Reviews
Fits: YAMAHA YZ450FX, YAMAHA YZ250FX, YAMAHA YZ450F, YAMAHA YZ250F, YAMAHA WR450F, YAMAHA WR250F
Consumables Replacement
I had one on my previous Motorcycle. Replaced with this one again.
The finish is not as good as it should be because it is resin parts, but it is sufficient for the needs.
Fitting is also no problem.
View detail
Fits: KAWASAKI KX450F, KAWASAKI KX250F, KAWASAKI KX450, KAWASAKI KX250
There are some areas that are slightly different from NORMAL.
[How is it used?
I bought a used KDX220SR a few years ago to own the last 2CycleEngine in my Motorcycle life.
The exterior was in a crumbly condition with no luster due to aging, so I checked Kawasaki OEM parts to refresh it as much as possible, but the exterior except for the light cowl was already worn out. Discontinued. Condition/Status
The paint tends to peel off easily due to the nature of the material, and when I was searching Webike's site, I found that UFO sells Side Panels! (Color:White only) Before it's sold out!" I bought it with great enthusiasm.
Did you receive the item as per the Image?
As you can see in the product introduction image, the design of the Right Side is slightly different from the Normal parts.:The Rubber chamber heat protection is installed, but the rest of the design is of NORMAL standard.
I would have preferred the same shape as the NORMAL, but there is no other choice, so I am hoping to cover it up well with exterior decaletc.
Was it difficult to install?
also There's a certain kind of product." The Bolt fixing holes are slightly gapped, slightly distorted, etc.
Fortunately, this product was lucky because it only required modification of the hole position.
How did you like it?
The gap between the Side Panel and the Rear Fender is also a bit large, but since it is made by the same UFO, it is not so much of a problem.
More than that, the KDX220SR with LusterLuster's Beauty exterior is dazzling & lovely.
Was "Included Parts:" attached?
All images shown are all that are available, Quantities on Side Panel:Pair (for Left and Right) Is Quantity:1 Set.
As mentioned above, the exhaust system on the Right Side panel&Chamber reduces the heat received by the material.:Rubber products are installed.
Were there any disappointments?
I have. It would be punitive to write that OEMs and Other Brand Products are in a state of collapse. I'm just thankful it's there." Product.
As I mentioned above, there are some individual differences that need to be corrected slightly. I can't do anything but pimp it." Please think carefully before making a purchase if you are
Personally New exterior available." I believe that there is nothing better than
Other items that would be helpful
Point and hang of installation
However, as mentioned above, there may be distortion and Bolt holes may be gapped, so temporarily attach it to the car body and correct any points that need to be corrected.
[Availability and clarity of the Instruction Manual
No Instruction Manual is available
If you are able to remove the NORMAL Side Panel, you should have no problem, as you just need to work in the reverse order.
[Notes]
As I've written extensively in the past, it's just that. Other Brand Product So, a certain amount of distortion and Gap will require the buyer to have the guts to correct and install it, and get over it with passion.
[ITEMS TO BUY TOGETHER
Shroud and Rear Fenderetc. can also be replaced for refreshment, and your motorcycle will become beautiful as if it were reborn.
[Opinions and requests to Manufacturer
I know the balance of supply and demand is tight, but could you please resell it?
Once the orders have accumulated to a certain degree." But I would appreciate it if you could help me.
View detail
KLX110L UFO Side Panel
Changed the side panel of KLX110L from OEM White to external Black. I am satisfied with the feeling that the whole color was tightened. The accuracy of the installation was also no problem. View detail
Fits: SUZUKI For vehicles from 125cc to 650cc or so
Installed on MTX50R
Because the Fender of MTX50R was crispy due to deterioration, I replaced it.
The OEM FenderBolt was fixed at 3 points, but to prevent interference, it was moved forward a little and fixed at 2 points.:It's plastic and easy to drill. It's also sufficiently hard, so it's large and sturdy even when you put out Speed. I'm satisfied with the look and feel of the OEM.
