Reviews
Bolt cover
It seems to be good for Screw head protection and One point dress-up.Quantity:1 Set of 3pcs., Plastic, slightly stiff.
Installation is fine, but when removing it, it almost cracks.
Lack if you force it off, the color will peel off.
The price is not that much, though, so I would just buy it again.
View detail
Hexagonal hole accuracy not good enough, soft?
Hmm.
It is delicate to say the least. The hole itself is shallow because it is a low-head bolt, but if you tighten it with the specified torque, the tool will bite into it and the hole will be star-shaped.
I don't want to think about when to remove it. LOL.
Stainless looks good, but what is the cosmetic value in terms of total? Total?
View detail
Different colors!
Functionally, there is no problem, but the color of the terminal is different between the picture shown on the website and the actual product received!
The photo shows Silver, and the received item is Gold!
I wanted to be inconspicuous and bought it because it was Silver….
View detail
The ape 50 was equipped as output port of an oil cooler. The goods themselves are made very finely and there was neither a bali nor a wound. I think that such a little thing will lead to a manufacturer's reliance. I think how it is that takes
The ape 50 was equipped as output port of an oil cooler.
The goods themselves are made very finely and there was neither a bali nor a wound.
I think that such a little thing will lead to a manufacturer's reliance.
I think how it is that takes no less than 500 yen to this product.
Although the tapped hole was cut and attached to the clutch cover, I got it to be safer to give a pro the direction where processing of drilling etc. is diffident.
I think that it will succeed if it is processed by itself, and it takes care about the following three points.
- Put the mark on the place which punctures to a punch correctly.
- Change the drill into the thick thing gradually.
Like [ of 1 mm -> 2 mm -> 4 mm -> 6.7 mm ].
- Use cutting oil, when using drilling and a tap, and carry out slowly.
I think that it will succeed if it takes care about these.
If it practices, I will think that it is better.
View detail
No better than OEM Parts
I went back to OEM Parts within a few weeks of installing it.
Compared to the SCM435 bolt from OEM Parts, the strength of the bolt is absolutely insufficient. When I installed it, the tool mark was unusually deep when I tightened it with the specified torque, and I immediately thought it was no good.
The OEM Bolts were not inexpensive either, but performance should be more important than design in the installation of a critical security component Bolt. On reflection, I went back to OEM Parts.
View detail
I'm not very good at finishing or anything.
Pulling a lathe by myself is a pain in the ass!
It's helpful to have these things on sale when I'm in a bit of a bind.
Sometimes I wish I had a few more thicker lineups, but I'm just thankful that they have this stuff available as a ready-made product.
Every time I use this kind of thing, I think to myself that I should thank the Manufacturer before I complain about anything.
View detail
Adaptable Outer Diameter
The product description says that the wire outer diameter is between 1.5 and 2.9mm
Threading Emon 1.25sq. wire (Standard:2.7mm, Largeest:2.8mm) is not possible
0.It looks like it's better to use it on wire of 75sq or less
It may be that the one I got happened to be shrinking due to long term storage, but the power line It's inconvenient that the notation Label doesn't fit over 1.25sq m
View detail
Firmly fixing it is difficult and impossible
Purchased the SetrabOil cooler to install on my MONKEYFrame But I think there are some to use it as a supplementary
Because it is impossible to fix Firmly only with these Parts, it is used only as an auxiliary It is possible to do so
View detail
Accuracy...
Since OEMCap Nut of Cylinder head came, I bought it for Replacement together with Reinforced Stud Bolt.
1 pc out of 4. The accuracy of the thread of the screw was bad, and the thread of Stud bolt was broken owing to gnawing. Is it inferior to Made in Thailand's OEM Parts and is not JAPAN?
View detail
usually
It is very ordinary. It is just a Manufacturer item. Used for CB 1300. OEM purchased at the DREAM store before was cheap. No trouble after installation. View detail
Used for Disk bolt of MAJESTY 125
Even though others have already been written. Hexagon seems to be licking even if I use Torque wrench and tighten with Torque prescribed.
It is true also with pure Normal Thread Screw, but this hex of Bolt is not a deep hole, so it may be easy to lick.
Considering things at the time of removal, too much attention is given to Screw lock.
If you are worried you might as well buy Steel from OEM Product.
It looks like GOOD because it is hard for Rust to look.
View detail
I wonder if I can fly by vibration
Cap of Handlebar Post of GSX - S1000 flew by vibration, so I bought this, but if inside diameter is a bit bigger Large, I can firmly insert it, but I feel a little loose.
I wish I could not fly again ....
View detail
It was used on the occasion of an oil change. Although the Gasket currently attached from the beginning till then was used about, it was dreadful to have licked the Screw of a Crankcase and it exchanged. Although this product was used a number
It was used on the occasion of an oil change.
Although the Gasket currently attached from the beginning till then was used about, it was dreadful to have licked the Screw of a Crankcase and it exchanged.
Although this product was used a number of times, now, the thing of Original Brando of a certain tool store is used.
The other side is cheaper although it is almost the same as the goods here.
View detail
[Webike Monitor] In exchanging the Throttle wire, it adopted. Although two insulation lock value processing was carried out usually [ ], it processed with this product this time. Appearance has also fixed the Wire to favorite direction with last
[Webike Monitor] In exchanging the
Throttle wire, it adopted.
Although two insulation lock value processing was carried out usually [
], it processed with this product this time.
Appearance has also fixed the Wire to favorite direction with last thing as a result of
.
He has no complaint, if the number of entering
is increased and the unit price per one is lowered.
View detail
A thing is thick, and although it is reliable, I want you to use about 100 yen. although used about 2 or 3 times -- a leak -- it spreads and can use that there is nothing.
A thing is thick, and although it is reliable, I want you to use about 100 yen.
although used about
2 or 3 times -- a leak -- it spreads and can use that there is nothing.
View detail
It is the same kind as fixing cowls, such as a moped, of screw. It becomes [ Is honest? ] and is high. It is better to have gone to the home center and to cut, if there is time although he bought it without the method.
It is the same kind as fixing cowls, such as a moped, of screw.
It becomes [ Is honest? ] and is high.
It is better to have gone to the home center and to cut, if there is time although he bought it without the method.
View detail
Although used for changing management of an oil cooler, it cannot obtain that color has only blue under the condition that size deployment is satisfactory. Although a brake hose is also so, if it is called the parts of alumite treatment, blue red of a
Although used for changing management of an oil cooler, it cannot obtain that color has only blue under the condition that size deployment is satisfactory.
Although a brake hose is also so, if it is called the parts of alumite treatment, blue red of a time-tested product is amusing.
View detail
The ape 50 was equipped as output port of an oil cooler. The goods themselves are made very finely and there was neither a bali nor a wound. I think that such a little thing will lead to a manufacturer's reliance. I think how it is that takes
The ape 50 was equipped as output port of an oil cooler.
The goods themselves are made very finely and there was neither a bali nor a wound.
I think that such a little thing will lead to a manufacturer's reliance.
I think how it is that takes no less than 800 yen to this product.
Although the tapped hole was cut and attached to the clutch cover, I got it to be safer to give a pro the direction where processing of drilling etc. is diffident.
I think that it will succeed if it is processed by itself, and it takes care about the following three points.
- Put the mark on the place which punctures to a punch correctly.
- Change the drill into the thick thing gradually.
Like [ of 1 mm -> 2 mm -> 4 mm -> 6.7 mm ].
- Use cutting oil, when using drilling and a tap, and carry out slowly.
I think that it will succeed if it takes care about these.
If it practices, I will think that it is better.
View detail