Reviews
ChamberFlange Fixed
The Spring of the Flange fixing part of the Chamber section was old and had some play, so I wanted a slightly shorter Type. I was able to fix it with a little pull, and there was no problem in terms of diameter and length, and I was able to use it with a nice one-sided swivel.
The cut was a little short, and the cut end was slanted and did not look good.
View detail
Decent Exhaust Spring
Used for external exhaust system of GSX1300R GSX1300R HAYABUSA
When the exhaust system was replaced with an external exhaust system, the chatter sound of the Gold genus became more loud when the RPM was raised, so it was introduced as a countermeasure against resonance/interference noise.
This product is a type of spring whose Hook rotates freely, just like the springs that come standard with AKRAPOVIC and YOSHIMURA.
It also comes with a Rubber for sound control.
(Although it is shiny and the texture is not so good.)
It seems to have good heat resistance for normal use, but if it is pressed against Cowl or other parts and directly hits the exhaust pipe, it will melt, so care is required.
The spring itself is SUS with a relatively large wire diameter, so it can be tensioned firmly and is rust-resistant and solid.
The Spring is generally as it looks, but one thing to note is the installation length.
Size100mm" means the free length is 100mm.
Note that Tension is not applied unless it is used with some extension.
As per Q&A, it seems that the mounting length is intended to be 120mm.
I tried to install it, but it was a little loose, so I went with the company's M size. (85mm) I bought a new one.
Neck would be the price.
I understand that it is a solid product, but it is a little expensive.
A 4-cylinder Full Exhaust System uses more than 10 springs depending on the type, so the spring alone will cost more than 10,000 yen.
It's a little tough, as you'd expect.
However, the product is solid, and from a quick search, it seems that this size cannot be diverted from AKRAPOVIC or YOSHIMURA's Repair products, so it would be the best solution for those who seek quality over cost.
View detail
Exquisite length
When I changed my Wyvern ClassicR Tail Pipe for a change of pace with a UniversalTitaniumium silencer from Yahoo!
I have always used KITACO's Exhaust Spring, but the 70mm length was not available in Size, so it was a great help.
The springs are thicker than those of KITACO, and the quality is solid, as if it were techserfu.
View detail
I know it when I see it?
I felt the ministry was of higher quality than what I had been using. View detail
No comparison with fake
Quality and Texture Information Yoshimura Quality is Good It keeps the muffler right for the feeling of use Products to buy together yoshimura muffler Installation Difficulty Spring Tool is available Cost performance and comparison with other products Good for Yoshimura muffler WeBike packaging is always great, arriving in a week for delivery and packaging Concerns, precautions, or advice on purchase If you can replace it with a good product, it is okay to use another product, but it will suit Yoshimura muffler View detail
Exhaust Spring
Since we changed to Chinese Silencer, the length of Spring is not long enough, so we bought a longer one.
This length was not available from other Manufacturers and there were few options
It would have been better if it had been made STELLA-less in this length.
View detail
Measure the length carefully.
[How is it used?
When I changed the silencer of YAMAHA XJR400R from MotoGEARΦ100 to K2tecΦ86, the original spring was too long to fix the exhaust pipe and silencer.
So I thought that around 65mm to 75mm would not be a problem and purchased this product.
Was the one you received as per Image?
It was as shown in the Image, but it was surprisingly short... However, I thought that Spring should be stretchable, so I installed it, but it was not surprisingly stretchable.
I was in a tight-fitting state.
How was your experience with it?
I put it on, but it was so tight that it looked like it was about to snap, so I stopped using it...
I think the product is well made and good.
[Points to note]
Everyone should measure the length carefully before purchasing.
View detail
Cheap and just right.
[How is it used?
When I changed the Silencer of XJR400R from MotoGEARΦ100 to K2tecΦ86, the Spring used in MotoGEAR
The exhaust pipe and silencer part could not be fixed firmly because it was about 80mm long.
We measured the length and thought that around 70mm would be just right, so we purchased this product.
Was the one you received as per Image?
I didn't look at the product carefully at first and thought it would come in Silver, but it turned out to be Black.
However, it fit surprisingly well, so I do not mind using it.
How was your experience with it?
It was fixed perfectly as measured.
To be honest, Silencer won't be out without Spring, but the one that needs to be fixed.
Fix it firmly.
[Points to note]
There is nothing special about it, but if I may say so, this kind of Spring should not be overstretched.
Before purchasing this product, I purchased MORIWAKI's 65mm, but the Spring was pulled too much and was too tight. In such a case, there is a possibility that the spring may break during driving, so please be careful.
How did it compare to other products?
Anyway, I liked that the price was low.
It is named "Chamber spring" but can also be used firmly as a 4st for Silencer.
View detail
Fits: HONDA CRF, Others , SUZUKI RM-Z250, KAWASAKI KX250
Installation of AKRAPOVIC Exhaust Spring
[How is it used?
for Repair.
Was the one you received as per Image?
As per Image
Was the installation difficult?
It is easy with a dedicated purchase.
How was your experience with it?
Very good
[Included Parts:were they on?
Included Parts:are not included.
[Was there anything that disappointed you?
None in particular.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Installation Replacement
This is a purchase to replace the other installation with a new one.
Quantity:I would have been happy if it was not 1 Set of 2pcs. but it is cheaper to buy this Anti-vibration Rubber Set than to buy Single Item, so I had no choice.
There were times when the vibration-absorbing rubber cutouts were slanted and terrible, but I was glad to see that this one was not slanted.
