Reviews
I should have put it on sooner.
I was worried about the price and whether I could install it by myself for about 2 years, but finally I bought it.
Spring couldn't hook me up in any way, and I was on Net. "Remove RubberDamper, apply Spring first, assemble, then put RubberDamper back on." It took about 30 minutes to complete the process.
This will make maintenance easier. I wish I had put it on sooner. (^o^)
View detail
It's OEM Parts, so it's not flashy, but...
I was going to use it as a maintenanceSTAND for the Motorcycle.
I have not had any difficulty with Spring, which is a difficult installation.
Once completed, it was still not difficult.
View detail
OEMCenter Stand
OEMCenter Stand, so the Fit feeling is excellent.
Does this make it easier to do Chainetc. maintenance?
Installation was completed without any problems with Driver and Radiapen.
If the Driver is Spring-loaded using the Lever principle, there is no particular need for a Spring hook.
Cushion rubber is hang attached after STAND installation.
View detail
Fits: SUZUKI DR-Z400SM, SUZUKI DR-Z400SM, SUZUKI DR-Z400SM, SUZUKI DR-Z400SM, SUZUKI DR-Z400SM
Rear caliper guard
I have been searching high and low, everywhere even the local distributor even the parts list and nowhere be found. Chance upon it when checking on webike, was so excited that i got it! View detail
Installed on a Type 3 GSX1300R HAYABUSA to prevent inner thigh heat
Installed as a countermeasure against hot inner thighs coming in contact with the Frame when the foot is down while the vehicle is stopped.
Installation is easy with double-sided tape, but it is good with no signs of coming off.
I didn't want to put it on because I prefer the way it looks without it, but when I actually put it on, I found it was not as bad as I thought it would be.
The heat shielding effect has not yet been experienced, but is expected Large.
View detail
It fits perfectly and eases the heat.
I bought the GSX1300R HAYABUSA because even though it is now in its third generation, the GSX1300R HAYABUSA is so hot in the summer months that I almost burn myself with Frame heat.
It doesn't completely block the heat, but it's far better than nothing.
I chose this product because it is sure to fit, but I personally feel that it is a bit half-hearted because it does not completely hide the Frame. I think this is a matter of preference.
View detail
While stocks last.
This is an Option product for the 2nd generation GSX1300R HAYABUSA, so it will be hard to get when the stock runs out.
As expected of an OEM product, it was also Exactly the same for the New Model GSX1300R HAYABUSA.
View detail
Satisfied with the look and feel of PetitCustom
[How is it used?
This is Carbon style, but I installed it for custom feeling.
Was the one you received as per Image?
If you look at it carefully, it's obvious that it's a fake Carbon, but at a glance, it's a good enough Parenthesis.
Was the installation difficult?
Just use double-sided tape and stick it on, so it's easy.
How was your experience with it?
Function? It's more of a look than a function, so I'm happy with that.
It's Carbon wind, so the price is Reasonable.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
There is none
View detail
Exactly the same for the New Model GSX1300R HAYABUSA
I used to use it on my Model 2, but I bought it because the frame shape was very similar. When I ride on the street, my feet hit the frame and it is very hot without it, but thanks to this, it became comfortable. View detail
SEA BASSFrame cover
It is a Carbon Style Frame cover, but it is supposed to be excellent for heat exhaust etc. in the summer. View detail
Dissatisfied with the shop's response
When the product arrived and started to assemble, Nut was missing 1pc.
I could not install it. I had to wait a long time for my order and the product was defective.
I emailed them about it but they never responded and Nut never arrived.
This is the worst company. I've never been treated like this before.
View detail
Neither good nor bad OEM
I bought this because I do a lot of maintenance and the Maintenance Stand was a pain in the ass.
As for the installation, it is difficult to pull the spring to put the Rubber Bush at the end as everyone wrote, so I bought Spring Remove KIJIMA:KIJIMA item number:302-2041 first.
Because the place where the Center Stand is installed is prepared beforehand in the body of the car, ignore the place of the Rubber Bush installation of the Instruction Manual and do the rest as it is.
Install the spring by pulling the spring with the Spring Remove. Even if you use this tool, you need to use full force.
Apply Grease that is not in Included Parts:to the CenterROD.
Finally, Grease up the Spring and the hooks and you are done.
Maintenance is now easier, but Side Stand is harder to get out.
Furthermore, when the extension which expands the ground area is attached to the Side Stand, it interferes with the Center Stand, so it becomes necessary to cut the extension.
View detail
For the heat.
I bought it to prevent the frame from getting hot when stopping or driving at low speeds. I haven't done any touring yet, so I'm not sure how effective it is at preventing heat, but the dress-up effect is pretty good. View detail
SCRAMBLER
If you want to look like a SCRAMBLER, this is for you!
But it's expensive!
But I'm happy.
View detail
For my daughter's GSXS.
I bought this to put three in a row on my Garage... my daughter will not use it at all! (Lol)
I watched a lot of videos and struggled to put it on... orz
If it were easier to use (even for non-powered women), it would have been rated higher... too bad.
View detail
For my daughter's GSXS.
Bought this to put 3 cars in the Garage.
I installed it while watching various installation videos......but it was very difficult to install the Cushion rubber at the end.
I installed it, but... I'm the only one who stops at Center Stand. (Lol)
Daughter and wife always use Side Stand as a hassle
┐ (´p.s.) backwards (shaking)
If only it were easier to install and use...too bad.
View detail
That would be handy
I bought this for my new Special Knife Address 110 for commuting, and although the engine stops when I use the normal stand, this Side Stand is very convenient because I can run it warm with the stand on. View detail
To prevent heat
I bought it as a countermeasure against heat during touring because the Frame gets so hot that it seems to burn during touring in midsummer.
It was very easy to install with Double-sided Tape, and there was no problem if the positioning was done carefully.
It was thought that it was a heat measure, but it is a feeling that it is possible to forgive it even if the effect is a little sweet well Parenthesis.
View detail
Center Stand is recommended.
It is OEM Product, so there is no problem of installation and usability.
Wheel cleaning and chain maintenance are also more efficient, which is a good thing.
No scrubbing at the corners, so far.
It is said that Rubber for buffer is attached first in installation.
If the Spring is very hard and there is a Rubber, it takes a lot of strength even for an adult male.
It is easier to install the Spring if the Rubber is attached last.
View detail
I want you to have it on from the start.
I bought this because the Swing Arm has a screw hole for installation and I felt it would be unnatural if it didn't have one.
It is resin, but it is solid impression, and it is OEM Parts.
I looked at the Parts List and it was Option.
I'm new to Off, so this part is like a good luck charm right now.
View detail