Reviews
Tanax Moto fizz plate hook4
I purchased this product to install Side Back on my BirdCity125.
I think the quality is good and the cosmetics are good.
This is a product of Recommendation to Scooter.
View detail
It peels right off.
I stuck it on the Helmet in Upper Cowl of NC750X, but it peeled off soon due to the bumps.
(Of course, degreasing before applying and crimping afterwards)
The soft material makes it easy to apply, but I wish the adhesive was a little stronger.
I think there is no problem if it is a flat part or a curved part.
View detail
Cannot be installed on Crossfire125xs
There is nothing wrong with the product itself.
I had installed Plate Hook 3 on my SEROW250 and liked it so much that I purchased this product for my Crossfire125xs, but the License Plate Light interfered with it and I could not install it.
View detail
Quite tense when pasting.
[How is it used?
Since the Tank and Seat are in close contact, the longer the ride, the more fine abrasions will appear on the Tank.
I bought this product to prevent that. 2 sizes, LargeSmall, 3 sheets in total, can be shaped with scissors.
How was your experience with it?
It is quite thin in thickness but seems to be resistant to abrasions. After making a paper pattern to make a similar shape to the contact surface, it can be cut along the pattern to make a shape that corresponds to the contact surface. However, while it is easy to cut, this Seat does not seem to be able to protect against sharp objects. Durability is hard to say at this point.
How did it compare to other products?
This is my first time using this type of product.
[Points to note]
I bought the one with luster and carefully applied it to a glossy tank, but it has a few air bubbles, and as noted in the notes, there are wrinkles where there are curved surfaces. It seems that you don't need to worry about it if the shape is simple.
View detail
Transparent anti-scratch seal that can be easily applied
First of all, let me conclude that it is effective in preventing scratches and
Seal has good adhesive strength and does not come off.
Camping touring is quite popular these days. "Can use" Scratch-Proof Seal
I think so
The Week Point is that it's glossy and stands out a lot.
I think it's going to be by far the most popular!
View detail
The area is large and can be cut out and used sparingly.
I've used it on multiple places where loading hooks hit, and it's soft and won't scratch! View detail
Is good
I put it on to prevent scratches and scuffs caused by the attachment of Net and luggage, and also to prevent scratches on the fuel tank and Seat interference area.
[Color] It is clear, so it is not noticeable and will not detract from your motorcycle's design. It provides good protection.
View detail
I use it every year.
I use a magnet type tank bag for long touring, but the tank bag moves a little when it touches my body during getting in/out of the car and driving.
Is it good for the painted surface to leave it on? I think it is not good for the painted surface, so I use it every year around October at the end of long touring. The period of use is about 7 months for a large car.
I put it up in the garage at 15℃ or higher with the heater on, so that the seat is soft and the tank is not cold.
The large size is 90×60, so it is not so difficult to apply.
? The peel can be removed without much difficulty by lifting the corner.
After use, the tank is in good condition, with no wound on the tank and no adverse effects such as discoloration on the paint.
The product comes in one 180×120 and two 12 The product contains one 180×120 and two 12×90, which is very useful because we use four 90×6×90 in the Tank Bag. The product is very useful because it can be used for exactly two seasons since four 90×6×0 sheets are used in the Tank Bag.
Easy to use and good product for preventing scrubbing Wound.
View detail
Recommendation for Motorcycle with low Loading Hook!
This product is recommended for motorcycles with few loading hooks, such as sports type motorbikes. It is surprisingly thick and strong enough to resist bending even when tension is applied! View detail
Design makes it possible to choose any motorcycle for installation
I used it to protect my tank from scratches. It looks large in the picture, but the actual product is smaller than I expected, and my personal preference would have been for it to be longer horizontally.
The texture is good, but it was used with a little processing for the reasons mentioned above.
Because of its thickness, the adhesive strength loses its ability to peel off when the part has a tight bend.
I think it would be better if it was thinner, a little larger, and could be attached to any curved surface.
View detail
scratch-resistant
I bought this product to prevent scratches on my tank, and it looks good. View detail
Where it might get scratched.
[How is it used?
When I replaced the Handlebar, the lever seemed to hit the inner cowl, so I put it on to prevent scratches.
How was your experience with it?
It is highly durable, scratch resistant and will not peel off even after repeated car washes.
I think that it is convenient to buy it if you want to keep it as clean as possible because there are a lot of usages such as the prevention of the scratch of the Tank when Tank Bag is used and the prevention of the rubbing of the luggage fixation string.
[Points to note]
There are two types, glossy and non-glossy, so you should buy the one that is less noticeable to match your motorcycle.
Be sure to degrease well before applying.
View detail
I'm keeping the face of the exclusive.
It is used for the car body Left Side which tends to be damaged by jeans in the place where Seat bag and Tail cowl rub and push walking.
It is a relatively thick Seat with high transparency.
It's soft, so it tracks reasonably well and stretches a bit if you pull on it.
The adhesive strength is relatively strong, so it won't come off by itself, and if you want to remove it, you can do so without leaving any adhesive residue.
It will protect against frictional scratches such as scuffs on the seat back and tail cowl.
On the other hand, Scratch system scratches such as scratching with hard objects may not be able to protect the product because this product will tear.
I recommend 3M's Die KnockSeat for those areas.
(For better or worse over there, Material:Carbon Style, though)
By the way, it is convenient to have Masking tape to mold and apply this product to Beauty.
? Put masking tape on the part of the car body that you want to protect.
Write the type on the masking tape
? masking tape to the surface of this product.
? Cut to size
The moulding is completed with
This product can be reapplied a little at a time, so you can take a shot at it.
If you are unsure, use water paste.
Since Seat is colorless and transparent, be careful of fingerprint adhesion and air bites on the adhesive surface.
In general, Seat is easy to use as a Protector.
It is not so expensive, so you can try to put it on the part you are worried about once.
View detail
For fixing PannierBag
I bought this to create a place to secure the Belt on the back of my PannierBag. Installation was very easy. View detail
Very good product
Always stocked with scratch protection.Recommendation. View detail
It is highly protective.
It is effective in preventing scratches and scratches on the interfering parts of the Fuel Tank and Seat due to the installation of the Rear Cowl Net. [Color] It's clear so it doesn't stand out and doesn't detract from the design of the motorcycle. View detail
Thin, durable and unobtrusive
When I anchored the Seat, my inner thighs started to hit the side cover
Because it is a limited color of the last model, I did not want to put Wound on it I bought this product in a pack of three, between LeftRight+Tank and Seat
I installed it with the heat gun while stretching it a little bit, so I'm very happy with it without any wrinkles I was able to install it in the finished product
Who would think of a niche product like this? It was convenient and satisfying
View detail
It's inconspicuous … it's transparent …
I use it for the Heel Guard in my Off car
Material:The Aluminum Heel Guard makes white shoes and boots look black I wanted to keep the texture of aluminum, so I put "Clear" on it Use
I used it for CBR
I don't expect much in the way of durability, but I'm happy with its effectiveness for the purpose
View detail
high
The seat was hitting the tank [Color] The Clear paint is scraping off, so I decided to put it on
I tried to cut and paste it, but it's still going to be Wrinkle
But the price is high for just Seat
View detail
Used to prevent Tank's Wound
I installed it to prevent Tank's Small Wound.
I use it only with Magnet, but it can be used without being shifted. I like it like Design.
View detail