Reviews
lightened! but ….
I bought it to do something about the heavy Clutch on my WR250X.
The OEM has a large amount of play in the top and bottom of the lever, and the grease is easily sharp and creaks after a little while even after greasing up.
After replacing the clutch with this one, there is no extra lever play and the clutch itself is dramatically lighter at the lightest ratio position. It can be pulled even with a single finger.
The clutch switch on the OEM clutch perch could have been removed in its entirety and short-circuited, but I pulled it out of the perch and secured it with Tie Wrap in an unobstructed position, in case I wanted to return it to OEM. (Note that this method allows the Cell to turn even if you are not holding N, but the Cell will turn even if you are not holding the Clutch lever. Also note that the Switch itself, which has been removed and fixed in place, may malfunction.) 。
I considered Hydraulic Clutch, but for this Gold price, I think it is the best cost-effectiveness with good quality of parts.
The following is a regrettable part,
Quantity:It would be better to have a short lever in Replacement as it is a bit too long to operate with 2pc fingers.
The adjuster part is the same as the OEM one, but the adjuster part is not only the same as the OEM one but also has no knurl, so it is slippery and difficult to turn.
I also felt that it was a little difficult to adjust the play while driving, since the angle at which the Wire is pulled is fixed by the tightening of the Nut, so it requires quite a delicate adjustment.
Also, in the case of my wr250x, if the ratio is at the lightest position, it may not be able to pull the clutch enough, or if the clutch play increases while driving, the GEAR will be a little slow to enter. So as a result, I use the second lightest position.
Adjustments are necessary depending on the car model.
View detail
Diversion information.
I had installed SW-motech's (COBRA) hand guard on my KTM790Adventure, but the hand guard cover cracks easily even when the vehicle is tipped over almost standing up at low speed. I decided to take a countermeasure against this problem, so I installed a ZETA hand guardCover.
The reason why I chose this was because it was less than half the price of SW-motech's hand guard, and it is one of the standard hand guards for off-road motorcycles, but the most important reason was that Webig had stopped handling Repair Parts.
The actual installation is a simple task, as all that is required is to drill a hole in the aluminum bar portion of the SW-motech hand guard and cut an M6×1.0 screw thread, but the installation position is in the Quantity:Pair (for Left and Right) The setup before the work is a pain in the ass.
I am satisfied with the Large change because it seems to fit surprisingly well when installed, and now I can use various types of ZETA hand guard covers.
Now I just hope it won't break easily even if it falls down a little.
In addition, since the aluminum bar part is to be drilled and its strength will naturally be reduced, those who do the same thing should do so at their own risk.
View detail
Armour Hand Guard Bend U Clamp
It feels like I was forced to put it on, but I like the way it looks.
It is very sturdy and when it breaks, your body will be incapable of self-propulsion.
View detail
I think the texture and windproofing are both quite good
I think the quality is very good. The windproof performance is also good from the helmet down, and the speed is not so high since it is a MONKEY125, but it is quite comfortable for touring at around 60km. View detail
Fits: KAWASAKI KLX125, KAWASAKI KLX150, KAWASAKI KX250F, KAWASAKI KX450F, KAWASAKI KLX250, KAWASAKI D tracker, SUZUKI 250SB, KAWASAKI D-TRACKER-X, KAWASAKI D Tracker 125
Grip replacement was done at the same time.
Used to replace grips on klx125.
I found on the Net that it was odd to peel off the grips on the Large and that it would be better to prepare a separate Throttle tube, so I bought this one. The end can be worn in either Close or Opening, so I bought the Close one this time.
I don't have anything good to say about it, but the installation went Smooth and I have no complaints about the current situation, so I think it was not a bad purchase.
View detail
Also effective in reducing microvibration
The Normal handle bar has an integrated Bar End, but we replaced it with a Sansei RACING Handlebar, so we searched and selected a Bar End that would fit it.
Since it is made of steel, it has a certain amount of weight, and this weight has reduced the fine vibrations transmitted to the Handlebar.
Brake lever side guard is Material:Plastic, flexible, and with rounded corners, you won't have to worry about using it on the street.
Plus, if it should break, replacement parts are available at relatively low cost.
View detail
ZETA X3 Protector
I installed the AdventureArmor Handguard and purchased the Protector from the same ZETA.
Although I was not sure if I wanted to go with the XC, which is a bit larger, I was happy with the X3 because it was a small motorcycle to which I would install it.
The Size is good for those who are OK as long as they do not get hit on the fingers by flying rocks or hard insects while driving, because it is Small for wind protection.
The Master cylinder guard, removable with Screw, was also a simple but interesting GuiMick.
Four bolts are also included, making it easy to install on vehicles that already have a hand guard installed.
The color White can be Blue-ish or Green-ish. I saw a Review that said
The color of the one I received was what can only be described as White when viewed indoors or in the sun.
Perhaps there is a slight difference depending on the production lot.
View detail
Fits: KAWASAKI KX65, KAWASAKI KX85, KAWASAKI KX85-II, KAWASAKI KX125, KAWASAKI KX250, KAWASAKI KX250F, KAWASAKI KLX250, KAWASAKI D Tracker, KAWASAKI D-TRACKER-X, SUZUKI 250SB
Red purchased as a landmark.
