Reviews
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA MT03
Requires ingenuity in installation
Model YZF-R25
(8BKRG74) 2022 MODEL
I have prepared the following items to install the brake pedal side.
KITACOAluminum Bracket
BracketWidth:20mm/Thickness:3mm
Hole Size:φ6
Length:60mm
Spacing:40mm
YamahaOEM
Brake fluidReserverHolder
(2015 1WD-F582E-00)
JointZ type bracket with 3 holes
BoltM6×12、M6×15、M6×20
Flange nutM6
Mounting position is set at 60mm back and 40mm up, which is the position with the least interference.
On the shift pedal side, the included shift rod does not fit well, so it will be replaced at a later date.
After the installation, I think it was better to check the position here than to buy expensive Rear Sets and make a mistake. I learned a lot.
View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA MT03
Brake Side
Model YZF-R25
(8BKRG74) 2022 MODEL
Brake Side Image
View detail
Bolt
Bolt supplied with Swing Arm does not fit View detail
I like Large
When it comes to Rear Sets, I have decided to use Babyface for my racing hooks. I have no doubt about the outstanding accuracy, appearance, and functionality. I have installed it on both of my cars. View detail
Babyface for peace of mind
It was installed on R6 with additional cars.
Babyface is good because you can order from Screw1 pc even if Parts are damaged in a fall.
Footpeg has a good bite, so be careful for those who slide and manipulate footpeg.
Shoes must be lifted off the footpeg to move, otherwise the foot may get stuck in the footpeg.
View detail
Body installation itself is easy
Since I bought a used NINJA1000 without a slider, I installed a slider to reduce wounds when falling down.
Removing the cowl is a bit of a hassle, but once removed, it was very easy to install the base plate and the slider cone. However, the M8 Cap Bolt that holds the slider cone in place may loosen easily, so the use of a screw locker is recommended.
It was inexpensive compared to otherManufacturers and the installation diagram in the Instruction Manual was easy to understand.
Two Logo stickers were included.
View detail
as I feared
Product Name
BABYFACE Babyface PerformanceFootpeg Kit
Item Number
002-Y027BK
Vehicles
MT-09 ABS (8BL-RN69J) 2021
Number of man-hours
1 hr. 30 min.
Required Tools
Torque wrench, hexagon socket, Hexagon socket, Extension bar, Combination wrench, -Driver, Hammer, Pliers, etc. would be perfect.
Why did you choose this product?
There are many different Manufacturers at Rear Sets, but I chose Babyface because I knew it would be the best.
Was the one you received as per Image?
The Black paint job is excellent.
Was the installation difficult?
I could manage if I started from the parts I could understand, since there is only an Instruction Manual or a Parts List.
How was your experience with it?
The position has changed a lot, and I have the feeling that it has been customized.
[Included Parts:were they on?
It was an Instruction Manual or a pamphlet or something.
[Was there anything that disappointed you?
High price.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
The finish is beautiful.
I bought this because I don't have a Tandem Footpeg and wanted a place to grab it when using the Roller stand.
The bolt head protrudes from the body and looks bad, so we replaced it with a Titanium bolt with a low head and changed the length of the helmet holder to fit the body.
The material is aluminum, but it is firm enough to be used as an anchor point for tie-downs, and depending on the exhaust bracket, it can also be used on the right side.
It is a good product because the finish is so beautiful that it can be used for dress-up.
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-4R, KAWASAKI ZX-4RR
Happy to reverse shift.
”Reverse Shift is not possible with the Automatic shifter. "Oh, really …" I can't believe that the Reverse Shift, which can be done by changing the Shift arm up and down, is not easy to do! After some research, I found that the Sensor of the Shifter does not respond to the angle at which the Shifter is mounted. I was looking for a footpeg that could be used for Reverse Shift, and I found Babyface, which is compatible with Reverse Shift from several other companies, but I had to buy it as a separate part, and the cost was really low. The feel of the product is solid and very good. I don't feel that it is cheap in any way. The only thing that bothers me a little is that the tips of the Shift and Brake are hard.:I would have preferred Rubber since it is made of Plastic. But don't worry, it won't hurt your feet at all. By the way, the compatible car model is -22 years old, but it can be installed on the latest model 24 years old without any problem. I asked Webig to confirm it for me because I was worried about it. Thank you very much! View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja650, Others , HONDA VTR1000 SP1, HONDA VTR1000 SP2, HONDA VFR800, HONDA VTR250, HONDA RVF400, HONDA VFR750R, HONDA NC700X, HONDA NC750, HONDA GB350S, HONDA NC700S, HONDA CBR1000RR-R SP, HONDA CBR929RR, HONDA CBR1000RR, HONDA CBR1000RR-R, HONDA CBR650R, HONDA CB650F, HONDA CB650R
It is not a pure Black.
