Reviews
Bolt is too long and cannot hold Body in place.
The bolt is long and the Motorcycle's cap nut is welded on, so the body cannot be fixed. I noticed that the keyhole is not visible when it is facing downwards, and it is difficult to use it. I would recommend the sideways keyhole of other manufacturers. View detail
The product itself is good, but installation is quite time-consuming and the Instruction Manual is not very comprehensive.
The installation was far more troublesome than expected.
The fact that it is troublesome to install means that Helmet may never be stolen because it is difficult to remove.
I installed it myself, but if you are not a self-starter, it is better to install it at a motorcycle shop.
View detail
At any rate, I wanted a Holder.
At first, I wanted to be able to fix the Helmet, so I purchased and installed it.
When I installed it, I noticed that I could not reach the D Ring as it was, so I urgently purchased an extension Holder and used it.
View detail
It is difficult to use with S1000 because it is downward facing.
Exclusive Design, but the lock part is facing downward, so it is hard to hang the helmet. Also, to mention a small point, the body of the product adheres to the exterior and is slightly scratched by vibration, etc. If you apply anti-scratch film, it is no problem. KIJIMA's Helmet lock is better in usability. View detail
Some types of helmets cannot be installed without modification.
ARAI's Jet helmet can be hooked directly to the Ring.
With the full face of the Shorey, you can't hook it directly with the Ring.
The only way to hook it up is to use Wire.
I don't know if it depends on the Manufacturer of the helmet or the type.
Maybe using Wire is the way it should be used....
The product is easy to install.
Even as an amateur, I was able to install it in about 30 minutes.
It would be correct to put it on the Center Stand side.
I installed the Exhaust System on the Right Side.
View detail
Necessities for Tandem
[How is it used?
Used during Tandem
Was the one you received as per Image?
Lighter and easier to use than Image
How was your experience with it?
I used to have two Helmets hooked to my Holder, but this product makes it easier!
[Points to note]
The orientation of the two Helmets might need a bit of a hang.
How did it compare to other products?
We also considered the Wire type, but chose this one due to the level of safety against theft
Other items that would be helpful
Installation Point or hang
Orientation of the two Helmets
Items to buy together
? None in particular.
Opinions and requests to Manufacturer
? None in particular.
View detail
For now Then it's antsy, but there's a lot to be concerned about
[Was there anything that disappointed you?
We knew from looking at the product images that the Helmet was going to be difficult to install
I have found the installation of the product to be very cautious and difficult, even when using it
More than that, when I actually installed the X-14
Helmet interfering with Billionfootpeg and Tandem Footpeg according to
I was very concerned about the scratches that could be made to the Helmet
It's a product that is installed in a way that makes it look like it could just slip out of your hand and fall off
The only thing that could damage the Helmet if you're not careful is the one thing that could damage it
I honestly don't think it's good for my mental health
I don't care if Helmet is scratched! If this is the case, it's not a problem
I don't think many people who buy a Motorcycle like the SC82 don't care about it Hmm..
To make it easier to install, there is a Helmet Anchor that is available on the market
As for the SC82, if you try to use the Helmet Anchor, there is no doubt that you will be able to use helmet hits the footpeg with a thud
I'm looking for ways to make effective use of this product
I don't really feel like using it as is
Do you have any wishes or improvements you would like to make for the Manufacturer?
I would like to see the shape of the HelmetBracket to make it easier to install
I want it to be possible to lock without having a keying device (Dial type, etc.)
I want you to consider the interference of the Helmet when it is actually installed
[Do you have any products to compare it to?
There is no other helmet holder for this type of car
There was no comparison, but after the installation of this product
We are considering a Dial-style Wire locketc
What made you decide to buy?
The helmet holder of the SC82 is located in the Tandem seat
If you install a single seat cowl, there will be no helmet holder It was
This was a problem for me when I was touring
This product was first sold as a Helmet Holder, so it was the first to be sold as a Helmet Holder
Purchased
How was your experience with it?
First impressions Very difficult to use It was
I'll make sure they don't steal it for now If you think it's just for the sake of it
My impression is that it's not a problem
The first thing I did was Neck to increase the number of Keys I had on hand
Since this is a Key less vehicle, it would be nice if you could make it a Dial type etc
It's a desire to be happy with less hassle
Also, the part of the Helmet that goes through the Bracket is very narrow
It is difficult to install the Helmet
You have to pull pretty hard on the Helmet side
I had a hard time reaching the lock part
Also, the rod that goes through the bracket will slide a little bit, and there will be a gap between them
I'm going to run a bracket through it
The moving side of the stick will open upward when viewed from the ground
It is difficult to hook and lock the HelmetBracket
I thought that if my hand slipped a bit, I might drop the Helmet
Was the installation difficult?
The installation itself was very easy
Remove the two bolts that are holding the Tandem Footpeg in place
The product is inserted between the body and the Tandem Footpeg and
Just tighten the two Bolts with the prescribed Torque
【Please tell me the installation point and hang】
To ensure that the Tandem Footpeg mounting angle is not Gap
First of all, Quantity:With the 2pc Bolts temporarily fixed
It's a good idea to tighten the Bolt while supporting the Tandem Footpeg at a normal angle
[Was the Instruction Manual easy to understand?
It wasn't a particularly helpful Instruction Manual, but it was
Since the installation method is more obvious than it looks in the first place, Parts
I didn't have to worry about it
If I had to choose, I'd say it's a vehicle-specific part
Multiple Patterns are listed in the Tightening Torque section
"A little longer" I felt that
[Included Parts:were they on?
