Reviews
It's solid
Up to now, I had applied MDF Lime green and 10mm rim stripe on the wheel painted black, but now I have replaced the rear wheel with a ZRX1200R one, so I purchased the same MDF rim stripe and reapplied it on the front.
I thought that if I was going to replace it, I would use Makeover, so this time I decided to use a thinner one, 6mm and 4mm, and I thought the thickness should be 6mm and the color should be different, but in the end, I chose 6mm Lime green as the same color because the other colors did not feel right to me at all. I chose the same color, Lime green, 6mm.
First of all, after removing the Tape that had been attached, I felt that the Rim stripe on the MDF is a no-mistake thing. The MDF rim stripe is very firmly attached to the tape. It is not difficult to peel off, in fact, it was easy to peel off without breaking off in the middle, but unless you try to peel it off intentionally or accidentally, it does not seem to come off naturally. For a cheap rim stripe review, see It's peeling off." etc., but this does not seem to be the case with this Rim stripe.
As for the application process, I believe it can be done with the wheel attached to the car body, but I did the work with the Timing with the Wheel removed. I did the work with the Timing wheel removed. I cut out the backing paper for each tape, degreased the rim of the Wheel, sprayed water lightly on the rim with a mist, and started pasting. When pasting, hold the tape so that the Start position does not move, and trace the tape with the belly of the finger of the opposite hand so that the water drains from the adhesive surface. Finally, warm the Tape with a dryer to make it adhere to the Rim. If you pull too much when applying the tape, the finished circle will be rattled and the adhesion of the sticking part may be weakened, so be sure to adjust your strength. However, the thinner the tape becomes, the more easily it is affected when it is pulled. Also, the overlapping area should be even etc., and since there will be a gap between the tape and the rim above the overlapping area, it is important to warm the tape firmly so that it adheres to the rim. The finished product was generally as I had imagined, and I think it would have been white even if I had made it 4mm.
View detail
Attached to Ducati SCRAMBLER
I bought this to attach Rim stripe to my newly purchased DucatiSCRAMBLER.
Size is 17&18-inches Color to match the car body color:YellowSingle Body 10mm width was chosen.
I wanted to start pasting immediately, but I don't know which wheel to paste the 18 separate tapes on.
There is no mention of this in the Instruction Manual.
Are the top 8 sheets in the front FOR 18-inches or FOR 17-inches?
Are the two spare sheets the last two on the front or the back?
Are you asking me to paste it in the right way?
As a matter of urgency, I inquired through MDF's Home page.
I have not received a reply yet so I am unable to paste it.
View detail
Name Chain
Since it is a black wheel, it was installed together with Tire's WhiteLetter as one point of reference.
Degrease and apply the paste with soapy water, being careful not to stretch the paste by pulling it.
Maybe it would have been easier with a special tool. I don't know.
Tire is much easier to work with if it is free to turn.
View detail
WheelBlack with YOSHIMURARedLogo is a nice touch.
I put it on the rim of my GSX1300R HAYABUSA (EJ11A) and I am satisfied with the YOSHIMURA with Logo and I think it looks good underfoot. View detail
It's a quick and easy way to give a new impression!
MDFRim stripe affixed using Gauge.
If you are going to paste without using Gauge, you will need to apply it carefully with water, but if you use Gauge, you can apply it beautifully without using water.
You can easily change the look and feel of the original Motorcycle and feel a sense of self-satisfaction!
View detail
Rim sticker
Easy to put up.
It sticks well.
Quite sturdy.
View detail
Fits: Others 17Inch wheel car
Worst product
[How is it used?
Introduced to add One pointAccent to Wheel in one color Black.
Was the one you received as per Image?
It was a SilverPlating Film-like Tape.
Was the installation difficult?
