Reviews
Purchased for pasting Graphic in Race
The OEM exterior is kept for when the vehicle is sold and an external exterior is used.
It is a little thinner than OEM, but I have been riding it every week for more than a year for practice in Race and it is very cost effective.
It went on easily without any gap in the hole position.
(It was common for external exteriors from a long time ago to have holes that did not match.)
It is a very good product because it is Reasonable and can replace the entire exterior.
View detail
BABYFACERacing hook installation
Installed for use as a loading hook.
Installation can be done by simply removing the Tandem FootpegBracket.
Left Side is to use KIJIMA's Helmet holder.
The Helmet Holder Bracket is inserted under the provided Aluminum Collar, and then the Racing Hook is installed under the Aluminum Collar.
Even so, the HolderBracket and the Racing hookBody still interfere slightly, so the HolderBracket was shaved a little and installed.
In addition, the Left SideMounting Bolt was changed from the supplied 30mm to a 35mm due to the Helmet holder being sandwiched between the two.
View detail
I think the texture and windproofing are both quite good
I think the quality is very good. The windproof performance is also good from the helmet down, and the speed is not so high since it is a MONKEY125, but it is quite comfortable for touring at around 60km. View detail
Fits: SUZUKI GSXR1300R HAYABUSA
To make the long haul a little easier.
Would it be easier to have it?
I had never put this kind of thing on before for personal appearance reasons, but I think it would have been easier if I had.
In case of GSX1300R HAYABUSA, I am a little disappointed that there are not many places to touch when I put it on the Limit under the Tank when I do the Knee grip.
It took me quite a while to think that I just had to put it on.
Of course, the more time it takes, the more beautifully it will be applied so that no air will be trapped.
View detail
A little bit
It looks slightly better.
I think the choice of GROM letter color is a bit of a Large thing.
View detail
Fits: KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
Looks practical.
We lost the NORMAL Hook when we converted to Fender Eliminator.
Purchased. It is a little smaller, but it seems to be stronger.
Looks fine with touring bag attached.
View detail
Ideal for preventing damage to Number….
I noticed that the reverse side of the License Plate was getting dirty with mud and Asphalt-like substances, so I purchased this plate for two purposes:to prevent dirt from staining the plate, and to prevent damage to the License Plate since it was almost bent when the Number was caught a few times.
After installation, it is completely hidden by the License Plate, so it is not visible from the rear, but the reverse side is protected and serves as a reinforcement for the License Plate, which may be useful for Large to prevent damage.
In my case, I bought it together with ”Nasa Type Number Plate Holder Set” and did a dress-up at the same time, albeit very slightly.
The aforementioned objectives of the purchase have been fulfilled, and the rubber cap to suppress plate vibration is also a nice touch.
In my opinion, Plate seems solid, thick, and sturdy. I searched on the Net and found one with a weight of 210g in the product description. If you don't mind the slight weight of the car, I don't think it will affect your posture, but I was a little concerned about the weight of the Plate.
View detail
I am satisfied!
[K-KON Pro I purchased and installed it together with KITACO License Plate Base.
I thought this product might not be cosmetic (a little expensive for a small parts product), but I bought it simply as a dress-up.
Installation is ELIMINATORSE (2023). It is extremely easy to unscrew and attach, and no special skills are required as long as you have tools.
In my case, however, I was a bit disappointed.
One Point that needs attention ….
Due to the thickness of the License Plate Base and perhaps the thickness of the bracket for installation of the DriveRecorder, the supplied 15mm bolt was too short and could not be reached. (Note that this product does not come with a nut, but an existing one can be used.)
I hurriedly purchased two Hexagon Socket tight BoltM6×25mm, the same type but 10mm longer, at Home center for @80 yen×2pcs.
Although it did not result in a large incident, such action is necessary, so as a preliminary knowledge, please be careful.
I am satisfied with the product.
View detail
To the butt-friendly ComfortSpec!
With my own poor buttocks, I can't ride any Motorcycle for a long distance. (100 km or more?) My butt hurts when I run.
There is a Chance available at a low price, and if it has any effect on improving the symptoms! I bought it.
From the feel of Seat, it is soft and fluffy, and its softness is felt even in the buttocks.
WhiteStitch gives it a more upscale look than NORMAL! I think it is also good.
I have only done a short test run in the neighborhood, but clearly the Comfort feeling has increased compared to NORMAL!
I will add more thoughts after I have run a long distance.
