Reviews
I put it on to keep the bugs away.
With OEMScreen, the insects hit my neck, so I wanted a slightly largerScreen and chose VS-14.
The objective was successfully achieved and the insects no longer collided with the neck.
It came with a warning to do the Cover when parking in direct sunlight, but honestly, it's a hassle and I'm going to try using it without it until I have a problem.
Is there a real problem or not...?
View detail
Windshield effect is best, but
Installation was easy, but if you make a mistake in the setup, you will end up with minor scratches on both ends of the lower inside of the Shield.
The running and wind protection effect is very good.
However, the Shield is so close to my face that when I apply emergency braking, the Shield tip almost sticks me in the face.
If you have a Helmet Shield, you are safe, but if not, you will injure your face and eyes.
We are considering installing a molding around the Shield as a countermeasure.
View detail
Fits: SUZUKI BURGMAN200, YAMAHA NMAX, YAMAHA NMAX150, YAMAHA NMAX155, YAMAHA NMAX
so-so
It is not as good as the Handlebar Cover in winter, but it is reasonably windproof, and if used with the Grip heater, the fingers are not as cold.
It was easy to install and because it's a BURGMAN 200 OEMScreen, it's comfortable with no interference.
View detail
Installed on JA45
Although it is designed for JA60, it can be installed on JA45 as well.
I'd have to get a separate Bolt for just the 1 pc, though.
View detail
Fits: HONDA CT125 CT110 HUNTER CUB, HONDA CT125 CT110 HUNTER CUB
It suddenly got cold.
I bought this for protection against the cold because it suddenly got cold. I still need a leg shield for CUB. View detail
Fits: HONDA SUPER CUB 50 , HONDA SUPER CUB110, HONDA SUPER CUB110
Short Visor for appearance
I saw a SUPER CUB110 with Short Visor installed in town and it looked good, so I bought it based on the reviews.
Installation is so easy that even a beginner can install it without looking at the instruction manual as long as Spanner is available. (about 30 min. working time)
However, JA59 has a Mirror position of Quantity:Pair (for Left and Right) Since it is asymmetrical, I had to be careful to straighten the Screen.
The look and feel of the installed product has changed considerably, giving it a stylish look and feel.
Since it is a Short Type, the wind naturally hits the face, but does not directly hit the body, so it also serves as a windbreak and reduces fatigue when running.
However, as a precaution when Visor is installed, if it is placed outdoors under the blazing sun in midsummer, the windshield is a convex lens, and like a magnifying glass, it may reflect sunlight and melt the area around the Meter.
After installing and running the system, I found that the Instruction Manual was very easy to understand, and even a cloth cover was included to prevent reflection and light collection.
View detail
Fits: Others 50cc-750cc for each company/Pipe handle
Asahi windshield
Very good windshield well made fitted to a Royal Enfield 500 EFI classic 2016. Fitted on my own in about an hour. The cloth skirt has no holes in it you have to make them your self I marked the holes against the holes in the screen with a pen and got a small screw driver hot to burn the holes in I have seen people folding material in half a trying to cut it no a good idea burnt hole are dead size supper fast shipping to UK 3 days very pleased with it View detail
Fits: HONDA CT125 CT110 HUNTER CUB, HONDA CT125 CT110 HUNTER CUB
Leg guard with material flexibility in proportion
Personally, I only do this to the extent of OffTrek at most ….
I ordered this Leg guard to improve windproof performance.
It is hard to understand even if you check the website, but the upper side is fixed to the H-shaped Carbon-like GuardBody, and the upper side is fixed to the horizontal Gold Bracket with the Bolt on the upper side of the frame cover. The lower side is fixed to the U-shaped resin parts on the under frame with the Bolt.
We have a Daytona & Phi; 22.2mm (7/8in) Engine Guard, so it is not possible to fix it with these U-shaped plastic parts.
SpaceMount (for Bicycle) & Phi;22~25mm made by Miknowla were lying around in the stocked materials, so we used these.
I used to have a forced air cooling fan on my Ural Sidecar.
Clamp the bolt to the Pipe with a bolt fixation, and you can freely place a reasonably strong bolt hole, which is just as well, because it is convenient.
Bolt fixed without bridging
Quantity:Pair (for Left and Right) It would be nice if we could both take advantage of the existing holes, but … it's not that convenient to go that farω.
Since I don't care about irreversible processing ΦDrill with a 6.5m drill blade and fix a single hole quickly with the supplied bolt.
The carbon-like resin body also flexes without difficulty, making installation perfect.
Style also has good wind protection. I would like to try running in the rain, but generally it looks good.
It will be interesting to go on a super long touring trip down the road again as well as the high-speed maneuvering with the Trailer load that I have been into recently!
View detail
Reduction of wind hitting the body OEM?
latest (MODEL 2023) It is installed on a Dio110Basic of
Napoleon OnMirror with this windshield (10mmType) Both of the two can be installed without any problems.
It could be a little taller, but it does not have a Windshield wiper,
If the height is higher than this, water droplets will block the forward view on rainy days.
The size may be exquisite.
View detail
Effective
Dio110Basic (Model 8BJ-JK03) The product can be installed without any problem on the
The height of Window is not as high as I expected.
View detail
Rain hits the Helmet, but ….
If it were 5 cm higher, the Helmet would not be exposed to rain, but maybe the increased resistance would make the Handlebar unstable.
Therefore, it is good.
View detail
Fits: HONDA CT125 CT110 HUNTER CUB, HONDA CT125CT110 HUNTER CUB
I wanted something a little more Large.
I am Large satisfied with the construction, but I wanted more height.
