Reviews
No problems with deterioration of Touch, etc., but replacement
I had no particular complaints about the BrakeTouchetc. but decided to replace it when the mileage reached about 4,000 km.
The replacement of the ABS hose required some care as there are various precautions to be taken, but since the installation instruction manual is included, the replacement work was done without any particular problems.
If you are not familiar with Brake maintenance, it would be better to take a picture of how to install the NORMAL Hose so that you don't have to worry when you install it. (All external Hoses are the same).
Touch is no different, and perhaps the best effect is the improved texture of the banjo bolt.
View detail
Protecting the Horse
The hose was rewound to the point where it meets the body of the vehicle.
It would be good to use 100-yen ones, but it is troublesome to check the Size and Fitting, and it costs about 300 yen, so I bought this one.
It is a special product and fits the brake hose just right, and the texture of the material feels supple.
Since it was only used to protect the contact point, 1m was almost too much.
View detail
Standard Custom
4mini Standard Custom??
Red and Blue Collar Accent best!
The Rear hose and Swing Arm are also a good match!
Custom feeling has increased.
View detail
SWAGE-LINE:Swage lineCopper Washer #3 installation
[How is it used?
SEA BASSOEM Parts Brake Caliper Assembly brembo STYLEMA [Stillma] For 108mm mounting
[Points to note]
Be careful when installing as it applies Torque.
View detail
Fits: KAWASAKI ZRX1200S, KAWASAKI ZRX1200R, KAWASAKI ZRX1100, KAWASAKI ZRX1200S, KAWASAKI ZRX1200R
Exactly
As expected from a car model! Everything was just fit!
I could see the difference from FirstTouch even with Normal caliper.
View detail
for Brembo
The banjo bolt was also changed in order to replace the caliper with brembo. View detail
Fits: KAWASAKI ZEPHYR X, KAWASAKI ZEPHYR400
Mesh hose for rear brake
It looks cool, the Crimp part is covered and looks luxurious and sturdy compared to other Hoses. View detail
I would have liked to have blacked it out.
I used to use the same size Stainless Steel color at the entrance of Caliper, but I decided to change it to Black color to match the Black color of brembo's Caliper. I am satisfied with this change, even though it is only for appearance. View detail
Brake CaliperCustom accompaniment
Purchased in conjunction with Caliper replacement.
We are also considering MASTEROverhaul at a later date, so the Quantity:I think 1 pc. spare in 1 Set of 3pcs.
The inside diameter is a little loose, so there is no feeling of being snugly fitted, and you can also feel the responsiveness of the crush feeling when Torque is applied.
The thin cheap ones don't feel crushed when Torque is applied, so I'm worried about using the Torque wrench, but these are thick-walled and fine.
View detail
Slim Hose is Refreshing and ◎
I like that the hose is thin and refreshing to handle. View detail
Good goods
I feel better when I grip the Brake. View detail
Banjo is hard to tighten, but
Stable braking force can be applied from the start of stepping on the rear brake to the maximum large step. Since the braking effect does not change with the amount of pressure, it is possible to assume the final braking force when stepping on the brake, even during strong breaking. View detail
Banjo adapter
Change from SWAGE-LINEHoseStraight AdaPig I'm happy with the angle and the extra room it gives me. View detail
SWAGE-LINE Swage line Rail position banjo bolt
I installed it on a GPZ900R A11 Normal caliper.
I have no problems at all with the quality and Size.
View detail
trust
There are many inexpensive banjo bolts on the market, but I chose the reliable Swage line because I didn't want anything to happen to my brakes when I was on the road. I have used them on two of my motorcycles and have had no problems, so I am satisfied with them. View detail
Rear brake switch
[How is it used?
To be replaced by PLOTType originalfootpeg this time.
OEMBrake switch is no longer available and we considered installing 3Type hydraulic type.
Photo 1:The product in question (¥9,900)
Photo 2. babyface (¥4,950)
Photo 3. Purchased at a mass retailer (about 5,000?)
The product in question must be purchased separately from Banjo bolt.
Photos 2 and 3 were rejected because the Master Cylinder has been erected and looks like a rear cowl.
Was the installation difficult?
Brake fluid had been removed, so it was not difficult at all.
How was your experience with it?
There is no problem.
[Included Parts:were they on?
I appreciate that it comes with a Crash washer.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
It was a little short!
I set it to 350mm and it was a little short.
I used a Bracket to extend the Hose a little.
I set the Caliper banjo adapter to SD20° and twisted the bracket attached to the swing arm a little because it interfered with the spring when I put it around as shown in the picture. Cylinder side is set to 20°.
I will challenge again to handle the Hose after replacing the Swing Arm sometime in the future.
View detail
usually
It is well worth the price. It's beautiful and solid because it's Stainless, it doesn't overtighten and crush easily like Aluminum. View detail
There is no pugnacious feel to the Brake pedal.
Since the front brake hose of the same product was replaced,
To balance, the Rear Brake hose was also replaced.
I am sorry, but I am not sure if this is a good idea.
Rear brake also had a pugnacious feel in NORMAL,
After the replacement, the touch was changed to Snap, and it was very Control.
It is now easier to do so.
The replacement was completed easily due to the fact that the ABS was not attached.
If you are going to replace them, I definitely recommend replacing them front and rear.
View detail
I like the pushing feeling when I grip the Brake lever.
The Touch of Brake with Snap is very good.
I wished I had replaced it earlier.
I did the replacement myself, but Brake fluid replacement
There were no kills at all, so I referred to You Tubeetc.
It took about 4 hours back and forth, but we made it.
Done.
The all-important Air extraction is also perfect.
If you are familiar with the exchange, the whole process should take about 2 hours.
I believe the entire process will be completed.
View detail