Reviews
Happy!
There's less wind in my lap.
Winter works sober!
The product system is quintessential! One word! It's easy to install. You've thought this through. I think
You don't see a lot of people wearing it, but it's one of the products I'm glad I bought.
View detail
Excellent wind protection
I bought it for the New Year's Eve Soya Cape for wind and cold protection.
All Screens may be the same, but they are a bit cumbersome to install.
It is installed on the underside of the headlight with the Mirror and the friend tightening.
All you need is a Phillips Screwdriver and a Hexagonal Wrench and you're good to go.
It is quite effective as a wind and cold protection.
You don't have to lie down to let the wind pass over the Helmet.
So I think it's close to windless.
The crosswind was so strong in Hokkaido that I couldn't tell if there was no wind or not (laughs).
The cold wind didn't hit my body, so it worked quite well to keep me warm.
If I were to raise Demerit, I would say two things:looks and air resistance.
As for the appearance, the impression of the Small and cute LITTLE CUB is completely changed because the head looks Large.
As for the air resistance, I felt that the Engine was working a little harder than when I didn't have the Screen because of the Large Screen.
And there's Demerit, but the heady LITTLE CUB is cute too, and I never felt like I couldn't move forward at all due to air resistance.
To begin with, I couldn't get that much speed in Hokkaido in winter (laughs).
It was an excellent screen for wind and cold protection.
View detail
It's pricey.
The good thing is that it can be installed at the same time as the pcx Body Mount Shield.
The Right Side doesn't interfere with the shields, but the Left Side hits when fully locked, so
It is Minus in that respect.
I wish the bottom side was a little larger, but it is OK because I can avoid the wind and rain.
View detail
Dramatic improvement in wind resistance
I purchased this product to reduce the running wind on my Jixxer
The delivery time was guided to take about a month from the time of order, but it actually took about two weeks from the time of order
Installation is very simple and easy Car Both Sides ScrewQuantity:2pc removal,?ScrewQuantity:Tighten 2pc, install Screen Bracket, tighten 4 screws, Screen It took me about 15 minutes to complete the job with a 3 footpeg of installation of
The following three points are important for installation
Need #2 Phillips Screwdriver
Overtightening the Screw on the Windshield interferes with the Bracket
When removing the screw on the body side of the car (7,000km), the screw side has no rigidity and the screw is not rigid enough You must carefully remove it with a high-precision tool
With the Visor installed, the height is increased by about 9cm compared to the OEM, and the wind resistance is even better than it looks It was done There is no collapse of design as it is a dedicated product, but rather, it is a product that has become better in Parenthesis It seems It also increased the Handlebar stability at high speeds The height as well as the width of the car may have had a rectification effect
The price seems a bit high, but it is a good quality product with Polycarbonate It's worth the purchase because it's Exclusive Design and it's expected to be effective
It is important to note that the screen changes when storing a vehicle in a sunny location You will need to cover it with the cloth bag that came with it to avoid the possibility of (If you can keep out the sun, buy some at Toweletc.)
In general, it was a good product and I can highly recommend it to anyone who drives fast with a Jixxer Owner!
View detail
Price is high, but performance is expected
I commute to work on the PassPass every day with my Jixxer for about 60km round trip When it is a windy day and there is a headwind, the Grip force of the Front is reduced to the extent that the Front fork is extended So, I decided to buy it to improve it It's not ready for use yet, but it's an Exclusive Design in Polycarbonate It's not ready for use yet, but it's an exclusive design in Polycarbonate Installation is only possible with the #3 Phillips Screwdriver, so the We are looking forward to the performance and serviceability It's a bit Neck that it takes more than a week to deliver because it's a made-to-order product View detail
Fits: KAWASAKI NINJA400, KAWASAKI NINJA250R, KAWASAKI NINJA400, KAWASAKI NINJA250R
Wind protection is a nice touch
Installation is easy
It was just a bit thinner than the OEM Screen, or it rattled
I used a 1mm rubber sheet to adjust it
I think it's just a little longer than the OEM, but it's more windproof
[Color] Smoke was darker than I expected I guess that's okay because it looked different
View detail
Small and well-designed
I bought it because I like the design in my opinion!
I also considered the OEM, but I liked this one better (this part is my personal feeling, so I have my objections) (If you are a person, please go through it)
Also, it was made by Asahi Windshield, a company with a long history in windshield design
Installation is easy with a 10mm glasses wrench and a 3mm loofahgon wrench is
(In my case, I had to relocate Antennas for ETC and it took some work
As for the wind protection performance, up to 70~80km/h, the wind at the chest seems to be weak However
With Helmet with Visor, the wind hit the ground more strongly, and the Helmet's Wind Cutting sound is Large
It seems to have become
I'm just guessing, since we haven't driven on the highway yet, but I'm guessing that the air will be flushed further upward at high speeds, so we'll be able to get a better idea of what to expect
I expect it to be comfortable That's what I'm hoping for at the moment
Sorry to be halfway through this report, but both Size and Design are well suited to XSR I think it looks good on you
If you're looking for something easy and stylish, I thought I'd recommend it
View detail
Fits: Others 50cc-750cc for each company/Pipe handle
Used in YB50
I bought it to use with my YAMAHA YB50
It's a large-textured windshield, but it's very functional and looks great
It's especially useful in the winter, when the wind gets cold
View detail
Fits: Others 50cc-750cc for each company/Pipe handle
Retro feeling suits you
This is the Motorcycle windshield of childhood? It is attracted to Retro feeling and purchased and installed in Eliminator 125 and used 1 Season.
