Reviews
Fits: YAMAHA YZ450FX, YAMAHA YZ250FX, YAMAHA YZ450F, YAMAHA YZ250F, YAMAHA WR450F, YAMAHA WR250F
Consumables Replacement
I had one on my previous Motorcycle. Replaced with this one again.
The finish is not as good as it should be because it is resin parts, but it is sufficient for the needs.
Fitting is also no problem.
View detail
Fits: YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ125X, YAMAHA YZ250X, YAMAHA YZ250F, YAMAHA YZ400F, YAMAHA YZ450F, YAMAHA YZ450FX, YAMAHA YZ250FX
Easy to apply Decal without YAMAHA's stamp
When applying Decal, OEMGuard has a raised YAMAHA imprint, and I bought it because I thought Decal would peel off easily.
It looks good, installs well, and is durable enough when used. No complaints, no excessive interference with the Fork outerTube, and the Decal was easy to put up.
View detail
ACERBIS to Spec. change
My FTR was wearing an ACERBIS Fender, but the shape of the triangle looked awkward when viewed from the front, which was bothersome.
I was planning to buy this product in April, but all the sites said it would arrive in October, so I waited for 6 months and finally bought it.
FTR does not have Up Fender originally, so I had to make it myself from Bracket, but I think it is not that difficult.
I was very satisfied with the natural forme when I put it on and looked at it from the front.
View detail
Fits: HONDA CRF250R, HONDA CRF250RX, HONDA CRF450R, HONDA CRF450RX, HONDA CRF450L
UFO UFO Fork Slider
This one was for a crf250 motocrosser, but I found information on social networking sites that it could be installed on a crf250md47, so I bought it. However, it interfered with the front fork and I gave up on installing it. It was a pity. View detail
Fits: KAWASAKI KX450F, KAWASAKI KX250F, KAWASAKI KX450, KAWASAKI KX250
There are some areas that are slightly different from NORMAL.
[How is it used?
I bought a used KDX220SR a few years ago to own the last 2CycleEngine in my Motorcycle life.
The exterior was in a crumbly condition with no luster due to aging, so I checked Kawasaki OEM parts to refresh it as much as possible, but the exterior except for the light cowl was already worn out. Discontinued. Condition/Status
The paint tends to peel off easily due to the nature of the material, and when I was searching Webike's site, I found that UFO sells Side Panels! (Color:White only) Before it's sold out!" I bought it with great enthusiasm.
Did you receive the item as per the Image?
As you can see in the product introduction image, the design of the Right Side is slightly different from the Normal parts.:The Rubber chamber heat protection is installed, but the rest of the design is of NORMAL standard.
I would have preferred the same shape as the NORMAL, but there is no other choice, so I am hoping to cover it up well with exterior decaletc.
Was it difficult to install?
also There's a certain kind of product." The Bolt fixing holes are slightly gapped, slightly distorted, etc.
Fortunately, this product was lucky because it only required modification of the hole position.
How did you like it?
The gap between the Side Panel and the Rear Fender is also a bit large, but since it is made by the same UFO, it is not so much of a problem.
More than that, the KDX220SR with LusterLuster's Beauty exterior is dazzling & lovely.
Was "Included Parts:" attached?
All images shown are all that are available, Quantities on Side Panel:Pair (for Left and Right) Is Quantity:1 Set.
As mentioned above, the exhaust system on the Right Side panel&Chamber reduces the heat received by the material.:Rubber products are installed.
Were there any disappointments?
I have. It would be punitive to write that OEMs and Other Brand Products are in a state of collapse. I'm just thankful it's there." Product.
As I mentioned above, there are some individual differences that need to be corrected slightly. I can't do anything but pimp it." Please think carefully before making a purchase if you are
Personally New exterior available." I believe that there is nothing better than
Other items that would be helpful
Point and hang of installation
However, as mentioned above, there may be distortion and Bolt holes may be gapped, so temporarily attach it to the car body and correct any points that need to be corrected.
[Availability and clarity of the Instruction Manual
No Instruction Manual is available
If you are able to remove the NORMAL Side Panel, you should have no problem, as you just need to work in the reverse order.
[Notes]
As I've written extensively in the past, it's just that. Other Brand Product So, a certain amount of distortion and Gap will require the buyer to have the guts to correct and install it, and get over it with passion.
[ITEMS TO BUY TOGETHER
Shroud and Rear Fenderetc. can also be replaced for refreshment, and your motorcycle will become beautiful as if it were reborn.
[Opinions and requests to Manufacturer
I know the balance of supply and demand is tight, but could you please resell it?
Once the orders have accumulated to a certain degree." But I would appreciate it if you could help me.
View detail
Awesome Product!
I often travel 3+ hours to a riding spot and usually have the bike strapped down, with the suspension compressed the whole ride there. It DOES keep you from reefing down on the fork springs so tightly and makes it more stable when hauling. Not to mention all the pressure blowing out your fork seals.This keeps that from happening. A must buy to keep your shocks healthy all season. Plastic there's no danger of scratching fork legs.round portion goes on the tire and square portion on the triple clamp. Plus, the material is A+. Great investment for the money.Good piece of hardware. Only complaint is it could be about 2cm longer. Lastly, it stays in place better than the chinese, which I have actually lost more than once. View detail
crf150rRear Fender
Willy's failure to bust it up and purchase Rear Fender.
Before I bought it, I was told that the screw holes might have to be modified since it is not an OEM product, but that was not the case at all!
It was a batch.
View detail
Large effect on Makeover
I replaced the CRF250L Large long Fender with this MOTARD Aero Fender. It is troublesome to measure and fit for drilling holes, but even that is not a problem. [Color] If you can Clear, replacement is easy.