View detail
The color tone was different from Image
The shape is the same as the OEM There are no mounting holes, so some modification is necessary It is not difficult to do if you have the tools to do so I bought UFORed with reference to product images and other reviewers, but the color tone is not Image and It was different I also saw some review comments such as "no problem", but that's just my personal subjective opinion, so I can't help it It may be difficult to see because I did not open the package, but compared to Tank and Side cover, it is a little It looks like a pinkish color tone to me It is an exterior part, so I was worried about the color tone and my motivation to install it was depressed I am satisfied with the price, but I am disappointed with Large After all, the color tone should have seen the real thing and compared it Reflection Since the current situation is also painted and used, I feel that I will use this after painting it lightly and matching the color
P.S.; I also ordered a Rear Fender, but it happened to be out of stock by the Manufacturer It was undecided and became Cancellation and was a rakhi & minus;
View detail
Fits: SUZUKI For vehicles from 125cc to 650cc or so
regrettable
I installed it on BRONCO
Large satisfied with everything!
I was supposed to..
There was a problem with the way it was stored on StockYard and the front part was twisted
If it weren't for this, it would have been a perfect score..
I didn't realize it until after I installed it, so I couldn't even return it..
The thing isn't bad, as long as it's not deformed
I managed to make it straighter by holding two pieces of Washer over one of the mounting screws
View detail
Sorry that the mounting holes are not open!
Purchased as RestoreParts of CRM 250 RK. Mounting hole is not open but there is a dent indicating position. Shape and color tone are also UFORed and no problem. It is a shame disappearance that the hole is not open. View detail
Because it has universal nature, is it such a thing?
Purchased as RestoreParts of CRM 250 RK. Since there are Tail lamps and License Plate, they are prepared for processing, so there is no problem that the mounting holes are not vacant. The shape is basically the same as OEM. No hindrance in Design of. View detail
Since the OEM part of 08D-TRACKER X was too sharp, I'm glad it became more stylish. Since it doesn't have an installation hole, you need to make a gauge by measuring the hole pitch of the OEM part, and pierce a hole with a drill while checking its cle
Since the OEM part of 08D-TRACKER X was too sharp, I'm glad it became more stylish.
Since it doesn't have an installation hole, you need to make a gauge by measuring the hole pitch of the OEM part, and pierce a hole with a drill while checking its clearance. It's quite easy, but you need to be careful for you've got only one chance.
I don't drive on rainy days, so I haven't experienced mud spattering, but it looks like you're going to get drenched.
View detail
it becomes an anyhow sharp silhouette and he is smart! however, mud splashes should bear -- 笙ェ
it becomes an anyhow sharp silhouette and he is smart! however, mud splashes should bear -- 笙ェ View detail
Although the motard fender made from a daytona was stuck before, it changed into the time-tested UFO aerofender. From Aceh or a daytona, there is no sharpness and a favorite is carrying out the pure twist refreshing. I think that the front number
Although the motard fender made from a daytona was stuck before, it changed into the time-tested UFO aerofender.
From Aceh or a daytona, there is no sharpness and a favorite is carrying out the pure twist refreshing.
I think that the front number and affinity of the same UFO are an outclassing.
View detail
The fender of UFO was processed into carrying out custom of XLR250RMD16, and it was made the down fender, and attached. In ordinary one for OFF, since it was long, when the shorter object for motards was made the down, it suited the ska tune well exac
The fender of UFO was processed into carrying out custom of XLR250RMD16, and it was made the down fender, and attached.
In ordinary one for OFF, since it was long, when the shorter object for motards was made the down, it suited the ska tune well exactly.
It is whether a down is also good in it being unexpected!
View detail
D trucker is equipped. It attaches and easy. However, the spray of the day of the rain which leaps up from a front tire is not odd, and on a track, since it pounces as if it was taking a shower, cautions (preparedness) are required. One articl
D trucker is equipped.
It attaches and easy.
However, the spray of the day of the rain which leaps up from a front tire is not odd, and on a track, since it pounces as if it was taking a shower, cautions (preparedness) are required.
One article from which unfashionableness escaped in looks and which cost performance has satisfied highly.
Although black is used, it will pass in five years, gloss is lost by aged deterioration, although it is a minus that a crack has come to be conspicuous a little, it attaches, and I think that it was good.
Its quality is unexpectedly high, and even if the sticker at a tip will pass for five years, its thing without big discoloration is glad.
View detail