Reviews
You should have the store do the installation.
Wiring is tedious, it took me 6 hours. I had originally installed a Mistuba camera, so I thought I would use it if I could, but the terminals were different, so I had to remove the existing camera altogether.
About Camera
The Camera in the "Included Parts:" section is smaller than the Mistuba one. Moreover, it was not compatible with the Bracket on the License Plate, so I had to modify it to fit the Bracket.
About Cable
The power supply cable has a +- terminal that looks like a round terminal for direct connection to the buffer and no terminal for ACC. I think it is a hassle for motorcycles that do not have a terminal to take out ACC like CB.
About the attached Mount
The monitor is in the way, so I can't pull the key out, and I can't seem to swing it around, etc. I have made a 1 inch BallMount with a pontoon. I think it is better to wait for the official product because it is obviously a modification.
View detail
![Tire Pressure Sensor (Front/Rear) [for AIO-5Lite]](https://img.webike-cdn.net/catalogue/images/128410/SRS-002_01_TS.jpg)
Fits: Others AIO-5 Lite
Tire, Management
I think it is very good to know the air pressure and temperature of the tires. The only thing is that it is a little expensive, but it is very useful when I am on the road. View detail
![LCD Protective Glass Film [for AIO-5Lite]](https://img.webike-cdn.net/catalogue/images/128410/SRS-007_TS.jpg)
Body is expensive, so it is safer to put it up.
Since Body is quite expensive, I bought it just in case.
The large size is Exactly because it is a dedicated product.
There is no specific Instruction Manual.
There is no installation Guide or anything like that, so after locating the Large body, you just peel off the Seat and take a shot without thinking.
I was nervous, but it stuck well without any air bubbles.
I put on the protective Seat before installing the Body, so I do not know how the sensitivity of the LCD Touch panel on the Body has changed, but it responds properly.
Since the price is about the same as the LCD protection GlassFilm for the phone, it would be safer to put it on.
View detail
Expectations for the future.
Saturday, December 2, installation.
Installation can be done by an individual if he/she is able to take out the ACC power supply and handle the Wiring.
Just installed, so not sure how it will be used.
The image quality of the appleCarPlay connection and DriveRecorder looks good.
However, the initial setup (connection to the smartphone) was surprisingly difficult.
The Body is not likely to be easily removed (wiring and special tools required), so it is unlikely to be stolen.
However, leaving it on all the time is not good for your mental health….
Maybe blindfold them with a Towel or something.
Up-dating of Farm Wear is possible, so we are looking forward to the future.
View detail
Used to fix voltmeters
It is inexpensive compared to other products. It can be installed anywhere.
It is a good item
View detail
Is good
It is a solid Bracket with a high quality feel.
Double-sided tape is also included and the angle can be adjusted freely, making it easy to use.
View detail
Mistuba Sankowa EDR-21 for switch installation
I used Mistuba Sankowa DriveRecorder-EDR-21 for Switch.
The mirror is used in conjunction with the Mirror. The switch itself is installed with double-sided tape.
The process is quite simple.
Lamp lighting is easy to see and easy to use since there is a Drareco Switch by the Handlebar.
View detail
EDR-21G GPSAntennas
I used it to install GPS Antennas on my EDR-21G.
I used it to organize the various items I have installed around the Handlebar.
View detail
The design and large size fit in the car body.
I use it with XL1200C SPORTSTER 1200, and there is no sense of discomfort even if I install it in the body without being too large. Because I do not pull out and insert it every time when I am touring, it is OK though I feel that opening and closing is a little troublesome. By the way, the same product is attached to the other side of the car body, and I use it for a little Accessory Case. View detail
It is useful for Repair.
I bought this to replace my old ETCAntennas because the base was getting rusty and the double-sided tape was included and the angle was freely adjustable. View detail
In Accessory Case
Because the Rider's belly is sticking out so things don't fit in the Pocket (lol)
I bought it as a Porch because I wanted to keep it on my motorcycle all the time and use it right away I did
The capacity is only enough for ETC, but the USBCable, Stand holder, and Accelerator is now in
There is a flap, so things don't fall out without squeezing the zipper, and it's easy to operate with one hand
There were four holes in the back of the Thailand lock, but I ignored them (laughs), and 10 in the Center There is a hole of 2.5mm, so I bolted it in place
View detail
It's PVC, so it's safe to expose to the elements
The price and low price of the Case for ETC made the decision to buy it
While most of them are genuine leather, this one is inexpensive and made of PVC, so you don't have to worry about maintenance and getting wet in the rain It's very easy to use However, I am worried about its durability because it is soft and not firm like genuine PVC I think you'll have to check the deterioration of Tie Band while using it to install to the body of the car
It's a bit cumbersome because of the way to fasten the lid with a belt It would have been better if you could take it out a little easier, but the price is low enough
View detail
Motorcycling Companion without a Load
It's a necessity when attaching a separate ETC to a motorcycle without a load
There are screw holes, so if you extend the bracket from the body of the car, you won't have to worry about it coming off No, sir
I think you can put it on quite a few different places if you get creative
I think that it is easy to use Large because it becomes easy to insert and remove the card
In addition, only the attached Tie Wrap is fragile as others have written, and even if you just pull on it I'm loosening up
It's better to have a commercial product
View detail
Quality is excellent
Quality is an excellent item.
I could not install it between Sus and Blinker due to Small raw judgment mistake.
Placed behind Plate that I installed at the end of my troubles (Before) It was to.
Installation was easy, but I had a hard time handling Wiring.
I love it..
View detail
Mistuba MSC - BE 700 E can be stored
I used it when I temporarily removed the Side bag which housed ETC.
Although the MSC - BE 700 E was not listed in the correspondence list, it seemed to be tense numerically and it was perfect fitting in fact.
Although it was generally satisfactory, it became a deduction that the claws of the attached Tie Wrap broke immediately.
View detail
For fixing the cigarettes
I bought a new Ing's Cigar socket, but since it was not a Type directly attached to the Handlebar, I wore this Mount on the Handlebar and fixed it on it with a Double-sided Tape.
I am happy because I do not take space at Compact.
View detail
It is okay
I bought it to install the Digital voltmeter.
Size was also Small and Exactly
Somehow made it was a weak feeling.
If you make this, I felt it was cheaper a little more.
View detail
Car navigation system I bought it, so I found this item because it did not fit
Tanax Moto fizz CompactCase
I dated up from.
Reason,
IPhone 6s was Just size,
Car navigation system for Motorcycle system 5-inchesWide (X-RIDE RM-XR502MC)
I wanted to put in but I could not get in, I was in trouble.
So I found it on WEBIKE's Shopping.
Left is model number MF-4701 with Mount Kit
Right purchases only this time Digital Case.
It is good that there is universality like this (^o^)
You can use it carefully, and also handle mount kit
It is not wasted............
Gold and Ecology products as well.
View detail
For voltmeter installation
Thermometer and voltmeter etc. In order to install, I bought it.
We selected this product because the price is fixed for the firmly made Mount.
It looks tasty, but it has been around for 2 years, it is usable without problems.
View detail
Small Mountable for swinging
I purchased Repeat for ETC Antennas.
Lightweight Simple is convenient for mounting Small objects.
Screw's Length wants you to extend it by 5 mm.
I changed from attached Screw to Hexagon socket Bolt, Nut with Flange
View detail