 6 to 7 times. (It's a hassle.) Coordination.
There was not enough heat seat to cover the entire surface, so I applied the heat seat on the main side of the pipe, which is hotter.
It was installed without modification, but there is interference with the catalytic converter, so if you are concerned about this, you will need to shave it down or do other work.
View detail
Silver insert color is nice.
Installed in conjunction with Grip replacement.
Since the motorcycle has many plating parts on the body, silver was selected as an accent to the handlebar's black.
The color is good and the Silver looks good.
We considered heavier products, but chose this product with less thickness considering the width when parking.
View detail
Save money compared to buying at Rose!
The color stands out and gives it a custom feel, and as a manufacturer, I feel secure. I usually use OEM products, but I bought this product for fractional adjustment as well.
The quality and appearance were satisfactory.
View detail
Good quality, good price
Old rim lock disintegrated and needed a new one. This is almost identical to stock and fit exactly as it should.DRC rim lock is as good as any other rim lock. It weighed considerably less than what I was expecting.I always choice zeta, really quality parts and the best price Easy install but make sure you balance you wheels. View detail
Anyway, it was hard.
The CT125 Rear tire GP-5 has 2,0mm left, so I'll change it after a few more runs, but I'm running a GWCampaign, so I'll buy the Tire while I can, and I'm in the On 9, Dirt 1 ratio here, so not completely On road, I decided to go Adventure oriented.
So, after much deliberation with the well-reputed Anakee STREET, I decided to go with D604, which has no Reviews at all, as I am a minority, and write my first Review.
In a review by a certain Large River in South Brazil, the only negative image was that it was hard and vibrated.
After touching the one that arrived at my house for a bit, I was prepared that it would be hard and tiring, as it reminded me of the T63 thing from company M.
Now, when I got it in my hands with the usual Pattern, I already wanted to replace it, and I had planned to replace it next month, but I started to do so (laughs).
As you might expect, there is a direction of rotation for installation, so we carefully checked the direction of rotation before starting work.
This is my first time to replace Tire on CUB, but I will follow the theory here.
The GP-5 has a soft bead and was relatively easy to remove.
Now, let's start the assembly.
As usual, apply a generous amount of Bead wax.
Unlike off-road vehicles, we do not want to scratch the rim, so we use rim protector while working.
It's already hard even to fit the first time!
Fit the One Side and put in the Tube. These are not so fiddly.
Turn it over and put the other side in, but it is hard anyway!
After fitting half of the wheel, I held it down with my foot and lever it in, but the remaining 20cm or so was tough!
The installation was done carefully, boldly, and by brute force.
We managed to complete the work without any holes in the tube and with a clean rim.
I ran the car for a while, and it is true that the slight vibration from the Rear has increased, but it is not at a Level that bothers me that much.
Grip is often seen as such and such, but well, it is a CUB, so it can run and stop normally.
We don't ride in the rain, so as long as the dry grip is good, it's fine!
The groove is somewhat larger than GP-5, and the block is also larger, but the tread surface and SIDE are harder, so I think it is easy to be played on the dirt.
Muddy terrain is likely to Stack if not driven well, but the CUB does not have that kind of driving ability to begin with.
If you are used to working on CUBs with Spoke wheels, and if you are used to working on them, and if you drive in an adventurous manner, recommendation.
I thought that GP-5 would be easier to work with when Puncture was done, and that in the end the standard Tire would be the best. I thought that the standard Tire would be the best in the end.
View detail
GB Engine Guard
[How is it used?
24-hour (e.g. observation, operation (of a machine), care (of patient))
Was the one you received as per Image?
high
Was the installation difficult?
Easy
How was your experience with it?
No problem
[Included Parts:were they on?
OK
[Was there anything that disappointed you?
