Reviews
A little Custom
Used for DL1000 V-STROM250.
I wanted to customize it a bit, so I decided to make an affordable Mirror replacement.
It looks different, but weighs less than Normal mirror.
So there may be some changes in Handling.
Rear visibility is fine while driving.
View detail
Thanks to this, Shark mirror5 was installed in SUPER BOLDOR.
This time, I don't like the snail-like cowl mirror of CB400SB, so I decided to replace it with a handle mirror like Naked motorcycle.
So, first of all, which mirror would suit CB400SB the best? After much agonizing, I finally decided on the Shark mirror5 from Tanax. I had a hard time because the price was too expensive even though it was only a mirror, and I had a hard time here, too. (Sorry, it was much cheaper than Webike.)
Finally, I tried to install it, but it hit the cowl when I tried to put it on normally. I almost lost my mind, but since I had bought an expensive Mirror, I decided to go ahead and buy an OffsetHolder-45 (which was also too expensive!). In desperation, I decided to use Quantity:2pc. Set was bought, and Challenge was made to install it again.
As a result, thanks to this OffsetHolder, I was able to install it without hitting Cowl. It is like the OffsetHolder is attached to the original Mirror as well, so the Quantity:2pc. It looks like you are attaching OffsetHolder of Set, but it is attached in a nice way.
There are two reasons why we chose four pieces:One is to fasten iron to iron with bolt so that it does not slip, and the other is to use something like genuine leather or rubber to hold the bolt in place.:I wish it had been attached as a set, and the price is too high. However, I think the precision is fine and the construction is perfect. And since they are made by TANA-X, I don't think there will be any problem at all.
I have also tried to see if it would move with vibration after installation, but so far there seems to be no problem.
Personally, I think it turned out really cool. By the way, I spent a lot of money on MORIWAKI products to cover the hole in the cowl mirror. (I was already in a state of desperation.)
View detail
Inexpensive and good
When I replaced the OEM up type separate handle with the HURRICANE Pipe Handlebar KIT, I also replaced the long OEM cowl mirror that I did not like with this mirror.
Although it is harder to see backward than the OEMCowl mirror, I am satisfied with the mirror because it is not bad looking, lightweight, and has a wide mirror surface.
An adapter was included to extend the bracket and make the rear more visible, but I did not attach it because I do not like the way the Mirror extends beyond the Bar End.
By the way, to change NINJA1000 to Handle mirror, Clutch/Brake Clamp with Mirror hole of Z1000 is required.
View detail
it's recommended
The glare from the ledHeadlight is also much reduced and easy to see at night. View detail
I like the blue lens and this shape.
We selected Napoleon OnMirror because there was no other mirror with a blue lens that was slightly parallel to it.
Quantity:Pair (for Left and Right) Two of these products must be purchased for installation in a
The installation was easy and quick with Bolt On, the position adjustment is wide, and the visibility is fine.
The vibration caused by the vibration is more difficult to see at high speeds than OEM products, but I think it is relatively better than other brand products.
I think it would be good if you don't want it to be Design-like and tactile.
View detail
Amazing built quality.
The workmanship for this mirror is marvelous. Would be better if rubber bushing is included in the package so it would help to minimise the vibration that is being sent to the mirror when travelling at higher speed. Clarity would be compromised with the Speed above 100km/hr. View detail
It was a little short!
After installing Extension India on PCX, Mirror and Extension India interfered with each other, so I bought this as a countermeasure. I had no choice but to adjust it by shifting the Extension India, but the interference could not be improved, so I decided to ride it as it is. I will buy OffsetHolder45 later. View detail
For those who want to increase visibility...
It has been on since I bought it and I was going to replace it as soon as I could, but it looks relatively good, has good visibility because it is MirrorLarge, and depending on how you mount it, it doesn't stick out more than a handlebar. ????? So I'm using it as it is. View detail
I generally like it, but...
CT125 OEMMirror is hard to see, so I replaced it, and it looks Wide with R800 (note the distance!). No blurring due to vibration.Quantity:Pair (for Left and Right) The overhang of the "L" is less than OEM. The Lock nutCap at the root is Large tight & loose. I don't like the silver color part which is the accent when viewed from the front, so I hid it with a Round Type Seal (5cm diameter). View detail
quintessential old shopkeeper
No problems at all with the texture and feel.