Installation of Arm to Handlebar is position adjustment ? Even though angle adjustment is only fixing 2 places with simple UGold thing, Quantity : Pair (for Left and Right) I was somewhat cautious in aligning the alignment of. (Because it is Universal, I think it is due to making it a gold item or simple)
Canvas was easy to install without problems with the position of the canvas and headlight, Blinker lamp which I was worried about before purchasing.
It is an impression after use.
Short Type but Eliminator 125 dedicated to the lower road thinks the windshield effect is sufficient.
I saw some of the canvas rubbed in 1 Season and the hole opened so I think it would be good if you can exchange canvas only by cancellation.
Partial Arm installation etc etc. We note that Rust is likely to occur in the Gold item of.
View detail
very good!!
I really like it. Easy to assemble. However, it is a little difficult to assemble correctly. But I do not think there is as good a windscreen as the Asahi windscreen. And I think it's very flexible and you do not have to worry about breaking down. View detail
PetitCustom
Easy to follow and feel good without interfering with Knuckle Garden. Did the wind flow go up slightly !?
Rainy days are still unpruned.
View detail
Classic to keep hands from rain breeze
Knuckle visor, which was used from the front mold LEAD in the same way,.
Easy installation, shape is also good Large changeable. Only worry about degradation of Double-sided Tape.
View detail
No. quotient ProductNo : AD-21 also attached to LITTLE CUB
Some people mistakenly impressed CUB exclusive Shield on the product page of AD - 21 so that there is no misunderstanding.
AD-21 (SmokeShort Visor for ADDRESS V 125) I will write about.
For this ADDRESS V 125 【With condition】 Can also be installed in CUB, please see the picture.
【Condition 1】 M10 of M10 Standard Thread Screw is attached
[Condition 2] Adapter that converts M8Tap to M10 for Mirror above is also attached and the height is increasing
[Condition 3] Offset mirror size between Mirror with Offset mirror adapter (I am Posh Face Commercial Product No : I used 000720-06)
We realized it under the above conditions.
As Offset mirror adapter is high like stupid, it is about 16,000 including Mirror & Short Visor to do so far.
I was thinking about the windshield for CUB that was only vertical and transparent, I thought about it, I became a pillar and tried TRY and it was Large Correct !!!
It seems that the inclination is slightly asleep rather than attached to ADDRESS V 125, but looks are tightened, and cars are also satisfied as if they look like Large grade.
The only drawback is "It does not look like CUB" Is the degree getting worse and steadier? (sweat;)
* Those who will be referred to please be at your own risk.
View detail
Fits: HONDA SUPER CUB110, HONDA SUPER CUB 50
Just a good Length, windproof effect
Installed on SUPER CUB 110 JA 10
Before this was MADMAX's 2000 yen Screen
Since this was too severe I immediately ordered this immediately
If you buy this from the beginning ...
Screen of Asahi draft shield was attached even ADDRESS V 125, DIO 110, LEAD 100
So I knew the goodness of quality so buy without hesitation
Short Visor for JA 07 and JA 10 OEMOption Length per the middle
People who are not good at Screen which is too long
Exactly to that person
The wind up around the chest is almost prevented, the sight is above the screen
If you crouch and crouch, you can enter Screen with Limit or not ... as high as the height
It's just right.
In the summer it is hot as it blocks the wind completely
However, in winter it is cold without Screen ...
Is Screen that can do both well?
Installation is easy
Parts I can see a lot of points, but nothing is difficult
Turner for OEMMirror (Normal Thread Screw attached under Mirror → Adapter of Opposite Thread Screw) Also attached, this is Quantity : Pair (for Left and Right) As the height is different, attention is required for that point when wearing
I did not use it because I exchange it for Mirror outside the company ...
You can install as long as 20 minutes if you do while looking at the Instruction Manual
Once you experienced with Screen, Screen was not painful and it was useless, so it was hard to have it arrived on the next day you ordered
If the longer Screen is good, it is made by Honda OEM or Endurance
As you can choose from around +2000 yen in price as well, you will like this neighborhood
The price is also reasonable and just right Length Styling and the windshield effect are personally satisfied with Large
If it's own way (173 cm and a fairly backstop) It is the feeling that the wind hits just around the center of Helmet
View detail
Fits: HONDA SUPER CUB 50 PRO, HONDA SUPER CUB110 PRO
I like Size.
