Reviews
It looks strong.
It looks solid and rigid.
For those who wear ZETA's Stem
You can select various heights to fine-tune the position of the Handlebar.
It's also handy when kids and Large people ride the same Machine.
View detail
Improved rigidity
I'm building a Stem for ZETA.
I bought it to adjust the height of the Handlebar.
The 30mm is attached to the DeFault, so I made it 55mm.
Cable seems to be NORMAL, but
I would like to add Long when it is needed.
View detail
It's nice, but the price is a little high.
I have replaced it with ZETA's Stem.
I'm wearing a 30mm Clamp.
I bought the 55mm in case I wanted a little more height.
I'm satisfied with the solid appearance, but
A little bit cheaper would be nice.
View detail
It's too expensive!
Separate handle Option Parts from ZETA, but they're too expensive!
Separate handle of XSR900 in the Spacer for Offsetting at the back I thought it was like a plate triplicate or something like that when using the ZETASeparate handle on I think
I bought this for my R25 It helps because you can do a subtle Offset, but … it's expensive …
View detail
Increases the Universality of Mounting Parts
hand protection like the recent Cruiser and RALLY50 cars, as well as long hours of use I installed it to make Riding comfortable
When I tried to install my ZETAHand guard, I applied it to the Radial I installed it because I can't install both Brake and Clutch due to the harm of installing master
The Bar End was installed with a slight twist, which bothered me a little I put it on to avoid Harness interference and got an acceptable angle! 。
View detail
It is difficult to replace
This time, I replaced it to match the Front fork overhaul
In order to replace it, the front fork is in the way of removing the RPin and loosening the bolt If you don't remove the Front fork, it will be impossible to replace it
I also had to bend the OEM Bracket on the underside slightly to get the replacement work out
It could be as Accent
View detail
Is it such a thing?
Purchased to attach Handlebar Guard with WR 250X attached Short Bar.
I thought that Arm was a little short but could be attached without problems.
It is nearly satisfactory, but it is more secure to install a little bit Bolt (It feels a little soft and if the installation fails, the hexagonal screw part seems to be licking and a bit uneasy)
View detail
Sorry a little
There was a big bubble in the Sponge part. I'm sorry. I think that it is obviously a defective product. I installed it so that bubbles can not be seen. The feeling is good.. Examination etc. I thought that I would like you to be more polite. View detail
I think that it is easy to use
In the case of klx125, since Handlebar struggles to adjust and reposit many times to bend from the Rubber part from the attachment part due to overturning, we purchased it to solve with this product, but due to our convenience Not installed - - According to the attached review, vibration is transmitted to Handlebar as brittle - - - I am planning to write it again after installation - - - I think that it is personally good. View detail
With Impact
Since it was good except for installation on DJEBEL, it is also mounted on RMX. Next time I bought DRC's ColorBolt together.
I am concerned about fading because the color is Red. Besides ZETA 's Red fades quickly but Red can not be helped.
Since some of Mounting Bolt is offset, it can not be used, so I wish to release it even if it is offset difference.
View detail
Appearance ◎
When turning it turns and Leveretc. It reduces the breakage of ,,, but it looks like it is purchased.
Installation is OEM exchange, but it is attention because Bolt can not be used as it is because it is a Universal product.
Attached to DJEBEL 250 XC, but Mirror Clamp is short for OEMBolt, so you need to be careful as it can be tightened only 2 or 3 mountains.
I think OEMBolt will eventually replace, but with M6 the length is 25 mm. for your information
View detail
What about the performance?
The OEM is Rubber, but if it runs it will bend the Handlebar Post. Although it seems that it will be hard to bend if this product is attached, its performance is unknown because it has not been dyed yet.
It may be fashion that Red looks glaring.
View detail
Because Handlebar is Gap Le
OEM is RubberMount, Handlebar is Gap Le and rigidity feeling is not good each time it falls, so I purchased it as a countermeasure. I think that it is easy to install and securely install it.
It is still unknown what it is compared with OEM because it is not running yet.
If you leave the OEM Washer, you can not insert split Pin. I think that you can insert it by removing either the top or the bottom, but I will keep it as 4 ☆ because it is anxious.