I marveled at the quintessential Mr. Tanax, who has been making them for decades!
I have installed this Mirror on my GB350, and before this Mirror, I had installed the one from an unfamiliar manufacturer and the one from a well-known manufacturer.
Loose immediately, Motorcycle left for a week to loosen….
Design, it was a problem before texture
It's just … wild!
It's kind of fat all around.
I wish it were thinner, though, as it might cause loosening or blurring.
Well, I don't mind once it's running.
View detail
I need to buy two
Quality and texture information The paint finish is clean and good It certainly looks good on the sense of use Product to Buy Together Product # BCM-10 Installation difficulty easy Perfect for cost performance and comparison monkey 125 WeBike packaging is always great, arriving in a week for delivery and packaging Advice Since the screw is in the forward direction, it should be installed after checking carefully If you install it incorrectly, the screw line may be disrupted and the package configuration is composed of one, so please buy two and save time and money Many people buy only one View detail
There's a lot of freedom
I liked the flexibility of the angle etc.
The mirror surface color is also cool. The weight is a little heavy, but I guess it can't be helped to make it firm.
View detail
Fits: KAWASAKI Ninja1000SX, KAWASAKI Ninja1000SX, KAWASAKI Ninja1000, KAWASAKI Ninja1000, KAWASAKI Ninja650, KAWASAKI Ninja650, KAWASAKI Ninja650, KAWASAKI ER-6f, KAWASAKI ER-6f, KAWASAKI ZX-6R, KAWASAKI ER-6f, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-25R, KAWASAKI Ninja250SL, KAWASAKI Ninja250, KAWASAKI Ninja250, SUZUKI GSX-R1000, SUZUKI GSX-R1000
Installation is not quite right
I didn't like the OEM's tactile Mirror so I replaced it. As a result, I am satisfied with the new Mirror because it is easier to see the back of the car and looks better than the OEM Mirror. The installation was not so easy to understand. View detail
Style is very good, but...
I fell in love with Style and bought it!
The handlebar area looks very sharp and good, but the narrower width of the upper and lower sections makes it harder to see than the OEM.
In my BOULEVARD, the vibration causes the rear vehicle to shake when the speed exceeds 70 km/h.
Blue lens is quite good.
View detail
Texture
The quality is excellent. As other reviewers have said, the weight of the Single Item ensures visibility and does not shake due to vibration. Of course, the Mirror section is smaller than the OEM section, so visibility is lower. However, this is not a problem for me, as I can adjust the size of the Mirror section to my preference. View detail
Design is good, but you can't see the back
When I replaced the handlebar, the angle of the BAREN Mirror Mirror I had been using was no longer suitable, so I searched for a similar Mirror of a Small Type and decided on this product.
In terms of design, it is nice, reflecting and not conspicuous.
However, you cannot see the back.
I wish the bracket was 5cm longer.
Also, the narrow width of the upper and lower sections makes it difficult to see the back of the car on slopes. I wished the upper and lower widths were 1 cm wider each.
I am well satisfied with it myself, but I would not recommend it unconditionally to others in terms of visibility.
View detail
it's recommended
The glare from ledHeadlight and other lights is also reduced, making it much easier to see at night. View detail
Overall a good Mirror
We have a small parking space for bicycles, so we need something that can be folded up easily, but we also want to be particular about the design. [Color] Clear was this Mirror.
The ADV150's style is comfortable and there are no problems with rearward visibility. There is a little bit of shaking while driving. The Mirror is a good Mirror overall, but after the second run, I heard a shaking sound from the Left Side … The mirror surface moves when I touch it with my finger … I guess the glue was not applied properly. I had no choice but to buy a new 1 pc. (Right Side has no problem)
Other than that, Mirror is satisfactory.
View detail
Dio110
Latest Dio110Basic (2023) The windshield can be installed together with the WindowShield of the Asahi Windshield.
Screw is 10mm.
View detail
Just right for Scooter.
Good angle adjustment for the price.
I was concerned about visibility due to Design priority, but visibility is not as bad as I expected.
Note that the angle adjustment on the Mirror side and the bar angle are not stepless.
View detail