Reviews
Yamaha's Opposite Thread Screw A must-have for cars
I purchased this product when I switched to Napoleon OnMirror because my OEMMirror was rusting.
The Mirror position is slightly higher, but it was successfully installed.
View detail
It is a must for Yamaha cars.
It is just a conversion Bolt but it scratches easily. monkey Wrench should not be used. It gets scratched easily. View detail
Scratches easily
Purchased for Mirror replacement.
I had heard that it was prone to scratches, so I worked with caution, but the scratches were firmly in place.
It's a cheap product, so maybe it can't be helped, but I'd like it to be made a little sturdier.
View detail
I'm happy with how high Mirror can be positioned.
I bought and used the Tanax OffsetHolder and Cap to raise the height of the mirror, which made it easier to see behind me. I've been using my eyes nervously and had a lot of eye fatigue, but that seems to have lessened considerably! View detail
It can be used normally
I used it to put Mirror on the Other Brand Product.
It can be used normally.
Good thing it looks so OEM-chic and unassuming!
View detail
Good texture
Bought it to install the Mirror for the SR400 on the CD125TBENLY50.
I was able to install it with no problems.
It can't be helped, but be aware that the height of the Adapter makes the Mirror more expensive.
For that reason, I think the Mirror Bracket should have a lower height.
View detail
Is this what it looks like?
I'd like you to release the Black Anodized in Aluminum.
Also, Quantity:Pair (for Left and Right) I'd like to see the total weight published.
Previously. It's about making the bike lighter and losing weight yourself! And there was an article about...
View detail
tightly packed
It is good if it becomes a little more Smallish, but because it can be fixed to Handlebar firmly I am very happy with it and it is stable even with a large piece of hardware installed View detail
Nice Screw Adapter
This TANAX Left-Handed Screw Adapter is very useful. It allows me to lift up the mirror a little bit, and to allow me to install a mount between the mirror and the screw adapter. View detail
Purchased for bulk by Mirror exchange
When replacing from OEMMirror to Mirror of Other Company Product, the height lowered and it became hard to see, so I bought it for the bulk of height earnings. It was Mirror of Japanese Vehicle Inspection Correspondence, but if you have Turner it may be useful if it is used? Because it is a product that shows its effect when you touch it Fortunately I have not confirmed the effect yet and I will keep 3 stars.
View detail
Product itself is not bad
I attached it to the MONKEY's normal mirror but the height became high and Balance became worse 2 - I think that the product itself is not bad it was removed in 3 days View detail
It is a good product without particular problem
I bought it for Opposite Thread Screw for YAMAHA car to be Normal Thread Screw but because it was Opposite Thread Screw → Normal Thread Screw for explanation, I thought that Opposite Thread Screw would be Normal Thread Screw, Normal Thread It was to make Screw an Opposite Thread Screw. I would like you to clarify the explanation a little more.
I have not seen it well though it is bad... Hereafter care.
View detail
Since the position of the Mirror was low, a Spacer is purchased in order to make it high.A size is the same as the conversion Adapters of the company, and it mmUP(s) height 20 times.A screw hole is a sense-of-incongruity pear, even if it attaches, since i
Since the position of the Mirror was low, a Spacer is purchased in order to make it high.A size is the same as the conversion Adapters of the company, and it mmUP(s) height 20 times.A screw hole is a sense-of-incongruity pear, even if it attaches, since it is the same brand item as a Plating and the two-kind
Mirror of a Black with a 10-mm right Screw.The low Mirror became legible by having mmUP(ed) 20 times.since -- One more piece is connected. -- although intensity is anxious -- -- good -- bad -- a Mirror adjustment Spacer.It will be the useful kana if there is a Spacer (not only 20 mm but 30 mm and 40 mm).
View detail
a 10-mm positive Screw is only made high 10 mm -- け. However, since it hits a Chalk lever in the case of ZRX1100, a Shark mirror is not attached and made. There is no difficulty with a 17-mm Socket and a Torque wrench in attachment.
a 10-mm positive Screw is only made high 10 mm -- け. However, since it hits a Chalk lever in the case of ZRX1100, a Shark mirror is not attached and made. There is no difficulty with a 17-mm Socket and a Torque wrench in attachment. View detail
It was used as a Stay for KDX125 left Mirrors. Although it becomes with some Offset a little, it can be used ordinarily. It is satisfactory as substitution of an original manufacturer's product.
It was used as a Stay for KDX125 left Mirrors. Although it becomes with some Offset a little, it can be used ordinarily. It is satisfactory as substitution of an original manufacturer's product. View detail