Reviews
Maybe I don't need Front.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
I thought that the Protector has little protrusion, and since it has a Radiator, I think it is not so meaningful even if it is attached, since it is originally wide.
I hope you don't experience any effects.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
stick out firmly.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
The back seems to stick out and make sense. I hope you don't experience the effect.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
Fits: SUZUKI KATANA, SUZUKI GSX-S1000, SUZUKI GSX-S1000 GT
I'll never roll over …
I'm going to install it with the idea that it will look a little better before it falls down. View detail
Fits: YAMAHA MT-10, YAMAHA YZF-R1, BMW S1000RR, HONDA CBR1000RR, BMW S1000R
Easy detachment!
Rather than a rear slider, the Axle Shaft was installed to make it easier to attach and detach the Axle Shaft.
It can be used as a handle like Doorknob when pulling out shafts, and when inserting shafts, the triangular pyramid shape makes it easy to insert the color, etc. without resistance.
Of course, it would also serve as a Slider, but currently it is benefiting from the detachment process.
View detail
The smallest possible protection without compromising appearance
You won't know performance until you mock it up. View detail
Included Bolt
Please use Stainless Steel for the attached Bolt. View detail
![[IDEAL] Frame Slider](https://img.webike-cdn.net/catalogue/11500/006-sk008_TS.jpg)
Fits: KAWASAKI ZRX1200, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1100
BabyfaceFrame Slider
The same Babyface as Axle Slider was used to create a sense of unity. View detail
Fits: DUCATI 899Panigale, DUCATI 959Panigale, DUCATI 1199Panigale, DUCATI 1299Panigale, DUCATI DIAVEL, DUCATI StreetFighterV2
Simple and inexpensive.
I thought I had researched and ordered it, but the PanigaleV4S was not among the compatible models. Sweat
Item number:006-AD007
The length of the Long Bolt was sufficient, so we cut the transparent tube of the Long Bolt by 1 cm to match the length.
It can only be installed if you have a 10mm deep socket.
I am surprised that neither the product introduction nor the Review mentions SheepSocket.
I went to Astro to buy one.
Single Item:about ?,300, Quantity:It is about 2500 for a set.
View detail
I'm not particularly indebted to you.
I put it on because it's kind of a standard product, but it could have gone either way.
It would be self-satisfying because normal people don't look at these places.
MotorcycleParts, as you might feel if you're also tinkering with cars.
There are a lot of smalls and not as Impact as a car.
For example, Squid Ring.
View detail
I was worried about OEM Engine Guard only, so I bought it.
[How is it used?
In addition to OEM Engine Guard, purchased for Cowl and Tank protection purposes.
Was the one you received as per Image?
Bolt was somewhat dirty and looked new? Bolt was a little dirty and looked like it was new.
I trusted Babyface and am disappointed in that.
Was the installation difficult?
The work itself is easy as it only requires removing and installing the Bolt, but it is better to jack-up the Engine if possible.
Since the Bolt is mounted on the Engine's Frame, I think it will be less burdensome.
Even if you do not jack-up the bolt, be sure to remove the other bolt after the work on the one side of the car body is completed, making sure that the bolt goes straight in.
If the bolt is inserted at an angle, it will damage the cylinder head at worst, so it is better to leave it to a store if you are worried. It is a small amount of work, but it will be a painful experience if you do it improperly.
Torque tightening Torque on Service manual is Quantity:Pair (for Left and Right) Both are 45 N-m.
How was your experience with it?
Since this type is directly attached to the bolt that holds the frame and engine together, there is concern about damage to the frame, but we added it because we thought that together with the OEM engine guard, the pressure and impact would be dispersed to some extent.
If they did not have Engine Guard on, they would not have had this product on either.
[Was there anything that disappointed you?
Bolt was somewhat dirty and thread cutting looked a little crude.
I think the cost performance is good for a slider, but since the bolt is a large bolt directly connected to the frame and engine, I wondered about this.
View detail
Installed on SV650-2022
The bolt that mounts the engine needs to be removed and replaced, so it was necessary to support the engine under the jacketc.
I think it is Merit that the installed state is very simple and you can enjoy the NORMAL stylish feeling, not the element that destroys the appearance of the Motorcycle, but since the slider is directly on the Frame, I am concerned about the effect on the Frame picture when it falls over.