The key cylinder body and the key for unlocking the door
It also includes an Instruction Manual, which is just a little bit of feeling, and a Sticker I did
[Others]
As for Matching to the body of the car, I think the design of the car is good because it doesn't look like it's floating and has a sense of unity I thought
If the key functional aspects of the product were excellent, I would have no complaints..
View detail
It goes on easily
The good thing is that it is easy to put on with Bolt On
The Bad Full face Shield as it attaches to the Right Side of the Motorcycle It's very difficult to remove the keyhole because the keyhole is hidden by the Helmet if you hang it in a direction where the keyhole doesn't hit the keyhole You should have a Helmet lock on the Left Side of your motorcycle As you can see from the pictures of the products, the Plate and the Plate that co-tightens the Bolt are It protrudes a little bit downward from Squidward and Nassert's exclusive Stay and Magical I don't think it's attached to the racing Stay, Nojima was also a dedicated Stay, but I'm not sure if I can change the shape I can't say for sure because I don't remember, maybe, but lol
View detail
To use
Maybe only you, Helmet (ARAI RX7) It's too narrow to catch on to DRing so it's hard to do.
Helmet Lock It is useless if there is something like Assist, but it may weaken on crime prevention.
View detail
I am lost with KIJIMA ...
I got lost as KIJIMA made, I bought this.
Although KIJIMA was attached to another Motorcycle, I purchased it because I thought that there would be a problem if I had a letter since locking was not done when the lock part was U-shaped and it did not lock Helmet.
Although it looked good, it was hard to use if it was a single Body more than I thought.
It is scary because Helmet or Motorcycle is nearly scratched if there is no Helmet Anchor of the same Manufacturer.
I think that you are satisfied after purchasing additional Helmet Anchor.
View detail
BABYFACEBabyface Helmet lock
Fast installation. Easy to install. When actually applying Helmet, it may be necessary to some familiarity - - Convenient if there is one. Making is solid. View detail
I attached it to the 16th year MODEL of zx6r.
Performance itself is as expected and is generally satisfying. One thing I was concerned about is that when you attach it with DRing of Helmet, when you remove the key, since Helmet and the keyhole's clearance are few, it is a little hard to work by turning the key. I do not think we can use it, so I do not think there is any problem with Large.
View detail
We purchased Helmet for theft prevention.
- There was no Helmet holder in the car body, I always hung Helmet to the Mirror, but because I became uneasy I bought it for theft prevention.
- When attaching Helmet, it is difficult to attach because it is narrow with Cowl and Holder is in the back!
- expensive
View detail
It was pure, when attached from the beginning, he did not buy an external article and it did not have a key too much, but since it might separate from the time Motorcycle of the grade which is a Touring, the lock perfectly carried out by theft prevention
It was pure, when attached from the beginning, he did not buy an external article and it did not have a key too much, but since it might separate from the time Motorcycle of the grade which is a Touring, the lock perfectly carried out by theft prevention was purchased.Since appearance is settled in such natural touch that it takes that it is pure, it is satisfactory.I think that buyers will also increase in number if
can be carried out and it will be put on the market for about 3000 yen a little at a low price.
View detail
Although the accuracy of the Mount to a main part is good, if the Cylinder of a lock part is made to slide, since there is much blur, it will not enter in many cases.A Mount is touch as a cheap article Chinese-made [ locks / made in Japan and ]. -- si
Although the accuracy of the Mount to a main part is good, if the Cylinder of a lock part is made to slide, since there is much blur, it will not enter in many cases.A Mount is touch as a cheap article Chinese-made [ locks / made in Japan and ].
-- since the attachment Bolt to a main part is unreserved again --
-- A theft is carried out if it is so minded... although there is probably no
choice, there is nothing -- coming out -- the shin.
View detail
If it becomes as easy-to-use as possible since it is hard to use more although the Helmet holder of the KIJIMA was purchased -- Purchase.Although there were the same goods also as the KIJIMA and they strayed, it carried out here somehow in appearance.
If it becomes as easy-to-use as possible since it is hard to use more although the Helmet holder of the KIJIMA was purchased -- Purchase.Although there were the same goods also as the
KIJIMA and they strayed, it carried out here somehow in appearance.Although the Helmet is using XR-1100, it passes along D ring satisfactorily in Size.
user-friendliness is the kana and grade it is [ with dramatically sufficient -- ] better to exist rather than there is nothing although it does not become precocious well.Although it also just said
appearance that it is reasonably priced and a Recommendation was not carried out strongly, it just said that it would not stop if it wants.
Let's keep in mind a Size that it seems that there is incidentally also a Helmet which does not pass along D ring enough.Although I thought that a Site should indicate the
Size essentially, since it was not writing anywhere, it measured by itself. width: -- 23 mm
thickness: -- if it refers to it and gets, taking the hit into consideration since it is the number which the 5mm
amateur measured by the ruler which was in the house.
View detail
[a Webike Monitor] -- the GSX1300R HAYABUSA for the 00 years -- it is riding. it becomes troublesome to remove Cobb each time [ ] and to fix a Helmet -- -- this product was found in the kana ? which is, and the place which was being loo
[a Webike Monitor] -- the GSX1300R HAYABUSA for the
00 years -- it is riding.
it becomes troublesome to remove Cobb each time [
] and to fix a Helmet --
-- this product was found in the kana ? which is, and the place which was being looked for.
If a Carabiner with a key like the
photograph is used, it is convenient at that of
fixable anywhere.
View detail