Reviews
Almost satisfied
It's been a while since I bought it, but I put it on my Swing Arm as one point. striker's logo is my favorite, and I really like the design, The large size is just right, and the Black Swing Arm with the Red One point is a little makeover.
As usual, I degreased the object with Silicon-off before applying Sticker, but since this Sticker has almost no elasticity, it was quite difficult to apply it neatly on a curved surface. Also, the glue is not very strong, so it would be better to apply it only once.
However, the glue is not very strong, so even if it peels off, I don't think I will have any trouble cleaning up the remaining glue.
I will try again when it comes off.
View detail
Sticker on Under Cowl
It could have been a little larger. View detail
For Racing concept Small but not for mini!
[How is it used?
Striker's Racing conceptFull Exhaust System is used on a YZF-R25 that is being racerized.
Although the Silencer is located in a position that is less likely to be damaged than a normal Exhaust System due to repeated falls.
The glass wool was worn out and was a mess, so I bought a new one while replacing the glass wool.
Was the one you received as per Image?
The design and texture were just like the Image without any complaints, but... the Size "Small" It's big on Habit of Habit!
Apparently, the Racing concept of the R25 is For Power mini of Emblem seems to have been correct.
It's my fault for not checking properly.
By the way, the one for Power mini is "part number : 0SREB5". Check Emblem's Design carefully before buying.
Was the installation difficult?
I have not installed it because it is too big, and I don't want to put a strange load on the silencer band.
If you can do a normal Silencer Overhaul, this is an easy task.
Just skip Rivet's head in Drill and Riveter with liquid Gasket on the new Rivet.
How was your experience with it?
Too big for Silencer up to 250cc! But it's too good to waste, so I'll put it on Silencer's Reverse side and make it DoubleEmblem....
[Included Parts:were they on?
RivetQuantity in a courteous manner:It comes with 2pcs! but the Material:It was an Aluminum umbrella and the shaft was rusty with an iron Rivet.
[Was there anything that disappointed you?
Emblem from Racing conceptSeriesStandard Equipment. I would be mistaken if I were told that this is the case.
Since we know which Silencer is being used for which buzz, please make sure that the Manufacturer has a good setup.
View detail
Fits: HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SF
Mounted on cb400sb NC42
The item arrived and there was a chip at the very edge.
I used it as it is because it is out of sight when installed.
I'm a little disappointed.
If the OEM footpeg is attached, the Hexagonal Wrench could not be installed without removing the footpeg, which was quite a challenge, but I was able to use a hexagonal wrench from a 100 yen shop that was just short enough for the job.
It would be easier to remove the footpeg or replace the bolt with one that can be rotated by Spanneretc.
It looks a little different, but...
View detail
Overall, it's subtle.
The screw to fix the License Plate Light to the Bracket is not included.
The support was very good and fast.
I think the Design and texture of the product is good.
Unfortunately.
The gap to pass the wiring is large, and if you don't take measures, mud will come in considerably.
The Blinker Bracket interferes and makes it difficult to install the Number.
Since it is more expensive than other products, I wanted to make sure that the gaps were especially addressed.
View detail
Fits: KAWASAKI ZrX1200ZrX1200 DAEG, KAWASAKI ZRX1200R
High quality.
I don't know about the durability of this product, but I think the quality is very good. View detail
Although nothing influences the engine performance, since a Parenthesis is good, it changes just.
Although nothing influences the engine performance, since a Parenthesis is good, it changes just. View detail