Reviews
If you want to use only Course
When I was riding KLX230R on Course, the Rubber at the base of the Handlebar was inevitably distorted when I fell over, and the Handlebar position became wrong.
Instead of the OEM Rubber, an Aluminum conical collar is inserted and rigidly fixed so that the Handlebar will not be misaligned when tipped over.
Instead, there is no rubber, so vibration and shock will be Direct. It is a question of whether or not to replace it for touring on public roads, but it is OK if it is considered to be for course use only.
View detail
It's not just about looks.
I thought it was completely custom in appearance, but when I fell down on a forest road, it spun around and prevented me from breaking the lever.
I think it can be used in Motorcycle other than Off-vehicle as a countermeasure against lever breakage of standing fall.
View detail
Bling look
I purchased this for my 2014 Honda 450 R and took me less than 2 minutes to install...worth it and looks great.Perfect bang for the buck to provide that bling look to your bike. View detail
Z900RS CAFE.
Used to rigidize the handlebar holder of Z900RS CAFE.
The visible cracks on the handlebar holderBush became noticeable, so I decided to replace the bush, but since the Z900RS bush and the old KX250F bush are common parts, I decided to use these parts to make the bush rigid, which I have been interested in for a long time.
After the exchange, the handling is Large-Shaped Solid, and the motorcycle information is conveyed in the same way as a handlebar such as SS without Bush intervention.
On the other hand, the amplitude of the vibration is transmitted digitally to the palm of the hand, unlike Normal, which is felt as an analog waveform, so care should be taken when using Touring Main.
However, the handlebar is raised by 4mm, which makes positioning a little easier in the case of CAFE, and since it is a 2,500 yen part, it can be tried on a no-go basis, including in the event of a problem with a car that is not compatible.
However, it is not visible while driving, and when I looked at Motorcycle again after the test run, it was not as flashy as I thought it would be, and it gives the impression that some customization has been done to the handlebar. It's okay. However, if there is a ZETA Titanium color, it would be better, so I gave it a score of 4.
View detail
It's good to have a Replace product.
Isn't it often the case that the Mount part is damaged when you are attacking?
I very often fall over and get crazy with the whole Screw hole.
I have no idea what kind of force is applied to damage such a part, because I am not an expert, but I would like to know why it happens when I go to the forest road, when it does not happen when I fall down.
In some cases, the hand guard itself may be distorted.
I didn't know such a hard thing could be bent…!
I think it's very economical to be able to replace these Parts units.
As a matter of course, make sure to check the fitting before installation.
View detail
Improved rigidity
I changed Stem to ZETA, but I bought the highest size because it is said that the height of Handlebar can be changed, too. I haven't changed yet, but when I ride the small size MXMotorcycle with both kids and large people, it is very helpful to have such a product. View detail
It looks strong.
It looks solid and rigid.
For those who wear ZETA's Stem
You can select various heights to fine-tune the position of the Handlebar.
It's also handy when kids and Large people ride the same Machine.
View detail
Improved rigidity
I'm building a Stem for ZETA.
I bought it to adjust the height of the Handlebar.
The 30mm is attached to the DeFault, so I made it 55mm.
Cable seems to be NORMAL, but
I would like to add Long when it is needed.
View detail
It's nice, but the price is a little high.
I have replaced it with ZETA's Stem.
I'm wearing a 30mm Clamp.
I bought the 55mm in case I wanted a little more height.
I'm satisfied with the solid appearance, but
A little bit cheaper would be nice.
View detail
It's too expensive!
Separate handle Option Parts from ZETA, but they're too expensive!
Separate handle of XSR900 in the Spacer for Offsetting at the back I thought it was like a plate triplicate or something like that when using the ZETASeparate handle on I think
I bought this for my R25 It helps because you can do a subtle Offset, but … it's expensive …
View detail
Is it such a thing?
Purchased to attach Handlebar Guard with WR 250X attached Short Bar.
I thought that Arm was a little short but could be attached without problems.
