Reviews
Also effective in reducing microvibration
The Normal handle bar has an integrated Bar End, but we replaced it with a Sansei RACING Handlebar, so we searched and selected a Bar End that would fit it.
Since it is made of steel, it has a certain amount of weight, and this weight has reduced the fine vibrations transmitted to the Handlebar.
Brake lever side guard is Material:Plastic, flexible, and with rounded corners, you won't have to worry about using it on the street.
Plus, if it should break, replacement parts are available at relatively low cost.
View detail
Large satisfaction, I should have changed it earlier.
I have tried various levers from brembo OEM, but this one fits me the best, including one for Clutch SideRCS.
When I inquired about the compatibility with my favorite XR0.11.71, I was told that it was not made by brembo, so I could not get an answer. I checked the description of ASite and found that RMCMASTER is available! I immediately bought it because the delivery date was earlier than this one.
View detail
ZETA X3 Protector
I installed the AdventureArmor Handguard and purchased the Protector from the same ZETA.
Although I was not sure if I wanted to go with the XC, which is a bit larger, I was happy with the X3 because it was a small motorcycle to which I would install it.
The Size is good for those who are OK as long as they do not get hit on the fingers by flying rocks or hard insects while driving, because it is Small for wind protection.
The Master cylinder guard, removable with Screw, was also a simple but interesting GuiMick.
Four bolts are also included, making it easy to install on vehicles that already have a hand guard installed.
The color White can be Blue-ish or Green-ish. I saw a Review that said
The color of the one I received was what can only be described as White when viewed indoors or in the sun.
Perhaps there is a slight difference depending on the production lot.
View detail
Fits: HONDA CRF1000L Africa Twin, HONDA CRF250 RALLY, HONDA CRF250L, HONDA CRF250M
You can open end with ease.
I bought it to attach a Closed type hand guard.
I was worried when I bought it because I read in other reviews that the total length was too short, but Large seemed to be sturdy.
When installed, the distance from the end of the handlebar to the end of the throttle tube is about 7mm inward. 120mm PROGRIP grips were installed, and they protrude a little from the throttle tube.
Although there is a gap from the edge of the handlebar, I thought it was a safe design with sufficient clearance considering that a hand guard is attached.
If Bar End is attached, gaps may be a concern.
View detail
Interference with clutch lever
[How is it used?
Daily use such as commuting
Was the one you received as per Image?
Not on Image Street.
Was the installation difficult?
Difficult.
How was your experience with it?
Grip slips.
[Included Parts:were they on?
Already included.
[Was there anything that disappointed you?
It was mentioned that the Small diameter was used to reduce interference with Lever,
Interference was found. close to the Switch box up to Limit,
I used a curved Clutch lever and it interfered with the Flange.
Flange diameter of this product:Φ57mm
OEM Product Flange Diameter:Φ44mm (measured with Caliper)
This will cause interference.
View detail
please note
OEM Grip Heater Installation is not easy, the included bolt does not reach the handlebar weight, and even if the handlebar weight is removed, it cannot be installed with the Included Parts:. View detail
Neat around the Stem. I'm glad I bought it.
The Flasher is built into the x2Protector, and by removing the OEMBlinker, the Stem area is refreshed, making maintenance around the Stem area easier. View detail
zeta bar rise kit
I love the fast delivery. I also praise the meticulous packaging. It's before installation, but I feel that the product is in very good condition. It's not comparable to the one made in Chi** View detail
Fits: HUSQVARNA TE511, HUSQVARNA FE501, HUSQVARNA TC250, HUSQVARNA FE350, HUSQVARNA FC250, HUSQVARNA TC125, HUSQVARNA FE250, HUSQVARNA FS450, HUSQVARNA FC450, HUSQVARNA WR125, HUSQVARNA TE125, HUSQVARNA TE250, HUSQVARNA FE250, BETA X-Trainer 250, BETA RR2T 250, HUSQVARNA FE501, HUSQVARNA FE350, KTM BREMBO 125-530 XC-W 06-17, HUSQVARNA TE300, KTM 450 Rally
Nice upgrade
They will fit. They fit in the factory perches as good as the factory levers, and do fit behind the factory handguards with plenty of clearance. They are a well made product. Best levers I've ever owned. Crashed multiple times in hard pack, and soft conditions. They haven't even deformed. Will purchase for every dirtbike I own moving forward. View detail
Change from M6Type
I had fixed SONICHand guard on my M6Type, but the bar end weight of Kawasaki car is only fixed to the inside of the bar by rubber, so it was stress that the hand guard gapped due to vibration when riding. I took the opportunity of replacing the OEM handlebar and purchased this one and installed the hand guard. I am satisfied that the hand guard is firmly fixed and does not shake when mounted. Two types of attachments are included to match the inside diameter of the bar. In addition, the HandCard can be fixed in or out of two positions.
