Reviews
Naples Hon
I can see why it has been a big seller for so long. View detail
Naples Hon
I see why it's been a big seller for a long time, I can see it and Design is good! View detail
Fits: YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA YZF-R1, YAMAHA FZ8S, YAMAHA FZ6R, YAMAHA FZ-6S, YAMAHA FJR1300, SUZUKI GSX250R, SUZUKI GSX-R125, SUZUKI GSX-R1000, SUZUKI GIXER SF, SUZUKI GSX-R1000, KAWASAKI ZX-6R, KAWASAKI ZZR1400, KAWASAKI ZX-6R, KAWASAKI ZX-6R
Good texture
I bought it because I liked the texture and design.
The moving part is fixed by Bolt, so it could be loosened by vibration, and it was necessary to carry a tool at all times. In windy conditions, the Motorcycle Cover could push it loose.
I don't put much force on the Arm Up, so the Right Arm was hard to Gap. I also used the seat Gold, but it did not improve much. I don't think it was loose due to weak tightening.
Visibility would depend on the compatibility of the Motorcycle, but I could not see directly behind me on the FAZER.
It is a Cool product and should be used well together.
View detail
Replacement from OEMMirror
EliminatorOEMMirror was replaced because it was not flattering.
The mirror area is also good and reduces the reflection of LED light.
View detail
easy to read
I installed the mirror on my MONKEY125 because it was hard to see. The rearward view is not only easier but also extended to the front, so I can use it very comfortably with less eye movement. View detail
Very good mirror
I acquired this Mirror quickly because the OEM one I had purchased with the CUB 50endless limited edition car had been replaced with a different narrow handlebar and ugly squares. Although it looks beautiful and has an off-road vibe, it is regrettable that it is so easy to move around by vibration and to see if there is a mirror outside in a better location. Ultimately, after obtaining the OEM mirror, it has been removed and is currently stored in the garage as a spare item. View detail
Neat appearance. Prevents rust caused by raindrops.
Removed the cowl mirror from CB400SB and replaced it with a handle mirror. At that time, I replaced it with TANA-X Shark5. I couldn't bear the uncomfortable feeling like a snail when I rode SUPER BOLDOR for the first time, so I spent a large amount of money to replace it with my favorite mirror.
However, because of the cowl, I could not easily install it, so I even bought a Tanax Adapter or something like that, and finally got it to fit nicely. Finally, I was able to fit this cap.
The product is good, of course, but I think it is a little expensive if it is stolen or falls off due to vibration. If it were a little cheaper, I would like to cover various places properly.
Please give us a discount. Also, please give us the smallest size.
View detail
Thanks to this, Shark mirror5 was installed in SUPER BOLDOR.
This time, I don't like the snail-like cowl mirror of CB400SB, so I decided to replace it with a handle mirror like Naked motorcycle.
So, first of all, which mirror would suit CB400SB the best? After much agonizing, I finally decided on the Shark mirror5 from Tanax. I had a hard time because the price was too expensive even though it was only a mirror, and I had a hard time here, too. (Sorry, it was much cheaper than Webike.)
Finally, I tried to install it, but it hit the cowl when I tried to put it on normally. I almost lost my mind, but since I had bought an expensive Mirror, I decided to go ahead and buy an OffsetHolder-45 (which was also too expensive!). In desperation, I decided to use Quantity:2pc. Set was bought, and Challenge was made to install it again.
As a result, thanks to this OffsetHolder, I was able to install it without hitting Cowl. It is like the OffsetHolder is attached to the original Mirror as well, so the Quantity:2pc. It looks like you are attaching OffsetHolder of Set, but it is attached in a nice way.
There are two reasons why we chose four pieces:One is to fasten iron to iron with bolt so that it does not slip, and the other is to use something like genuine leather or rubber to hold the bolt in place.:I wish it had been attached as a set, and the price is too high. However, I think the precision is fine and the construction is perfect. And since they are made by TANA-X, I don't think there will be any problem at all.
I have also tried to see if it would move with vibration after installation, but so far there seems to be no problem.
Personally, I think it turned out really cool. By the way, I spent a lot of money on MORIWAKI products to cover the hole in the cowl mirror. (I was already in a state of desperation.)
View detail
I think it is neat and stylish.
The snail-like OEM mirror on the cowl of the CB400SB was not very nice and I didn't like it, so I replaced it with a handle mirror.
After much thought and consideration, I finally settled on DAYTONA's Quantity:2pc. I narrowed it down to Mirror, which costs just over 4,000 yen for the set, or Tanax Shark mirror5. Price-wise, it was DAYTONA.
I am sorry, but Webike was not able to get the price, so I bought it elsewhere at a much cheaper price.