It is nearly satisfactory, but it is more secure to install a little bit Bolt (It feels a little soft and if the installation fails, the hexagonal screw part seems to be licking and a bit uneasy)
View detail
Appearance ◎
When turning it turns and Leveretc. It reduces the breakage of ,,, but it looks like it is purchased.
Installation is OEM exchange, but it is attention because Bolt can not be used as it is because it is a Universal product.
Attached to DJEBEL 250 XC, but Mirror Clamp is short for OEMBolt, so you need to be careful as it can be tightened only 2 or 3 mountains.
I think OEMBolt will eventually replace, but with M6 the length is 25 mm. for your information
View detail
What about the performance?
The OEM is Rubber, but if it runs it will bend the Handlebar Post. Although it seems that it will be hard to bend if this product is attached, its performance is unknown because it has not been dyed yet.
It may be fashion that Red looks glaring.
View detail
Because Handlebar is Gap Le
OEM is RubberMount, Handlebar is Gap Le and rigidity feeling is not good each time it falls, so I purchased it as a countermeasure. I think that it is easy to install and securely install it.
It is still unknown what it is compared with OEM because it is not running yet.
If you leave the OEM Washer, you can not insert split Pin. I think that you can insert it by removing either the top or the bottom, but I will keep it as 4 ☆ because it is anxious.
View detail
ー ー ー ー ー ー ♪ ♪
My SEROW 250 (30 'only) Is Orange color
Because it is kimo, Orange is also included in such Small Parts
Saw!
Oh, it seems I can not choose Orange yet.
Because of rough Material, from the color of the product such as Lever
It looks a little calm. It's a nice little guy !!
When it ran "Turn around" To make it easy to avoid breakage
"Color" I'm supposed to be Mick Mick
First we do not practice ^ ^; However, it is more secure
Parts is also a pleasure of choice!
View detail
Naturally speaking it is natural! It is perfectly laughing haha
Removing ZETA 's Armor Handguard for the winter and trying to reapply it, I lost the Mounting kit
Originally Included Parts of Zeta Armor Handguard : So there is no problem mounting with the Guard! (Naturally?)
The precision of the making is also perfect, and there is nothing dissatisfied in particular. However, if the price is a little bit lower ... haha
View detail
Although the car body which is advancing the weight saving was also light, it stopped in resistance of the style, or a motor pool by Rear-box wearing, but it had fallen on the day of the typhoon.The Handle bent. It is from a Rubber portion s
Although the
car body which is advancing the weight saving was also light, it stopped in resistance of the
style, or a motor pool by Rear-box wearing, but it had fallen on the day of the
typhoon.The Handle bent. It is from a Rubber portion somehow.
Although it had bent severely, it corrects simultaneously with exchange.Since it is a product made from
Aluminum, some vibration increases, but the worries about
Handle bend should just be except lost
long distance.
View detail
Since he wanted height, it purchased. It is satisfied.
Since he wanted height, it purchased. It is satisfied. View detail
[A Webike Monitor] and a RENTHAL Renthal: Twin wall In order to carry out Handlebar wearing, since Sizes differed, the additional purchase was carried out by the attached thing.Structure is also well solid and an amateur can also attach textur
[A Webike Monitor]
and a RENTHAL Renthal: Twin wall In order to carry out Handlebar wearing, since Sizes differed, the additional purchase was carried out by the attached thing.Structure is also well solid and an amateur can also attach texture easily.
View detail
GSX-R1000 is equipped. Although it has equipped also with the billet lever, this can miss only the power thrust up from the bottom. Since there is also the way of failing to get off the ground where the power from a top is also applied actually, i
GSX-R1000 is equipped.
Although it has equipped also with the billet lever, this can miss only the power thrust up from the bottom.
Since there is also the way of failing to get off the ground where the power from a top is also applied actually, it has equipped in order to miss this power.
Since after the fall which resulted in this idea fortunately has not failed to get off the ground, a actual effect is not known, but since it leads also to improvement in a delicate weight saving and a fine sight, I attach and think that it was good.
View detail