It is very solidly built, but therefore quite pricey.
View detail
Universality is strict
If the car model is not sold with a dedicated kit, the installation adjustment is Large strange.
I installed it on SUPER SHERPA, but cut and Screwed and bent,
We finally arrived and are not satisfied.
If you do not mind a gap at the Handlebar End, you can put it on without modification.
View detail
Changed from a fixed system to inner weight when handlebar was replaced.
The STD Handlebar uses a type that is fixed to the Inner Weight at both ends of the bar, but the Weight itself is only fixed by the Rubber, eliminating the Stress that causes the Guard to move due to vibration while riding. View detail
Fits 23-year 400X
I've been trying to find out and inquire if it will fit a 23 nc56 400X.
I could not confirm it, but I was able to install it.
It seems that the brake master is different from the previous generation SingleDisc brake models.
Installation was easy.
View detail
Fits: HONDA CRF250L, HONDA CRF250M, KAWASAKI D Tracker, KAWASAKI KLX250, SUZUKI DR-Z400S, SUZUKI DR-Z400SM, Others
Sporty TRAILHandlebar
Mounted on SEROW225. I used to use a Narrow Handlebar to attack the woods, but it was difficult to control and the form did not look good. The SEROW225 has less of the SEROW's "TRIAL" feel, but it is still great for situations such as Black Cannon and Motocross courses where you are standing still and driving at relatively high speeds. The texture is good, and the color is also very appealing, so I would like to repeat this every time I bend it in the future. View detail
Fits: YAMAHA DT230LANZA, YAMAHA TW200, YAMAHA TW225, YAMAHA TRICKER, YAMAHA XT250X, YAMAHA XT250, YAMAHA TTR250, YAMAHA SEROW250, YAMAHA SEROW225, YAMAHA WR250X, YAMAHA WR250R
Turning blue
The short lever of the RALLY50 I have been using since the XG250 TRICKER rattled, so I decided to go out on a limb and replace it with this one.
You can see it shining Blue when you get on it, but you can't see it from the front because of the hand guard.
I don't think there is any difference in operability between the Short lever and the Large lever I was using before, but the range of adjustment is increased.
The OEM rubber cover cannot be installed as is and requires modification.
I kind of cut along the Bellows and it looks like the picture.
View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250F, YAMAHA YZ250X, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ426F, YAMAHA YZ450F, YAMAHA YZ80, YAMAHA YZ85
It may be a classic.
I bought this one because a certain lever that does not break interferes with the CloseHand guard on a 4Finger. If you care about the appearance, you should choose the cut-out type, but if you don't want it to break during the race, you should choose the Forged Type.
The exterior is of high quality, as one would expect from Zita. Installation is a simple and easy process. Adjustment is stepless, but requires a tool, so it is a little troublesome.
I have fallen a few times since installation and have not had any breakage or other troubles.
View detail
Tightens up the look.
Was the one you received as per Image?
It was something I saw often, so it's on Image.
Was the installation difficult?
I used a hand guard from the same Manufacturer, so no problem at all!
How was your experience with it?
I don't know if it is useful yet because I haven't driven it in a place where it would be useful, but it looks very atmospheric and satisfies my sense of ownership.
[Included Parts:were they on?
Installation Bolt
[Was there anything that disappointed you?
None
Other items that would be helpful
Of course, the same Manufacturer's hand guard is only a few minutes' work!
View detail
Might be useful to have.
I think it depends on the way you fall, but in my case, when I fell standing up on a forest road, this helped me to minimize the Damage. View detail
the handlebar is highlighted
Repurchase due to size miss It's perfect for giving points to the zeta handlebar. I recommend buying it because it's cheap. View detail
Easy to install, cost-effective, good-looking
This XCProtector is installed on a CRF150L with ZETAArmor HandguardBent.
The time required is about 2 to 3 minutes since it only stops two Screws on each One Side.
It looks LARGE and better as shown in the photo.
Cost-effective and great.
View detail