Reviews
failed to pass inspection
Less than one year after replacement, some of the bulbs went out and the Stop became non-lighting.
Although I thought it was faintly on the day before the inspection, it was not lit on the inspection line.
Even if we can discount it to individual differences, the quality control is so poor that we will refrain from using the same Manufacture's products in the future.
View detail
PCX125JK05
Front suspension of PCX125JK05 is Quantity:Pair (for Left and Right) The size or rather the shape is different in
So Quantity:Pair (for Left and Right) I don't remember which one, but it doesn't go on straight away, so a lot of ingenuity is required.
It was scratched or the paint peeled off.
Rubber sheets for protection, such as double-sided tape, should also be prepared.
I have no problem with the sturdiness of the product or anything like that.
It would be nice if there was a dedicated Bracket, but there is not.
I wonder if it will be attached if Type is made into 44 pie.
View detail
Durability concerns?
Used in CUB press 50.
It is very bright due to the fact that it is LED. When I first bought it, I thought it was a very good buy.
However, about two weeks after purchase, it finally stopped lighting up with symptoms like poor contact.
I'm wondering if the vibration caused the damage.
I purchased the LEDs with the expectation that they would last for a long time, but they stopped working in a shorter period of time than expected.
I can say that it would have been a good purchase if it had been used for a long time, but the period of use was too short to say it was good.
I think the price is not very cheap product, so I expect improvement in durability.
View detail
Chinese quality
[How is it used?
I installed Fog Lamp on FZS600 and introduced IndicatorSwitch with Fog Mark as a measure against vehicle inspection.
Was the one you received as per Image?
The quality is a bit disappointing. The Fog Mark was mounted on the Body with a slight tilt. I tried to fix it in the correct position by removing the rubber cover of the bellows, but it was fixed so tightly that I could not do it. I tried to remove the rubber cover from the bellows and fix it in the correct position, but it was not possible because it was firmly fixed in place.
Was the installation difficult?
I installed it on a DRC bar mount, but it does not match the bar diameter slightly and there is a gap on the mounting surface, but I managed to install it. I used Screw Loosening Fluid because the gap was not tight enough to fit the bar and the Screw was about to loosen.
How was your experience with it?
I was worried that the blue light of the Indicator might be bothersome to my eyes when it is turned on at night, but it did not bother me much while driving. During the touring, I drove in heavy rain several times, but the waterproof performance was fine.
[Included Parts:were they on?
Includes a complete set of parts needed to turn on the fog.
[Was there anything that disappointed you?
The functionality as a Switch is fine, but the quality is not so good.
Other items that would be helpful
(1) Point of attachment or hang:Depending on the mounting position and angle of the Switch, Blue light may be a concern when driving at night?
2) Availability and clarity of Instruction Manual:I think it is relatively easy to understand because it is illustrated.
(3) Note:Ensure that Wiring is handled without undue force and Connectors are connected.
4) Items to buy together:Screw loosening fluid.
(5) Opinions and requests to Manufacturer:Improve quality and assembly accuracy.
View detail
Excellent LED lamp to replace the original one
LEDColor:Yellow
I replaced my OEM headlight with a Multi-reflector headlight and am using a 6500K LED Bulb, but now that a Yellow Bulb is available, I wanted to see the difference.
Color:Yellow didn't feel as dark as I thought it would.
Note that Motorcycle after 2006 is a violation.
I think it would look great on an old car.
View detail
It is quite dark for a Headlight Bulb.
[How is it used?
Purchased to save power over NORMALHalogen bulb.
Was the one you received as per Image?
The Package was poorly packaged with simple packaging, but the product itself is fine.
Heat sink is solid and not as badly made as I expected.
Was the installation difficult?
Installation is easy, as the valve is simply replaced.
How was your experience with it?
The LEDs are only on one side, so they seem darker than the latest LED bulbs. It is not likely to pass the vehicle inspection, and it is not suitable for a large motorbike.
[Included Parts:were they on?
Nothing is attached.
[Was there anything that disappointed you?
The drawback is that it is dark for low power consumption.
Recommendation for more high Watt bright LED Bulb.