View detail
POSH Aluminum Pillion Belt Cover
About quality and texture Well made aluminum from POSH. The cover gives a beautiful outlook compared to the stock sliver look. About the feeling of use It's a cover that fit perfectly without any lapse in space. Difficulty of installation Less than 15 mins to remove the original screw and place the cover on with the given screws. I hand tighten the the screws as hard as possible. Cost performance and comparison with other products There's no comparison with others as there isn't any similar product around. The price is not expensive but it gives an additional look in your plain looking seat. About shipping and packaging Shipping is not expensive as the the items are small. Items are place in a vinyl plastic bag but no visible damage after shipping. Any concerns, cautions, or advice when purchasing The given screws length is long enough as there's worries about the safety of the belt if the pillon is to grab it. Make sure it's well tightened and theses should not be a problem. View detail
Fits: HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R
It is definitely better than OEM.
I just took it off and put it back on, and so far it hasn't come loose, but if you're worried about it, you need to get it back on.
It looks good, but the price is too high,
View detail
Fits: SUZUKI SV650 N, SUZUKI DL 650 XT V-Strom, SUZUKI DL 650 V-Strom
The CP is also good.
From the name PyramidPlastic, I was prepared to order some more cheap products.
In fact, the FRPParts arrived with a high degree of precision, which is quite high for exterior Parts from overseas.
The bracket engages the Crankcase Bolt firmly, and the engagement with the FRP part is not bad.
However, the supplied Bolt is a bit short, so you may want to prepare a Bolt of about +5mm.
It is not impossible to stick to FRP, but it does not put a load on FRP, and above all, it increases work efficiency by a large margin.
In fact, a separately purchased DesignBolt was used for installation.
I have the impression that it took quite a long time, but it is because it is an overseas parts.
Considering that the FRP parts are solid and cost only 20,000 yen, the cost performance is also good.
View detail
Grip is good
Grip is good and can be held properly.
Double-sided tape does not have a bad bite, but the resin part tends to peel off easily due to temperature changes, etc., even if the tape is degreased properly.:When applying to Unpainted resin, it is better to use strong Double-sided Tape for Vehicleetc.
The Cut surface is standing up and may catch on the seams of the Pants. I used Cutter to cut off the corners.
View detail
Simple is good.
Installation is very easy as it is fixed with a tie band, but I am concerned that it may move in the future as the tightness is weak.
I installed it on my OHLINS front fork and I like the simplicity of it.
There are other, more expensive ones out there, but I think this one will suffice.
View detail
Fits: YAMAHA YZ250, YAMAHA YZ125, YAMAHA YZ250F, YAMAHA YZ450F, YAMAHA YZ250FX
Not yet installed...
It is thick and firm. I wonder if it needs some hang to stick. View detail
Fits: YAMAHA YZ450F, YAMAHA YZ250FX, YAMAHA YZ250F, YAMAHA YZ450FX
I purchased this product because I plan to replace the exterior.
I can't say for sure since I haven't received the exterior yet, but it looks solid, thick, and sturdy.
It seems to need some hang to paste, but I guess it's not a problem since forest roads and Enduro are Main.
View detail
Cost-effective, but requires processing
There is a process to make it like a plastic model.
The letters are attached one by one in Rose, so after folding the nails and taking out the BALI, they are framed in. This process was very enjoyable and had a Petit Custom feel to it.
When installing, the underside of the body interferes with the Fork Cramp, so modification is required.
I shaved more than 5mm at Grinder. (See photo)
Front looks better and I am happy with the low price and enjoyment of PetitCustom.
View detail
Fits: SUZUKI GSX750 KATANA, SUZUKI GSX1100S KATANA (KATANA)
Cool ?
The cosmetics are very good and look very nice. View detail
Newly confirmed as compatible with KF54 (ADV160)!
To JK05.KF47 It works somehow." It was a confirmation of the fit of the However, it was a just fit for ADV160 (KF54). View detail
Many SR riders use it! (p∀p) aha!
[How is it used?
I wanted to put something Iconic on my car, so I decided to use it.
Was the one you received as per Image?
I believe I received the exact image of the product.
The inside of the lid has a tight Rubber so I thought the waterproof property was also good.
Was the installation difficult?
I think it depends on the installation location, but it was not difficult because I just crimped it into the available hole.
More than that - I was worried about the Logo to put inside, mainly because of the angle!
How was your experience with it?
Once attached, it does not bother me. The place where it is attached is not visible when riding, and it is completely self-satisfying.
[Included Parts:were they on?
No, it would be better not to add "Included Parts:" to increase the price.
[Was there anything that disappointed you?
None 。
It is a good Manufacturer that also offers Logo that fits the size.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Before purchasing or installing the product, it is recommended to test the product on a piece of paper, etc., against the part of the car body where you plan to install it to see how it will look, so that you will not make any mistakes.
View detail