View detail
exchange
I purchased this for Spring replacement for Exhaust System installation.
The price is not that high, so it's good.
Would you have preferred it with Anti-vibration Rubber Tube? Yes, I would have.
View detail
quality is worth the price
I used it on my Racer YZF-R25.
Because of the change in Silencer, the position of the Spring hook has changed,
Introduced because of the close proximity between Spring hooks.
The quality is...reasonable for the price. Probably the same as what is sold in CHINA on Amazon or Yahoo!
It is not unusable, but its life as Spring seems to be short.
Be careful not to pull it too hard, as it may break.
The range of use is from about 65mm to about 75mm, but I think 75mm is too much.
I can only see a future where the Spring will break due to vibration while running...
View detail
Exclusive products after all
I purchased this pipe because one of the springs on the Right Side of the exhaust pipe assembly on my Wyvern ClassicR came off and was lost while driving.
It is very helpful to have them out as Repair Parts. I have ordered two spare parts.
View detail
Black color is good
[How is it used?
Spring at the middle pipe joint of Demon150GR external exhaust system was replaced because it started to rust.
Was the one you received as per Image?
2Quantity of Anti-Vibration Rubber on Black Spring:Set。
As per Image.
No Instruction Manualetc. as shown in the photo.
Measured the length and used one that just fit the mounting length of 100mm.
Was the installation difficult?
The only difficulty I had was attaching the Anti-Vibration Rubber to the Spring.
If you have the proper spring hooks, mounting on the car body itself is as simple as hooking the One Side, pulling it, and applying the tension.
I have LargeSmall3Type Spring hooks available based on my past experience fighting various Springs lol.
The Spring hook is used only occasionally, but it is a good thing to have.
My latest favorite is Tone's Spring hook [TSH-165]
How was your experience with it?
I was worried that the anti-vibration rubber would melt because it was in contact with the exhaust pipe, but I checked it after driving and found that it seemed to be large and strong, so I decided to see how it would look.
Since the original SilverSpring has been replaced with a black surface finish, we expect that it will be more resistant to rust!
Above all, it looks Fashion.
When running on previous Spring as well, Beeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee!" I was hearing a contact sound with the RPM, but now that I have this Spring, is the sound muffled by the Rubber? Gwynn." changed to a The volume is about the same. It may be a little quieter … about the same. The contact is within my expectation as it is a self-inflicted disease from the original.
View detail
Manufacturer difference for Silencer
I bought this 95mm silencer spring because it seemed to fit to fix the Trickster Shotgun silencer to the exhaust pipe of my Wyvern ClassicR.
The length is perfect and the Spring is easy to install because one side has a Swivel hook and the other side turns. I have purchased a different size in the past, but the Material:It is a recommendation because Spring is made of Stainless Steel and has good durability. 。
Spring hook for installation (tool) It is easier to have a
View detail
90mm is Exactly for Replacement for MORIWAKID9/L87Spring.
I am using MORIWAKI's Slip-on Silencer on my VTR-SP, but the plating of MORIWAKI's Exhaust Spring (D9/L87's caterpillar type) is weak and rusts a lot. The plating of MORIWAKI's exhaust spring (the caterpillar type of D9/L87) is weak and rusts a lot.:Unavailable for about 2pcs.
I thought it would be better to replace it, but the MORIWAKI Exhaust Spring is expensive, and even if I replaced it, it would rust again soon.
Even if we were to replace it with another company's product, there is no Exactly choice because of its subtle 89mm length and exquisitely not-too-stiff tensile strength.
So, after much research, this DRC 90mm was JUST what I was looking for. It is JUST the right feel that can completely replace it.
Quantity:1 Set of 4pcs. and the price per piece is almost half of MORIWAKI's price at the time of review.
Black chrome plating seems to be moderately rust resistant and has not rusted at all in the two years since I purchased it.
However, I can't guarantee that it will be better than MORIWAKIOEM in terms of corrosion resistance, although I can't guarantee it since it hasn't been driven much during this period.
Also, there is no resonance prevention rubber, but there is no abnormal noise with respect to the VTR.
The only drawback is that it is slightly thicker than MORIWAKIOEM (maybe 1mm thicker) and its glossy black color is quite noticeable. No one but me cares about Level, though.
If you can tolerate that, I highly recommend this product.
View detail
A little stiff.
It is used as Chamber spring with a mounting length of 95mm.
Before this product. MORIWAKI ENGINEERING MORIWAKIEngineerRing:0A02-08709KK11[Exhaust System Replacement Parts] Spring Long I used to use a 1 pc but it came off and went somewhere else, so I bought it.
It was stiffer than MORIWAKI's Spring and could be installed with firm tension.
To compare the hardness, MORIWAKI can be pulled with one hand, but this Spring is a little tougher with one hand.
It is a well-made and good product, but it seems to take a little time for delivery because it is an imported product.
View detail
As expected
It is different from the usual and gives me a sense of satisfaction when I put it on and it is Parenthesis. It is a quintessential YOSHIMURA product. View detail
Rubber is long and good
I was worried about many things, but I decided on the long Rubber and Brand. View detail
As spare parts
Purchased as a spare part for aging deterioration.
The frequency of replacing the exhaust system depends on the type of touring (with or without Panira Case) several times a year.
YOSHIMURAExhaust System springs come with rubber covers with the Yoshimura logo, but after riding, the rubber covers are often damaged due to gapping.
View detail