The color looks a little brownish rather than black in the right light. It is super easy to install. I think you can install it by yourself, but if you don't have the knowledge to remove the OEM bar end, you might want to ask a shop to do it for you. The included Inner Weight is a few Grams lighter than the OEM. View detail
a titanium anchor
I bought it to wear a Guardian bell I'm afraid it'll rip because it's thin, but trust it because it's titanium! It looks good to mount the bolt anywhere under the bike. View detail
A bit pricey.
With bar ends made entirely of gold, the basic rule is to replace the bar end when it falls over, but in this case, only the resin part can be replaced, so there is no need to buy a new one if it is just a standing bump.
However, the replacement of the resin part is a bit Large strange.
View detail
Fast delivery..good quality
This is a very nice product.
It's the same as the product description.
I think the assembly process would be easier if you attached a photo of the completed assembly, but I'm a little disappointed.
The quality of the product is excellent, delivery is fast and I am very satisfied in many ways..^^
May your business prosper..haha ------------------------------------------------------------ -------------- This is a very nice product. It's the same as the product description. I think the assembly process would be easier if you attached a photo of the completed assembly, but I'm a little disappointed. The quality of the product is excellent, delivery is fast and I am very satisfied in many ways..^^ May your business prosper.. haha Powered by Google Translator
View detail
In case of emergency!
I have just installed it on my other GSXR because I got knocked off my feet on my Harley about 6 months ago. I haven't actually fallen yet, but it is still a good insurance policy. I think it would be better if it had a little more protrusion. The side cowl was a little too large, but Babyface is very accurate and I was able to install it without any problems! View detail
Balance is good!
I found this product because I wanted to refresh the Tandem Footpeg when it was removed. I have no experience with circuits at the moment, so it is just for looks, but it can be used with KIJIMA's helmet holder as well, so I like the way it fits together very nicely. View detail
photographic prints that you can take home with you
With OEM, the footpeg interferes with the footpeg when the foot is lowered, so I purchased this to eliminate this problem with Rear Sets.
There was no instruction manual and it was difficult to install. (Amateur work, about an hour for Small) The position can be adjusted from 4 levels,
Large Variety Satisfaction
View detail
BABYFACERacing hook is the best!
It is one of the ITEMS you must use when you buy a Motorcycle!
Personally, it is as much an iron plate part as the Exhaust System replacement.
The body of the car looks tighter and the color can be matched with the Rear Sets of the same Manufacturer, so that the Rear Sets and Quantity can be matched every time.:It is attached with Set.
This time cbr600rr (2bl-pc40) I installed it with a-tech's Rear brake tank guard and both were great.
View detail
Changed from the same Parts (Black)
[How is it used?
Used for dress-up and in-vehicle use
Was the one you received as per Image?
Street Image
Was the installation difficult?
Easy installation BoltQuantity:2pcs only (for those who have removed Tandem Footpeg)
How was your experience with it?
It has more dress-up elements than practical use, but it is good for one point.
[Included Parts:were they on?
BoltQuantity:2pc
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation Point or hang For those who have removed the Tandem Footpeg/No Instruction Manual/Ease of understanding ◎/Cautions None/Items to be purchased together None/Opinions and requests to the Manufacturer I want Silver anodized color, please!
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-4R, KAWASAKI ZX-4RR
It is easier to put in Neutral when stopped.
The one that makes it easier to get into Neutral, which you'll know when you use it. View detail
incomprehensible
Instruction Manual is too complicated and difficult for beginners. I think some knowledge is necessary. View detail