View detail
ー ー ー ー ー ー ♪ ♪
My SEROW 250 (30 'only) Is Orange color
Because it is kimo, Orange is also included in such Small Parts
Saw!
Oh, it seems I can not choose Orange yet.
Because of rough Material, from the color of the product such as Lever
It looks a little calm. It's a nice little guy !!
When it ran "Turn around" To make it easy to avoid breakage
"Color" I'm supposed to be Mick Mick
First we do not practice ^ ^; However, it is more secure
Parts is also a pleasure of choice!
View detail
ZETA Rubber killer
I bought ZE37-0321Red for KLX 125.
Since KLX 125 is a Rubber mount and it has a Bar rise kit 30 mm, it gets twisted merely by lightly mossing, so I installed it.
I did not twist easily as I intended.
Direct feeling also comes out and I do not mind the vibration.
KLX 125 could not be installed on the bottom unless you take the Top Bridge.
View detail
Purchased for FAT-Bar
Purchase later purchase hand guard's installation size since it was Size for Normal handle.
It is very nice that the Parts necessary for this Parts can be purchased partly.
Even when it gets broken, you only need to purchase Parts and it will be available for a long time.
View detail
Exchange around Handlebar
Handlebar Clamp bent and it felt strange to Handling, so I bought it along with the exchange around Handlebar.
It is exchanging only at the upper part, but I like Snap and Handling and I like it. I do not mind being so much concerned because I got together with the Pro grip. Anodized Red is one point and the Custom feeling has improved sharply. It changed to DRC's Short lever, so it looks better also Parenthesis better.
View detail
Naturally speaking it is natural! It is perfectly laughing haha
Removing ZETA 's Armor Handguard for the winter and trying to reapply it, I lost the Mounting kit
Originally Included Parts of Zeta Armor Handguard : So there is no problem mounting with the Guard! (Naturally?)
The precision of the making is also perfect, and there is nothing dissatisfied in particular. However, if the price is a little bit lower ... haha
View detail
I had PROTEPER SE bar handle Carmichaerl model and a bend type hand guard. This combination of standard size still installable. However, if I adjust to my best position, the master cylinder bolt interferes. I was not happy about the position and have been
I had PROTEPER SE bar handle Carmichaerl model and a bend type hand guard. This combination of standard size still installable. However, if I adjust to my best position, the master cylinder bolt interferes. I was not happy about the position and have been patient to use for a while, but enough! I decided to get new one. The installation is easy just exchange the mounting. However, the hand guard need to be modified a bit to make the installation easier.
Its curve need to be more opened. Of course it can't be done by hands, so I used a street ditch to bend it.
I put the hand guard and some protector cloths into the ditch hole then push-push. Actual change is not much, but it creates enough clearance to the extended portion.
I am more than satisfied! Finally I can ride with my best position. In addition I changed the clutch side too although it didn't have problems with standard size.
View detail
This bar clamp is awesome. It wards off the impact you get when you fall and rotate.I fell two times to the left and three times to the right, but thanks to this bar clamp, my motorcycle hasn't been seriously damaged nor distorted.Normally it does
This bar clamp is awesome. It wards off the impact you get when you fall and rotate.
I fell two times to the left and three times to the right, but thanks to this bar clamp, my motorcycle hasn't been seriously damaged nor distorted.
Normally it doesn't move even if you press it hard, but it rotates when it comes under great pressure.
You need to be careful not to overtighten the bolt when installing, but it's not that difficult. (I'm using a DRC aluminum bolt, the one shown in the picture.)
The surface finishing of this red anodized aluminum rotating bar clamp has a high-class feeling and beautiful.
It is a customizing item that serves not only as an decoration but also as a protection part which rotates in case of falling. It's worth buying.
I am using this bar clamp for my right handle.
There's another product for the left: ZETA Rotating Bar Clamp (with Mirror Hole: ZE40-9412).
It isn't that expensive. If you don't have one, you might regret in case you fall and damage your lever. It will serve as an insurance against accidents.
This ZETA product has beautiful anodized finishing, and unlike ones of other brands it restores its color better. It is a reliable product.
I will post five stars (full score) for this bar clamp without any question.
It is great, for it can be a practical insurance as well as a stylish decoration. It is easy to install and above all, it has comparatively reasonable price!
View detail