I was worried about contact with the light cowl, but there was no problem at all. The front area looks lighter.
Minus the quality of the included LogoDecal, which is all black and tasteless, it is a cheap and good quality Part.
View detail
Fits: YAMAHA YZ250X, YAMAHA YZ450F, YAMAHA YZ250, YAMAHA YZ250F, YAMAHA YZ125X, YAMAHA YZ125, YAMAHA WR450F, YAMAHA WR250F
Replacement of consumables with Custom WR250F
Used in WR250F
Guide and Quantity because the OEM has worn out to a pretty wadded up state.:I replaced them with a set. I changed both of them to Blue, it looks like Yamaha, Parenthesis is good!
After the replacement, I felt that the running noise decreased.
In my case, I was able to install it by removing the front sprocket and slipping it into the gap between the chain and the swing arm, but I heard that some car models can't be replaced without removing the swing arm from the frame, so I recommend that you check beforehand.
View detail
And as a backup!
[How is it used?
We will have a RenBarrel vehicle available when the race is held and for those who want to experience the off-road.
MinimotoHardEnduro has been in vogue lately, but one thing you can't avoid is Fender breakage.
Also, when you lend it out for a beginner's race, you'll find that it's a three-stage seat style when you get back.
The price is cheaper than OEM, and it is a hassle to look up the part number and put it in the Page of estimate every time, so I bought this one.
I think it is a good point of Other Brand Product that you can choose the color which is not in OEM such as White and Black.
Was the one you received as per Image?
As per Image
Was the installation difficult?
Just remove the Seat and a few Bolts and you're good to go.
How was your experience with it?
It's outside the company, so it won't break easily.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
If you spray Silicon after every car wash, the gloss will last.
View detail
KLX110L UFO Side Panel
Changed the side panel of KLX110L from OEM White to external Black. I am satisfied with the feeling that the whole color was tightened. The accuracy of the installation was also no problem. View detail
Fits: SUZUKI For vehicles from 125cc to 650cc or so
Installed on MTX50R
Because the Fender of MTX50R was crispy due to deterioration, I replaced it.
The OEM FenderBolt was fixed at 3 points, but to prevent interference, it was moved forward a little and fixed at 2 points.:It's plastic and easy to drill. It's also sufficiently hard, so it's large and sturdy even when you put out Speed. I'm satisfied with the look and feel of the OEM.
View detail
Same with OEMs!
A little cheaper than the OEMs, performance is the same as the OEMs!
The sticker is attached to the photo I took, but it is sold separately.
Also, there is a large gap between the Seat and the Seat. There is no problem with the accuracy of the product.
Unpacked, the plastic surface is glossy and clean, and no machining is required for installation. The Truth Pimping. can be done. With normal use, it has been uncracked for a year with every weekend of driving.
It is stored indoors but does not show any deterioration due to UV light.
The color also feels the same as the OEM and is no different than the OEM Front Fender.
View detail
The color tone was different from Image
The shape is the same as the OEM There are no mounting holes, so some modification is necessary It is not difficult to do if you have the tools to do so I bought UFORed with reference to product images and other reviewers, but the color tone is not Image and It was different I also saw some review comments such as "no problem", but that's just my personal subjective opinion, so I can't help it It may be difficult to see because I did not open the package, but compared to Tank and Side cover, it is a little It looks like a pinkish color tone to me It is an exterior part, so I was worried about the color tone and my motivation to install it was depressed I am satisfied with the price, but I am disappointed with Large After all, the color tone should have seen the real thing and compared it Reflection Since the current situation is also painted and used, I feel that I will use this after painting it lightly and matching the color
P.S.; I also ordered a Rear Fender, but it happened to be out of stock by the Manufacturer It was undecided and became Cancellation and was a rakhi & minus;
View detail
Fits: SUZUKI For vehicles from 125cc to 650cc or so
regrettable
I installed it on BRONCO
Large satisfied with everything!
I was supposed to..
There was a problem with the way it was stored on StockYard and the front part was twisted
If it weren't for this, it would have been a perfect score..
I didn't realize it until after I installed it, so I couldn't even return it..
The thing isn't bad, as long as it's not deformed
I managed to make it straighter by holding two pieces of Washer over one of the mounting screws
View detail
Sorry that the mounting holes are not open!
Purchased as RestoreParts of CRM 250 RK. Mounting hole is not open but there is a dent indicating position. Shape and color tone are also UFORed and no problem. It is a shame disappearance that the hole is not open. View detail
Because it has universal nature, is it such a thing?
Purchased as RestoreParts of CRM 250 RK. Since there are Tail lamps and License Plate, they are prepared for processing, so there is no problem that the mounting holes are not vacant. The shape is basically the same as OEM. No hindrance in Design of. View detail
I used it with Universal!
According to Base, I opened the hole and tried using it.
I also used the LED Blinker and it looks good Parenthesis? Haha? I like it and I use it.
View detail
It's stylish
I used it in Universal processing because I got a Wound on fall. It also serves as LED BlinkerBase. I finished it very well! View detail
I got it on LITTLE CUB (Ishimichi)
Michelin's PilotSTREET, Grip performance is great, but it is discovered that you can jump up the moisture on the road diagonally upward.
Therefore, such as after the rain will be muddy to the whole body.
So I tried installing this Fender forcibly. (For the installation, we cut off the rear part at once. )
Performance for Motocross is expected!
There is a thicker resin than CUB's Fender, it worked well for bouncing up.
It looks ticky "Black squid" It seems that it stuck (~_~;)
View detail