When I removed the Wheel from the car body to replace the front and rear tires, I attached the Sticker by the way. After washing the wheel with neutral detergent, I moistened the wheel rim and Sticker with water using a spray mist, and carefully applied the Sticker using Squeegee. I bought a Sticker for a 17-inch wheel, but the curvature of the Sticker did not match the curvature of the Wheel, so I warmed it up with a dryer while adjusting it to the curvature of the Wheel, and managed to attach it. It took me at least an hour to stick one side of the Wheel.
How was your experience with it?
The day after I put it on, it was already peeling off (crying).
Since FilmTape has almost no flexibility, it softens and conforms to the curvature of the Wheel only when heated in a dryer, but it returns to its original shape when cooled, so it will naturally peel off. The adhesive is not that strong. I tried to warm up the peeled part with Dryer and reapply it, but it was peeled off the day after Paris, so I peeled off all of them and threw them away because I was disgusted and felt that further measures were a waste of time!
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Worst product ever!
Other items that would be helpful
Opinions and requests to Manufacturer
It is a scam Manufacturer to sell such an inferior product!
View detail
In Black wheel's Accent.
The black painted wheels looked too heavy, so we introduced rim stripe.
I was confused with Titaniumium color for a long time, but the one that goes better with my ZEPHYR color is
I figured it would be the Blue one from Delicorol, so here it is. 。
This may be due to the fact that I did not use RimGauge when pasting.
If the overlapping dimension of the connection part is about 10mm, the last overlapping part overlaps by about 30mm.
I reposted it. 。 Maybe without RimGauge it would unintentionally pull and stretch when pasting?
The color overlap part here is the "Colored" part, so the above problem will not be so much of a problem if you make the spec. overlap in the "Black" part....
View detail
To prevent slipping
Previously used Rim Band.
If you wear them without air, the Tube will sag or Gap.
However, if you use rim tape, the Wheel side is a tape stop, so it is less slippery and much more effective than Band.
View detail
Fits: YAMAHA V-MAX 1680, YAMAHA XG250 TRICKER, YAMAHA V-MAX 1680, YAMAHA SEROW250, YAMAHA MT-01, YAMAHA V-MAX 1680, YAMAHA MT-01, YAMAHA MT-01, YAMAHA MT-01, YAMAHA MT-01, YAMAHA MT-01, YAMAHA MT-01, YAMAHA MT-01, YAMAHA FJR1300AS, YAMAHA FJR1300A
So easy, so beautifully put up!
I put it on a 16-inch rear wheel and a 19-inches front wheel, but it did not become wrinkle, and it was relatively easy to put on wheels of different sizes.
Adhesion is firm and durability seems to be fine.
View detail
One point on your feet.
Purchased Black6mm.
I bought it as a One point kind of thing, but I think it could have been a little thicker.
The workability was good, and since we purchased the special Gauge, installation was easy.
It would be troublesome without a dedicated Gauge. (Quantity):(Set should be sold)
I am satisfied with the product.
View detail
Stylish MONKEY125 undercarriage.
The color of the goros and design is good. I was using a cheap one (880 yen), but it is different from a large one. I am sure there will be no problem with the durability of the product since it is made by YOSHIMURA. I found a video of the process of stretching the wheel by ManufacturerYOSHIMURA, which helped me a lot. View detail
OEMWheel's Easy Makeover
The texture of Sticker is very good like YOSHIMURA.
If it is a general wheel rim shape, Sticker's design can be applied beautifully without gapping, and if it is applied with water, it can be easily corrected, so it can be applied beautifully even for the first time.
View detail
MONKEY125's undercarriage is GU.
When I was looking for a rim sticker for MONKEY125 at Webig, I found ManufacturerYOSHIMURA's product. The design and texture of ManufacturerYOSHIMURA's with Logo is superb, and since I am currently using Red color Rim sticker (880 yen at Amazon.com), the appearance is not as good as it looks. It is expensive, but it matches MONKEY125 (Red color) effectively, and it is massive and tasteful. The video of how to apply the sticker is available at ManufacturerYOSHIMURA. View detail
Finally, it's sticking!
I switched to GSX and first bought MDF Rim stripeM6 Red.