Large Tiny, Small is not too much, it feels just fine.
Since it was important to look good, I purchased the rectification effect in secondary order.
Since LITTLE CUB will be nearing the Blinker part
I repeated a fine adjustment.
Although there was a statement of direct sunlight, weak vulnerability to heat,
Durability depends on the future situation.
View detail
Fits: Others 50cc-750cc for each company/Pipe handle
I am in trouble because it suits the old car
For installation it is essential that the vehicle is Pipe handle and Naked model. I think the old car is mostly Clear.
Large thing is that if there is a position changed in the position of Blinker, there is a risk of malfunctioning in the installation, so it is necessary to confirm that. There seems to be a corresponding model in the Blinker relocation.
Next is the tool, Box wrench needs 10 mm and 14 mm, and Phillips Screwdriver is required.
And in order to drill a hole in a hang cloth, a thousand- (Kiri) A hole drilling tool is required. I applied to Screen in advance with the Magic pen and marked the hole position and then drilled a hole with a sharp person attached to the Screwdriver Set.
Even people who are not good at work can do without failing first.
The installation work on the Handlebar will not fail if temporarily tightening once and then final tightening after positioning.
There is no complaints about the windproof effect during running after installation.
Helmet's Ventilation does not work because it prevents the wind too much. It may be necessary to adjust the angle at which the wind hits the head somewhat.
I think that there is no problem if it is about the legal speed + α in terms of strength.
View detail
Is it only apparent?
It looks nice but it is too small so it should not be blown away ,,,
Take Style - - - Do you take performance? - - - It's hard to do both - - -
View detail
Fits: SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125
If we do it innovation
ADDRESS V125SLIMITEDOEMKnuckle guard attaching also ... attaching ....
Commercial Mirror Adapter and 10 mm Bolt are required separately.
Gold tool upside-down and Mirror Adapter + hand held 10 mm Bolt used - L-shaped Bracket Upside-Down Replacement Screen Position Use Cap Nut to fix Mirror! For Fixing MirrorNut is used for Screen Positioning. The gap between the light case and it has become narrower.
Manufacturer also specifies this Spec. I want you to sell it.
View detail
Fits: Others 50cc-750cc for each company/Pipe handle
To KawasakiZ
I tried attaching to Z1. Quantity on Exhaust System with 4 pull out : Pair (for Left and Right) To the cloth Sauce with the same shade of Military-like Saddlebag and once in the pre-Slider-like style.
Although it is Items which makes a mistake, it is an Items which seems to be a wheelchair,.
It has the effect of the windshield, especially if it is 100 kilometers at high speed, there is no particular problem.
However, it may be difficult to attach with too low Handlebar.
View detail
Fits: Others 50cc-750cc for each company/Pipe handle
Even at MINI the effect is not MINI!
【What made you decide the purchase?】
Price that can be purchased by trial! Design remaining in Impact! It was purchased immediately with love at first sight.
【How was it actually used?】
The shield position is around the neck and there is no influence on sight. (1) 0~60km / h : Abdomen ~ chest partly prevents the wind. It might be hot without feeling the wind if it is summer. Wind blows according to the angle of the shield and wind blow near the eyes gets stronger, but the extent tolerable even without Met shield. The effect on air power due to air resistance is hardly felt. (2) 60~80km / h : Slightly wind will come in, but still firm windproof performance. Because weather at the eyes is strong, a Met Shield is necessary. The impact on power starts to appear. (3) 80~100km / h : Although wind enters truly, the difference of muddy water. It consumes considerably less physical strength. Full face is recommended as the wind to the face strengthens. Air resistance will increase and there will also be an impact on fuel economy. 100km / Even if running for one hour with h, there is no problem such as gap.
【Mounting was difficult?】
Easy with minimal tool use even by a beginner I. However, since Elimi's Handlebar was a sideways line, it interfered with instruments and Mirror. Therefore, the fixed part of the bar (Vertical Line at base) To avoid interference. In the beginning, the cloth was not used for fixing the Screw at the beginning, it was used only with the cord fixing, and it was definitely a windshield without detaching (At the time of image). On the arrangement of the Indicator, cloth was obstructed and it became invisible, so to fix it carelessly ... The troublesome one may not be Screw fixed.
【Please tell me the installation point and hang】
Easy angle adjustment and installation as long as there is no interference. Although it is natural, I think that it is better to purchase by checking the bar shape and mounting position.
[Is there anything I was disappointed about?]
Included Parts : There was a feeling that the cord of white color was torn at both ends with white color, for the time being. I think that it does not match the color of the cloth.
【Hope for Manufacturer - Please let me know if you have any improvement points]
(1) I want you to make the string above, Black at least (2) If there is a difference in the color of the cloth or the like (3) It is a rust resistant Material (Cost tough)
【Have you compared items?】
I also considered the company's Long version, but since it seemed that visibility was obstructed, I made it to this product.
[Others]
Since Elimi's Custom parts are few, it would be great if you could refer.
View detail