From a design standpoint, it would have been cool to have this height, but from a storm effect standpoint, it would have been nice to have a little more height.
Shield extensions are available at Amazon and other places at a lower price, but they did not look cool, so I did not install them.
We are considering responding without Seat's anchor.
Currently, the wind is blowing around the direction.
View detail
Design is good
I did not expect much wind protection, but sure enough.
However, it is different compared to without the windshield, and I feel that driving in a headwind has become more stable.
There may be a rectification effect.
Installation is easy
It would be a good introduction for DIY beginners, since it would be a waste to pay for labor to have it attached.
Spanner is a Quantity:It is better to have 2pcs.
View detail
The wind protection effect is there.
I bought it to protect against winter driving winds. Although it looks ugly, I think it does a good job since it is not directly exposed to the driving wind. View detail
No more wind in my hands!
I had been using a Handlebar Cover to keep out the cold during the winter, but I thought it looked too much like a business motorcycle and wasn't good enough.
Installation was quite easy and took about 15 minutes without much reading of the simple manual.
The effect of the installation can be felt immediately, and the wind on the back of the hand can be reduced considerably (with some entraining wind).
This performance is very much appreciated at night when the wind is still chilly, even though it is spring.
We have not done any off-road driving where there are stones or branches, so the protective performance is unknown.
Also, in terms of design, since the body is made of transparent resin, it can be used as a material for off-road motorcycles.:It is good that it doesn't look like a Race ish outfit like PlasticHand guard.
I found it very suitable for CROSS CUB's Taste.
View detail
Meter visor only
Unlike the Universal Product for Handlebar Mounting, the Fork is mounted with a vehicle model Exclusive Bracket, so there is no need for delicate alignment and no particular confusion. 。 Fork side Holder and Visor side Bracket are Quantity:Pair (for Left and Right) Since they are connected by one Bolt at a time, it is easy to adjust the angle before tightening this Bolt.
The bottom line? It's the look, but I think it's a design that doesn't destroy Bolt's Image. 。 I feel that the front/rear balance is not so good when the Rear Carrier is attached and the Bag is carried on Both Sides, but I don't particularly care about it, so it is OK.
As for wind protection, the electronic products around the Meter and Handlebar are protected from wind, rain, and insects while running, but the Helmet is normally exposed to wind, and the wind that gets caught in the Helmet hits my stomach. 。 It's like the chest is protected from the chin while protecting the Meter. 。 The OEMShield of the VALKYRIE I had before the BOLT Shoulder Bag was a large size so that the wind did not hit the Grip as well as the body, so I felt a large gap, but I wanted to put a small size Shield on the BOLT Shoulder Bag. I am not dissatisfied with it because I want to put a smaller Shield on the BOLT Shoulder Bag and above all, the product name is Meter visor.
View detail
Fits: KAWASAKI NINJA400, KAWASAKI NINJA250R, KAWASAKI NINJA400, KAWASAKI NINJA250R
It looks good.
[How is it used?
I installed it and drove it for a day.
Was the one you received as per Image?
Very light and colorful. [Color] Very good with Smoke.
Was the installation difficult?
I was able to install it with a hexagonal LUNCH like the ones that come with assembling furniture.
It is a little hard at first, so you need to be careful not to lick the Screw.
Stick the hexagonal lunch into the screw and turn it half clockwise. And you can remove it easily.
When you remove the Screw, you should hold it down so that you don't drop it because the Mirror will come off immediately.
Now all you have to do is fit the Mirror you purchased and close the Screw.
How was your experience with it?
When I install it, it is a little bit ? bent. But I don't think it's a problem for Spec. If it becomes a concern or loosens, I'll put a rubber between them.
I thought it looked a little long before I bought it, but when I saw it in person I didn't care that much. It looks so much cooler now.
The windproof effect seems to be there compared to the OEM. I think you can feel the difference when you ride at high speed.
I bought it to change the look of the house and I am quite happy with it.
[Included Parts:were they on?
Body、Screen Cover、Instruction Manual
[Was there anything that disappointed you?
It is a pity that it rattles a little when it is installed.
Also, the Instruction Manual doesn't mention what tools to use etc., just remove the OEM and follow the same procedure. It just says.
It's not that difficult a task, so it's not necessary, but it would have been better if it had been mentioned.
View detail
Fits: HONDA TACT, HONDA TACT, SUZUKI ADDRESS110, SUZUKI Address125
Vehicles equipped with DAYTONA's Screen are also acceptable.
Since I am installing a DAYTONA Screen, I am not using the Adapter that comes with this product, but using the Adapter that came with the Screen! 。 Therefore, I think that it has risen a few centimeters above the original installation position and the entrained wind has increased somewhat.
Even so, the effect of the Knuckle Visor is gratifying even if the wind entrainment is increased because the way to hit the wind is completely different when the hand is shifted to the outside while running. Especially since I use it for commuting. "Winter & Rain. I'm even more thankful for it because I use it in the worst situations.
However, if I say it is natural, it does not cover the hand like Hand warmer, so if I compare it with that, the effect of cold and windproof is inferior. This is good for me who is concerned about the appearance and hygiene!
View detail
Wide.
The look and feel of the design is very wide and the style is more parenthesis-like, and since it is an exclusive design, there is no need to process it. View detail
It was better than I thought it would be.
Since it's a meter visor, I thought it would only be a dress-up, but when I put it on, it didn't have a dramatic rectification effect, of course, but I could still feel the change in airflow compared to when I didn't have it on. It would have been better if it had been longer, but I'm glad I bought it as a dress-up, for its effect and for its texture. View detail