Reviews
Universality is strict
If the car model is not sold with a dedicated kit, the installation adjustment is Large strange.
I installed it on SUPER SHERPA, but cut and Screwed and bent,
We finally arrived and are not satisfied.
If you do not mind a gap at the Handlebar End, you can put it on without modification.
View detail
Fits: HUSQVARNA FC250, HUSQVARNA FE250, GASGAS MC250, HUSQVARNA FX450, GASGAS MC125, KTM 250XC-F, KTM 300XC TPI, KTM 250XC-W TPI, KTM 250XC-W, KTM 200XC-W, KTM 150XC-W/TPI, KTM 350XC-F, KTM 125XC-W, KTM 250XCF-W, KTM 300XC-W, KTM 300XC-W TPI, HUSQVARNA TC250, HUSQVARNA TC125, KTM 500XCF-W, KTM 350XCF-W
Improved Brake grip comfort
I installed it on my gasgas EC250 which I always use for forest road touring.
The OEM Brake lever did not give me a good supplemental grip, so I bought this lever to try it out.
Fit feeling of the fingers is good, and the feel when operating the Lever is very much improved.
Furthermore, the fact that the lever is foldable makes it difficult to break, which is good, and reduces the number of troubles during touring on forest roads.
The quality is good and I like the Large change.
The only drawback is that the price is very high.
View detail
cheap
Usually! They say it's suitable for Doorknob grip, but it doesn't compensate for anything, it just doesn't have any slippage in extra places.
Just cheap. In this day and age when Kishida is undermining OWallet, the price is quite helpful and that's all that matters.
Fatigue, whatever it is, I don't grip anyway, that's all.
View detail
I need a 2Finger.
The truth is that Quantity:I prefer 2pc seating, but only 3Finger is available, so I bought it.
It is about 2cmShort, but I don't feel much change.
When I tried to install it, it was not good enough, so I went back to 4Finger.
View detail
Fits: HONDA CRF250L, HONDA CRF250L(S), HONDA CRF250M, HONDA CRF250RALLY, HONDA CRF250RALLY(S)
Purchased to change the front/rear position of the handlebar.
I bought this to move Handlebar forward.
The description of the product says that it is the largest 8-position, but this product has only one hole in the base, so it is a 4-position.
As a result, I was a little disappointed that it did not move forward as much as I expected.
CRF250RALLY had a problem that when standing on a hard slope, it would be in a position like hanging from a handlebar, and the arms would be cramped.
I was aiming to increase the degree of freedom of the upper body by moving the handlebar, which is shallow and low, forward together with this clamp kit, but it did not work as I had hoped.
However, I have no regrets because of the difference from OEM.
The bolt that holds the key cylinder in place is a special one that can only be turned in the direction of tightening, so it was necessary to make a hole in the bolt and remove it with an extractor. 。
This work is not recommended for those who are not accustomed to using electric drills and the like.
View detail
Fits: YAMAHA MT-07, YAMAHA XSR700, YAMAHA XSR900, KAWASAKI Z250, KAWASAKI Z400, KAWASAKI Z1000, YAMAHA MT-09
I was able to install it on my '22 MT-07 with no problems.
Installation completed on a '22 MT-07.
An 8mm hexagonal Wrench is needed to remove the Bar End of the M16Type.
I think it would be effective for Bar End protection and insect attack while driving.
View detail
Maybe it's a little bit messy!
It is a little cheap and there are some details that are a little clunky, but since it can be replaced quickly, I'm satisfied that this is what it is. It might be better to check it at a real store before purchasing. View detail
I used it for a Handlebar with a thick inner diameter.
I installed it on a HUSQVARNA TE2502017 which I always use for forest road Touring.
When I changed the handlebar to an ISA one, the inner diameter of the handlebar became thicker and the handlebar guard I had been using could no longer be used. I purchased this Adapter and was able to fix the bar end without any problems.
View detail
Installed during handlebar replacement
I installed it on my HUSQVARNA TE250 2017 which I always use for forest road Touring.
This Bar End can be used for both large and small inner diameters by changing the Adapter.
I didn't like the Bar End that popped out so much, so this thin Bar End was very Balanced and just right.