I was worried about whether replacing it with a Handle mirror would contact the Cowl since it is a SUPER BOLDOR, but since no one has mentioned it in the Reviews so far, I don't know and decided to take the initiative and give it a try.
As a result, it was impossible. but with an Adapter, it was Large sturdy. Expensive MirrorQuantity:2pc. Set、AdapterQuantity:2pc. Set, CapQuantity of screw:2pc. Set, with the original Mirror hole Cover (MORIWAKI), it became the most expensive Mirror in my Motorcycle history.
I think it took more than an hour to adjust this and that, but I think it turned out really cool.
Large Satisfied
View detail
Inexpensive and good
When I replaced the OEM up type separate handle with the HURRICANE Pipe Handlebar KIT, I also replaced the long OEM cowl mirror that I did not like with this mirror.
Although it is harder to see backward than the OEMCowl mirror, I am satisfied with the mirror because it is not bad looking, lightweight, and has a wide mirror surface.
An adapter was included to extend the bracket and make the rear more visible, but I did not attach it because I do not like the way the Mirror extends beyond the Bar End.
By the way, to change NINJA1000 to Handle mirror, Clutch/Brake Clamp with Mirror hole of Z1000 is required.
View detail
TANAX OFFSET HOLDER 45
Thank you so much for the quality and delivery. After the release of the new Monkey 125, it seems that this part is the part that can be used to counteract the extreme vulnerability related to the side mirror visibility. Due to the recommendation from other Monkey users, I will purchase it without hesitation and use it well. -------------------------------------------------- -------- Thank you so much for the quality and delivery. After the release of the new Monkey 125, it seems that this part is the part that can be used to counteract the extreme vulnerability related to the view of the side mirror. Due to the recommendation from other Monkey users, I will purchase it without hesitation and use it well. Powered by Google Translator View detail
Thanax M10 mirror bolt cap
Quality and Texture Information The feel of the plastic product is clean. Products purchased together TANAX: Off-set Holder 45 is easy to install.
If you install it alone, you will be able to prevent problems that occur due to the bolt fixing part being exposed at the top.
Webike delivery and packaging are in excellent condition. Thank you. -------------------------------------------------- -------- Quality and Texture Information The feel of the plastic product is clean. Products purchased together TANAX: Off-set Holder 45 is easy to install. If you install it alone, you will be able to prevent problems that occur due to the bolt fixing part being exposed at the top. Webike delivery and packaging are in excellent condition. Thank you. Powered by Google Translator
View detail
It is easy to install. Anyone can install it in 1 hour.
Installation is easy with only 4 bolts. The mirrors are of a spec that will not glare at the lights of following cars, and the overall high-end look is perfect. View detail
Adjustment
I personally like this Mirror design because it is easy to match with the car body.
This is the first time I have tried to use TurnerSpec. but the adjustment is Large strange. when I try to adjust the Lens, the Turner part is pushed and turns before the Lens part.
I understand that it is natural in terms of functionality.
If the car is to be gapped on the road, we are looking at OEM diversion.
View detail
it's recommended
The glare from the ledHeadlight is also much reduced and easy to see at night. View detail
Mirror
Plating Mirror looks good but I am concerned about rust and peeling, so it was nice to have Black. View detail
Mirror by Yamaha
This is something that is inevitably needed because Yamaha's Mirror uses Opposite Thread Screws. View detail
Fits: YAMAHA XSR900, YAMAHA XSR700, YAMAHA MT-10SP, YAMAHA MT-10, YAMAHA MT-09SR, YAMAHA MT-09, YAMAHA MT-07, SUZUKI ST250E, SUZUKI KATANA, SUZUKI GSX-S750, SUZUKI GSX-S1000, SUZUKI GSR250, KAWASAKI Z900RS, KAWASAKI Z900, KAWASAKI Z800, KAWASAKI Z650, KAWASAKI Z250SL, KAWASAKI Z250, KAWASAKI Z125PRO, HUSQVARNA Vittopilen 701
I purchased 2 of this product. However, it is oriented in the same direction. Does this product have no distinction between lef
I purchased 2 of this product. However, it is oriented in the same direction. Does this product have no distinction between left and right? View detail
Buy 2, guys
You're purchasing a set of ONE unit. I made a mistake buying only one thinking it comes as a set of 2 units. Don't make the same mistake as I did. As for the product itself, no complaints - it's sturdy and good-looking. View detail
I like the blue lens and this shape.
We selected Napoleon OnMirror because there was no other mirror with a blue lens that was slightly parallel to it.
Quantity:Pair (for Left and Right) Two of these products must be purchased for installation in a
The installation was easy and quick with Bolt On, the position adjustment is wide, and the visibility is fine.
The vibration caused by the vibration is more difficult to see at high speeds than OEM products, but I think it is relatively better than other brand products.
I think it would be good if you don't want it to be Design-like and tactile.
View detail