Reviews
BABY Face Engine slider CBR600RR
The installation position is Exactly, high quality, and I am satisfied with it. View detail
Fits: DUCATI SCRAMBLER FULL THROTTLE, DUCATI SCRAMBLER CLASSIC, DUCATI SCRAMBLER ICON, DUCATI SCRAMBLER URBAN ENDURO
Easy Stand Hook installation
Stand Hook is very useful for chain maintenance and other work with the rear tire in the air.
This product was easy to install, just tighten with a Hexagonal Wrench, and it worked without any problems.
The product looked great and was satisfactory.
View detail
The construction is very good, but when you actually use it, it is very difficult to use.
The make is very good and looks OEM 。 I put it on my MOTO GUZZI which does not have a helmet lock, but it is attached without any discomfort. 。 However, in actual use, the helmets touch the exhaust system because of the low position of the helmets. View detail
Parenthesis OK
I replaced it for use at Circuit.
Anodized is Parenthesis good.
Installation can be done according to the Instruction Manual.
It's easy
No processing was required.
Position can also be changed, as the range is large.
It was a challenge to get Shift to work together.
I fell over once, but only the tip was shaved off.
Repair Parts is expensive, so we have to go to compatible parts.
Change.
It is good because it is not dedicated.
View detail
Design is good
Simple and can be mounted to allow for subtle orientation and positional modifications. Good. View detail
Very good looking, but...
Pulling on the brake wire is important, but securing the rotating bracket is impossible with a screw lock, and the bracket inevitably moves. However, I think that a more ingenious bracket is needed instead of just using the OEM bracket. View detail
Maybe I don't need Front.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
I thought that the Protector has little protrusion, and since it has a Radiator, I think it is not so meaningful even if it is attached, since it is originally wide.
I hope you don't experience any effects.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
stick out firmly.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
The back seems to stick out and make sense. I hope you don't experience the effect.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
For Dress-up
I removed the Tandem Footpeg to make a Single Seat, so I installed this one. I have read some other reviews that the holes are gapped, but this was not the case with mine. View detail
Slider
I installed it myself and it was very easy. I can ride my motorcycle with peace of mind. View detail
sc40 Bar End Replacement
I had been thinking of a thin Bar End because a large Bar End would make it difficult to get in and out of the Apartment's bicycle parking lot, but I was unsure because I couldn't kill the vibration.
Stainless Steel Bar End Short in BABYFACE
It is not so large, and being Stainless Steel, it is heavy and strong, and vibration was reduced.
It feels easier when the slight vibration coming to the hand is reduced.
View detail
Various position adjustments are possible.
Installed on a YZF-R6. Racefootpeg is listed as not compatible with ABS, but I was able to install it by bending the brake pipe. (I was able to install it by bending the brake pipe.)
Brake switch must be hydraulic.
Position is currently used at the bottom and front of the first for my body type.
One part of the Cowl needed to be cut because the tip of the Shift Pedal was in contact because of the Under Cowl of Magical racing.
I often use the rear brake, so I was able to adjust the position to one that is easy to operate, and I am satisfied.
View detail
Nice and discreet.
The installation method was easy to understand and quick and easy to install.
If the Bolt on the Engine Mount can be removed. But, it's a story of "if".
If you are a woman, or if you are not strong, or if you don't have the proper tools, have the store put them on for you.
I am very satisfied with this product because it is not a big slider, it is small in shape, and it does not require any processing for cowl.
So far I haven't had any help. (Not falling down) I don't know how effective it is.
View detail
Fits: SUZUKI KATANA, SUZUKI GSX-S1000, SUZUKI GSX-S1000 GT
I think it's a good costumer
I think this product is cheaper and more cost-effective than other companies' products. View detail
I think it is cosmetically good.
I think it is a good product in terms of cosmetics, but I would like to see some improvement in design. View detail
Change in appearance.
It is a self-satisfied part with no functional significance. View detail
BABYFACE:Babyface Racing hook
I have installed this product due to the elimination of the Tandem step. It is not intended for use, but for one point customization. View detail
The color is different from the picture.
I liked the design, but was a little disappointed that the gold was a strong orange gold! View detail
Product with good texture
Babyface
RaceConcept. RaceConceptHandlebar Kit Up typeSIDEOffset
UP45-10
Handlebar240mm
Item Number : R05-HS47100M
car Species:YZF-R25 (8BK)
The texture is very good and beautifully finished. Unfortunately, the brembo radipon could not be installed this time because it interferes with the Cowl.
View detail
Wow that's cool
I installed it because I was lonely around the Front.
Circuit also runs, so Protector in the event of a fall.
I hope it will be ??
View detail