It seems that the dirt does indeed stick to the tip of the Bolt when changing the Oil, but I'm not sure how effective it is. It just makes me feel like the dirt is sticking to me. LOL! View detail
please note
OEM Grip Heater Installation is not easy, the included bolt does not reach the handlebar weight, and even if the handlebar weight is removed, it cannot be installed with the Included Parts:. View detail
Neat around the Stem. I'm glad I bought it.
The Flasher is built into the x2Protector, and by removing the OEMBlinker, the Stem area is refreshed, making maintenance around the Stem area easier. View detail
Satisfied, except for the price.
The quality is good and satisfactory. If only the price could be kept a little lower. View detail
Fits: HONDA CR80R, HONDA CR85R, HONDA CRF250L, HONDA CRF250M, HONDA CRF250L, HONDA CRF250L/S, HONDA CRF250RALLY, HONDA CRF250RALLY, HONDA CRF250RALLY/S, HONDA CRF300L, HONDA CRF300L RALLY
perfectly normal
Bonsai after a long time because NORMAL Pedal has been rattled for Large.
The absolute strength may be high, but serration of the change shaft seems to be extra painful.
The Shift operation feel in Standing remains the same when fine adjustments have been made.
View detail
Fits: HONDA CRF1000L, HONDA CRF1100L AFRICA TWIN, HONDA CRF1100L AFRICA TWIN ADV SPORTS ES, HONDA CRF1100L AFRICA TWIN ADV SPORTS ES DCT, HONDA CRF1100L AFRICA TWIN DCT, HONDA CRF250L, HONDA CRF250L(S), HONDA CRF250M, HONDA CRF250R, HONDA CRF250RALLY, HONDA CRF250RALLY(S), HONDA CRM250AR, HONDA CT125, HONDA TRAIL125, HONDA TRX450RX, KAWASAKI D-TRACKER X, KAWASAKI VERSYS1000, KAWASAKI VERSYS1000SE, KAWASAKI VERSYS650, SUZUKI V-STORM1000
I still feel safer with the Bolt stop.
OEM Cap." Than Screw bolt." looks better. It also provides some Prank protection. I also put a Plastic bolt cap on mine.
It goes on the 2023 CRF250RLY50MD47 with no problem.
View detail
Fits: HUSQVARNA TE511, HUSQVARNA FE501, HUSQVARNA TC250, HUSQVARNA FE350, HUSQVARNA FC250, HUSQVARNA TC125, HUSQVARNA FE250, HUSQVARNA FS450, HUSQVARNA FC450, HUSQVARNA WR125, HUSQVARNA TE125, HUSQVARNA TE250, HUSQVARNA FE250, BETA X-Trainer 250, BETA RR2T 250, HUSQVARNA FE501, HUSQVARNA FE350, KTM BREMBO 125-530 XC-W 06-17, HUSQVARNA TE300, KTM 450 Rally
Nice upgrade
They will fit. They fit in the factory perches as good as the factory levers, and do fit behind the factory handguards with plenty of clearance. They are a well made product. Best levers I've ever owned. Crashed multiple times in hard pack, and soft conditions. They haven't even deformed. Will purchase for every dirtbike I own moving forward. View detail
It looks like they are all made of Titanium Alloy Gold.
The HeatProtector side has a long hole for good alignment.
It is unfortunate that Band's Screw was Minus-headed.
Material can be SUS, and a hexagonal head or Plus head is recommended.
View detail
Fits 23-year 400X
I've been trying to find out and inquire if it will fit a 23 nc56 400X.
I could not confirm it, but I was able to install it.
It seems that the brake master is different from the previous generation SingleDisc brake models.
Installation was easy.
View detail
Might be useful to have.
I think it depends on the way you fall, but in my case, when I fell standing up on a forest road, this helped me to minimize the Damage. View detail
The Front is also Titanium to match the Rear.
[How is it used?
When the rear was replaced with brembo, the mount bolt was changed to Titanium to match the look.
Was the one you received as per Image?
The real one is cooler.
Was the installation difficult?
Easy as long as Torque management is in place.
Anti-gouging agent should be applied.
How was your experience with it?
Titanium weighs 23g compared to 42g for OEM, 76g lighter for 4pcs.
I don't really know the difference, but I like the sound of Titanium.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
It would have been nice to have a VERSION without holes for Wiring.
Bolt with holes in it looks a bit Race ish.
I wanted to keep it a little more subdued.
[Points to note]
Aluminum and Titanium, so be careful of galling!
How did it compare to other products?
βMaterial:With Titaniumium's Bolt, four bottles cost almost 30,000 yen.
A Titaniumium Bolt from Zita would cost about $2500 per pc.
It costs only 10,000 yen to replace four bottles.
I am afraid to use unknown Titaniumium Bolt sold on Amazon or Yahoo!
View detail
Fits: HONDA CRF250L, HONDA CRF250M, HONDA CRF250L(S), HONDA CRF300L
Hokkaido Tour
this summer
Hokkaido Touring Schedule
Little by little, we prepare for that.
Removed for forest road touring
with ScreenKakeTamaMaju I can't mock up comfortably.
Easily removed by PointUp??
View detail
Cool
This is Cool, although I honestly don't know how effective it is.
Red is good.Color:Red is unexpectedly suitable for Gray Motorcycle.
View detail