▼The H4Type is sold out, and I feel that this functionality has reached its limits; it is a Headlight Bulb, so it is useless without functionality, so I can't shake the feeling that it has been eliminated as a result of the evolution of more high Watt LED Bulbhe.
View detail
Dazzlingly bright.
I wanted to convert the VMAX Blinker to LED, but I was hesitant because the Blinker relay is a BlinkerControlComputer, so I could not replace the Relay, and the only solution was to put a resistor in the Harness.
I checked, and to my surprise, there was a pontoon Valve.
So, this product is 2Quantity:Buy the set
Measured the valve size and ordered a small one to be installed.
When I tried it on, the Rear could be worn with only a little bit of atamen interfering with the Lens.
The Front was a Double Bulb of the type that lights up in Small. (SmallWiring was killed and I didn't notice.) I'm a bit of a failure.
Skip one of the Bracket bins and install a Single Bulb.
It did light up, so that's good. There is a little interference with the Lens, but so far it is Large sturdy.
The brightness is much brighter than the Normal valve, close to dazzling.
Indicator went bad and became Hazardous, so we used a different product to counteract the problem.
See separate impre...
View detail
For the price
I installed it on a PCXJK05 FrontDamper, but it's not easy to install on the disc brake side.
The Motorcycle side was scratched because it was uneven and gapped as it was being attached.
Rubber sheet is attached to the bracket, but if it is not fixed to the bracket, the rubber gapes and this is difficult to do.
You should inspect it regularly.
View detail
Good
At first using this product, I thought the light was not very impressive, but no, this product has a high degree of perfection, light distribution in cos easy to see the road, wide field of vision, convenient light without glare, in general, the more I use it, the more I like it. next time i will use delta's higher end product ------------------------------------- --------------------- At first, using this product, I thought that the light was not very impressive, but this product did not have a high level of completion of the light allocation in cos easily visible the wide view of the light -eyed light, not the more dazzling, the more you like Next time I will use the more advanced product of Delta Powered by Google Translator View detail
Fine
Easy on the eyes. The specification states that 2 bulbs will give 3200/3600lumen brightness because one bulb only gives about 1800 lumens, this is very misleading I should have chosen your higher-end product ----- --------------------------------------------------- --- Thuan eyes are easy to see. Specifications specify 2 balls will give 3200/3600lumen brightness because one shadow only gives the brightness of about 1800 lumen, this is very easy to mislead I should choose your more advanced product. Powered by Google Translator View detail
It looks exquisitely fake.
I don't expect much from the price, but it is what it is. If it breaks, that's all there is to it. View detail
ZeroSeries Fog Lamp3000K Impressions
It is bright enough to safely ride a motorcycle on dark mountain roads. I will be happy if I can confirm the durability of this inexpensive product in the future. View detail
Excellent powerful LED lamp for scooter
Cheap
Inexpensive?If you want to convert your headlight to LED, this is a good choice. View detail
Power saving, good response speed
I purchased Repeat because I had installed it before but it was damaged in a rear-end collision. I think it is more reliable than the products made by unknown manufacturer. I have no complaints about the brightness. View detail
Price suitable
It's worth the price
It doesn't feel as bright as 6000k.
I still think it is better to buy a good Large hand
Sufficient for driving in the center of the city.
View detail
Cost performance good
It is H4Spec. so it is easy to remove the cover of the light and replace it, and the brightness is good enough so that even old motorcycle can use the newest light. I am using it for SEROW225W and FAZE. View detail
Brightness is sufficient
I have purchased and used two of them.
It is brighter than OEMLight, as if it might be brighter than Headlight.
If you want to convert to Number PlateMOTARD, this product is recommended.
Some Wiring Kits are available as related products, so you can tie them together with no worries.
View detail
Check for conformity with a knowledgeable person.
I had already replaced the OEMSmall blinker on my SR400 with a 15WType (OEM) Relay, so I thought I could install it with a bonnet, but it turned out to be a high flasher, so I ended up replacing it with a LED Relay at a motorcycle shop. The blinker of course lit up OK, but the SignalLamp of the Meter was so dark that I replaced it with a LED Lamp as well.
It turned out to be quite expensive with labor charges, etc. I wish I had consulted Motorcycle shop from the beginning.
The brightness is satisfactory for Large.
View detail