As per Instruction Manual and You Tube videos
Degrease firmly.
Spray lightly with a mist of diluted neutral detergent.
Paste while removing air using a special Guide.
In the end, when I tried to paste it after moistening it with a misting spray, the sticking was weak. Is this Large sturdy? The work was completed with the thought.
After drying thoroughly, it was peeled off and gone after a few miles of driving.
Next, purchase Rim stripeM6Tricolor.
Paste in the same work process.
However, as before Spray with a mild detergent solution. The sticking was weak at the "1" point, and I thought it might come off again, so I dried and aired it out with Dryer to complete the work.
As a result, it was still peeling and pelePera, although it did not disappear after a few kilometers.
I bought the light gray this time for the third time.
This time, we dared to paste directly after perfect degreasing without using a neutral detergent solution.
As a result, there is no sign of peeling.
Finally, I can run with peace of mind.
Has the quality of the glue gone down?
Is there a problem with Wheel in gsx?
I don't know. I don't know. Neutral detergent solution." will not be used from now on.
View detail
Reupholstered MDF Rim stripe
I replaced it with Titanium, my personal favorite Rim sticker.
The original wheel has a Vinyl type rim sticker, and it can be removed by using Remover.
It took some time to peel off and wipe up to remove the glue, but all the areas were reupholstered.
As with the last GSR400, I still love the look!
I would like to replace the wheel in the near future because the current wheel has some rust in it.
In the meantime, if you like the way it looks, you will want to ride a motorcycle! We believe that this is directly related to the following
I am personally satisfied.
View detail
It corrects, although it described that the wrinkle was in play contained last time. When 24 hours or more passed, the wrinkle had disappeared. It is in play at the time of 12-hour progress last time.
It corrects, although it described that the wrinkle was in play contained last time.
When 24 hours or more passed, the wrinkle had disappeared.
It is in play at the time of 12-hour progress last time.
View detail
It purchased for appearance. A result is large satisfaction. Since he liked black and blue, the thing of the blue character was chosen as the black material, but since the area of a black material occupied mostly, it was thought that it was not un
It purchased for appearance.
A result is large satisfaction.
Since he liked black and blue, the thing of the blue character was chosen as the black material, but since the area of a black material occupied mostly, it was thought that it was not unexpectedly conspicuous.
(Natural although there are differences of enough if compared with normal ..) Although it thinks that the angle which takes a photograph is also a problem, the impression which is seen rapidly and received is the touch which says that the edge of the tire spread inside.
If appearance was thought more as important, possibly the monochromatic blue product should have been chosen.
Anyway, since it is satisfied with the product itself, I purchase and think that it was good.
However, since this stripe has become comparatively for 4 minutes, the point worried one sticks it, as the portion of a joint overlaps for a while.
(It seems that it is the measure which considered the hit in case of the size of exactly since it is hard to stick by it) If it sticks in the pile and the crevice between joint parts is not processed exactly, garbage will enter from the crevice and it will become a cause of peeling.
Those who are worried will think whether it is satisfactory, if the portion of a joint is cut.
Since I was troublesome, I stuck in piles as it is as the description.
If this point and an edge are separating, I think that it will cut then.
View detail
In the silver color, since a tire size was also small and the wheel lacked in force, it equipped. The difficulty of the wearing [ itself ] was OK with the feeling which sticks a sticker highly. Since the decal itself has thickness, there are also
In the silver color, since a tire size was also small and the wheel lacked in force, it equipped.
The difficulty of the wearing [ itself ] was OK with the feeling which sticks a sticker highly.
Since the decal itself has thickness, there are also few fears of air bubbles and a wrinkle entering, and if even an attachment location takes care, it can complete finely.
If a front wheel is equipped, does it become a style with a piece?
Although the engine performance of a motorcycle is not raised, I think that it is a high product of the dress-up effect up.
View detail
AGUSTA
I have been satisfied with the product for quite some time now with no peeling. View detail