If it is just a standing fall, I think Large is strong enough, but if it falls over, the Slider will be hit strongly from the side with a Large Hammer against the Frame with the whole Engine. Therefore, I am worried that the Frame may be distorted. I don't know how much the Frame will be distorted, but it may be affected if you don't step on it to make it fall slowly even if you are standing on the ground. (That is how it is installed.)
However, since the bolt is replaced with a bolt with both screws for penetrating the Engine and Frame at installation, when one of the screws is bent, if you ride without replacing it and take care of the other side this time, both screws will be bent and the bolt will not be able to pull out. If I do not replace the bolt when one of the screws is bent, I will not be able to replace the Frame Slider and will not be able to return to NORMAL because both screws will be bent and the Bolt will not be able to be pulled out.
If your first priority is to protect the engine and car body, Engine Guard is probably safer.
I was torn between the priority comparison of appearance and guard capability, but I decided to go with the Frame Slider because it is a very stylish motorcycle.
View detail
There is resistance to installation.
The beauty of NAKED is around the bare Engine!
I am wondering when I should remove these parts from the car, as I am not comfortable with them being installed, as they are seriously detracting from the appearance of the car.
View detail
Fits: KAWASAKI ZRX, YAMAHA FZ1, YAMAHA MT-01, YAMAHA YZF-R1, SUZUKI GSX-R1000, KAWASAKI ZRX1200, SUZUKI SV1000, KAWASAKI ZRX1100, APRILIA RS250 (Aprilia), KAWASAKI ZX-12R, KAWASAKI ZRX1200, SUZUKI SV1000, KAWASAKI ZRX1100, APRILIA RS250 (Aprilia), KAWASAKI ZX-12R
insurance
I bought it as an insurance policy. It is not so noticeable, but I don't want to have to deal with it. (Lol) View detail
There are some things that bother me about it:・・・・
AGUSTA, but for the F4 series.
Because Protection around Engine is weak.
(Especially Right Side)
In order to keep the damage to the standing moss to a minimum.
I thought it was essential.
I know Design is a matter of taste, but
With so few mounting surfaces.
I think it's well thought out and...
As for the price, given the number of units sold.
Isn't it neat?
I haven't tried it yet, but...
Now that it's installed, I feel more secure.
But the Spanner latch is not hexagonal.
It's a two-sided pull.
Spanner doesn't fit in some angles.
I would also like to have an OilGasket.
Therefore, from for Left Side
I thought the difficulty level was high.
View detail
Fits: KAWASAKI ZRX1200, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1100
Just in case.
The purpose is to prepare for the standing moss, but there is a custom feeling enough just by installing it. View detail
I am satisfied with the accuracy and appearance of the product ..
This is probably due to the design of the Frame, but the quantity:Pair (for Left and Right) It is not a Penetrating type, so there is some concern about its strength in case of a fall
If it's just a standing mock-up, you'll probably only need to use SliderBody's Damage, but if you're driving If it falls over, there is a possibility that it will break from the Bolt's thinness
However, I chose this product because of its SMART look when installed
View detail
It looks normal
I installed it on the GSX-S1000 (no markings)
It's a Slider with just the right amount of protrusion and a good but not overly assertive feel to it, and it's a Slider that doesn't feel like it's too much of a good thing I think
I can only hope that I won't have to take care of you
View detail
No Cowl cracks
I stood on the Left Side with these Parts, but our Parts are Clutch lever, Side Stand, Footpeg, and Cowl with a degree of splattering I was able to drive myself home with only minor scratches
I'm glad I had it on because I probably would have called the Wrecker if I didn't have it on
I'm not sure if this is the only one that distorts the frame I would like to purchase Engine Guard and install it together with the Plug replacement
View detail
The EngineOil Filler Cap doesn't work!
The texture and sense of security are as expected of BabyFace For installation, it is better to remove part of the cowl It is not in the product description, but as shown in the product photo, the EngineOil Filler Cap You need to replace it with a shorter type because the EngineOil Filler Cap will not open if it is OEM Note that if the EngineOil Filler Cap is OEM, it won't open Please! I didn't realize it until after I installed everything View detail
Design is ○
Design and Cost decide to purchase like.
Bolt head on the generator side was dissatisfied with protruding.
There is no play, so it stops firmly, so it is shallow counterbore?
View detail