View detail
A little different from my taste.
It's thin, so it's hard, but it's hard. And it hurts. View detail
If you prioritize performance, you can't let go in the middle of winter.
After the age of 60, the cold became unbearable.
Grip warmer + Handlebar Cover will keep your hands warm and toasty.
Those who wish to ride off-road motorcycles between December and February are encouraged to consider this option.
View detail
It would be different if there were.
Since it is installed on an on-road vehicle, the position of the vehicle may have something to do with the wind, but it is not as windproof as the AdventureMODEL, but considering that I will be using the Grip heater in the future, I wanted to prevent direct wind even a little, so I installed it and adjusted the installation angle to prevent wind at high speeds. So, I used a thin rope to lift it up and prevent deformation with the Handlebar Guard. View detail
Cannot be fixed as per Manufacturer's note.
I bought it knowing that it is not compatible with CB650R, and I could install it by transplanting a crescent shaped Spacer from another product which is compatible with CB, but it was impossible to fix and guard it at any position because the bar rotates with STD Handlebar. I know it's not so good to use it with Knuckle guard, so I put a strong and thin rope through the bar and use Mirror Bracket as a fulcrum to lift and fix the bar with a string. (Self-directed) The product itself is mostly plastic, so it is not very strong, and the paint easily peels off when installing or reassembling the Gold attribute parts. View detail
Mounted on JA65
The Accelerator Wire is caught in the Guard when operating the Handlebar, and the optional Scud Protector also interferes with the Blinker. I have given up and use it with the interference.
The Squid Protector is originally designed to be flipped upside down, but it is not supposed to be flipped because of stiff interference.
View detail
ZETABar pad
White is changed to Black because it turns yellowish in sunlight. View detail
Simple and GOOD
Installation on Taper Handlebar requires a little hang.
The Fixing Screw must be tightened in an ingenious way to ensure successful installation.
Once installed, the Guard effect is perfect in the event of a fall.
I like it because the structure is Simple.
View detail
I'm glad we have Replace, though.
Enduro racer (YZ125X) Used in.
I'm glad to be able to replace the right side of the screen because it breaks down frequently, but I wonder if it is a habit of mine to break only the Right side, and there are several Lefts left over.
Quantity:Pair (for Left and Right) I would be more than happy if it were sold separately, so I hope to see improvements.
View detail
Good construction, but questionable shape
After installation, the handlebar moves forward about 1 cm.
This makes it easier to ride, but the handlebar operation becomes slower.
The product has a martial construction, but it feels good to the touch and is not of bad quality.
In the case of 28 cm, the bottom of the product has a slightly convex shape instead of the 28 cm semicircle.
Is it to fit some kind of car model? Maybe it is.
This creates a cavity in the Mount and this product's mounting area, which is both unsightly and puddles in the rain.
If you take appearance into account, it is a good product.
View detail
It is a classic.
It is a consumable item, but the Material is hard and breaks easily.
Quantity because the shape is good.:This is my 2nd Set and I wish it was a little more flexible.
View detail
Fits: SUZUKI GSX-R1000, YAMAHA FZ-1, YAMAHA FZ-1 FAZER, YAMAHA XJ6N, YAMAHA YZF-R1S, YAMAHA YZF-R1M, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R7, YAMAHA YZF-R6, YAMAHA YZF-R6, SUZUKI GSX-R600, YAMAHA FZ-07, YAMAHA MT-07, YAMAHA FZ-09, YAMAHA MT-09, YAMAHA MT-09SP, SUZUKI GSX-R750, SUZUKI GSX-R1000R
SP is not available
I have no complaints about the PARTS used by YOSHIMURA,
Installation is not particularly difficult. However, when I tried to install it, I found that the separate parts to hold the SafetySwitch installed on the lever hit the Holder! (In reality, only half of the money is seized) Why? Why? I inquired and found that sp is not available for installation!
I was able to get separate parts for the PilotLever and installed them. When I bought the car, I think that they do not distinguish between the sp and normal models, although they do give the year of the car. If you are going to purchase a car, please be careful! I have no complaints about the product itself.
View detail