Oil replacement has become a bit more difficult.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: HONDA BENLY50, HONDA CB250R, HONDA CT110 HUNTER CUB, HONDA DAX, HONDA glom, HONDA XELVIS, HONDA Night Hawk, HONDA JADE, HONDA HORNET, HONDA GB250 CLUBMAN, HONDA DREAM, HONDA CL250, HONDA VT400S, HONDA R100 ROADSTER, HONDA GB400, HONDA CB400, HONDA CB400SF, HONDA BROS, YAMAHA RENAISSA, YAMAHA SR250
It's very cost effective.
It is OEMMirror-like enough to be satisfactory for the price.
Plating is clean, mirrors are not distorted, and there is no blurring while driving, so rearward vision is good.
The difference between OEM and Large is that the ROD is shorter (lower) and the black parts that look like shock absorbers are just materials.:It means that it is a Plastic Cover. Of course, there is no way to add a shock absorber at this price, so it makes sense.
Overall, I think this is a good product with high cost performance.
View detail
ease of use
Very easy to handle. View detail
Although there is a high degree of freedom
The flexibility is high, but the number of mechanisms is large, so it can be a bit of a challenge to install without thinking about it.
Texture was appropriate for the price, and visibility was not much different from OEM.
With a single cylinder, there is a certain amount of vibration.
The hardness of the moving parts can be adjusted by you, giving you peace of mind.
View detail
Windproof effect + does not destroy Style + makes cleaning easier
I have an OEMHigh Windscreen, but when I replaced the Helmet, the Wind Cutting noise became worse.
The wind was now coming from the upper half of the helmet, but if the Adjuster is raised to the Largeest setting, the wind is no longer coming from the helmet at all.
It is easy to install, and if the adjuster is lowered, it hardly disturbs the style.
It was also good to have space between the Screen and Bracket, making it easier to clean.
The disadvantage is that it is not possible to put something like a Screen Mounting Bar Holder between the Screen and Bracket due to the installation, and the price...
View detail
It was possible to install on VSTROM250SX.
It was possible to install on VSTROM250SX. View detail
Nice touch - but problems for yourself
Installation is a nightmare. You have to remove your whole tail assembly except you subframe. The new undertray comes with battery slot, but misses some of the grooves required to route wire harness. Putting back the tank had challenges. Fitment is ok. View detail
Great rigidity.
The pipe is thicker and has more fixed bolts than the OEM, so it is very rigid.:It comes with a Plastic Slider, so it will be cheaper in case of moss.
However, installation was a challenge. Since it is slightly gapped, I managed to install it by fine-tuning while loosening and temporarily fastening.
I thought it would take an hour to finish and started working on it at 15:00 and finished at 19:00. I think it was an individual difference.
The product is good and I am satisfied with the Large change.
View detail
DUNLOP Dunlop Rim Band [17in.
The one that was installed when the car was delivered was replaced for the first time.
If the Rim Band is damaged, it can lead to puncture, and since it is not expensive, it seems to me that it should be replaced every time the Tire is replaced.
View detail
It's fine without it, but it's not tight enough without it.
[How is it used?
Mounted on Archi's Seat
Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
Not difficult, but since the length is Limit, Bolt tightening while pulling a little.
How was your experience with it?
Without it, Seat's Balance looks bad.
[Included Parts:were they on?
Mounting Bolt only
[Was there anything that disappointed you?
Nothing in particular, but I wish it had been included instead of sold separately.
View detail
Even if it's not a low-headed Bolt….
I purchased this to improve the hardness of the entry of Shift on my 2014 NINJA1000, which had been bothering me since I bought the car used.
Installation could be done without removing the Cowl, so it took only 5 minutes.
However, when installed with the supplied low head bolt, it does not interfere with the OEM change lever, but there is only a gap of about 1mm, which bothered me, so I installed a M6×10 button cap bolt with a lower head than the low head bolt to secure the gap.
Shift entry remains a little stiffer than before, and I feel that the shift feel has become tighter.
I wish it were a little cheaper because it is expensive for such small parts.
View detail