Reviews
Fits: HONDA MSX125SF, HONDA MSX125, HONDA MSX GROM, HONDA GROM
On the Grom JC92.
I feel that the Pre-road only adjustment is not enough.
The price seems to have gone up quite a bit compared to a while ago.
With this quality, you can get about 12,000 out of it.
Oil damper moves too fast by far when assembled and moved.
Orrifice is too Large in both COMP and TEN.
There are higher-end models with full-length adjustment, but as shown in the photo, the NORMAL and
This is fine for JC-92 as it does not change.
I was going to build it in inverted and lighten it under Spring, but Pre-road.
I gave up before I started messing with it.:If you get a Set, it can be the other way around, but it's pretty good.
I guess I don't care about this level of low-cost products anymore because I will remove parts.
When I first built it with Spring free length, it sank 1/2 of the car body with only 1G.
Finally, the Pre-road comes to the photo.
Originally, sagging was a bit of a hassle since the strokes were extremely short.
Tomorrow I will also tinker with the ZX-14R.
View detail
Fits: HONDA CT125, HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA CROSS CUB, HONDA SUPER CUB110 PRO, HONDA SUPER CUB 50 PRO, HONDA CT125
Shock absorber with limited CROSS CUB50cc compatibility
I was looking for Shock absorber due to OEM fluff, but only Mukawa and Endurance had it as 50cc compatible by Manufacturer.
The damping force can be adjusted to 5 levels, and although I ran the car in the softest state, it felt much stiffer and more firmly planted than the OEM.
Red Nut in the picture is SP Mukawa Rear shock mountNut8 hole Red 06-06-0020
View detail
Fits: HONDA CROSS CUB, HONDA CROSS CUB50, HONDA CT125, HONDA CROSSCUB110, HONDA CT125
improve one's footing
Footing is slightly better.
This makes the Side Stand longer, or the Motorcycle less inclined and unstable, and the Center Stand harder to apply.
Ride quality is better than OEM.
Now we'll see how durable it is
View detail
The security of having your feet on the ground
My wife, who is just under 160cm tall, started riding a CT110 HUNTER CUB, but she is a complete ballerina and has had some bumps and bruises. She was worried about it, so I replaced it with TWRLow seat.
The low seat did not have much effect, but this 40mm Down Suspension worked perfectly, and he was pleased that although his heels floated, the feeling of security was completely different.
As far as my test run is concerned, I think the convergence after the Gap has improved compared to NORMAL. It seemed to converge smoothly and without any lingering aftermath without bouncing around.
However, be careful not to bank too deep, as the Gap during the Corner ring may cause either the Center Stand or the Knee Slider to make contact.
View detail
Fits: HONDA MONKEY BAJA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA
Ideal for protecting engines and drivetrain for both NORMAL and Tuning
Self-produced, LightTuning engine for C100EX (Centrifugal Clutch) and used on a vehicle with a MONKEY suspension combination.
The OEM MONKEY hubs were subject to large stresses and could be damaged, so this product was used.
It is effective for starting, protection of Shift change and acceleration/deceleration Shock, extension of Chain life, reduction of body fatigue, etc.
The damper is rattling after about 7000 km after being used from new, so I personally wish the durability of the damper was higher than 10000 km.... The torque resistance of the threads seems to be a little weak, and when tightened in Overtorque, the threads are likely to be nipped.
Although it is not the perfect product, we are generally satisfied with it because it is a product that can be used for a long period of time, with repair parts available for each part.
View detail
Fits: HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY125, HONDA MONKEY BAJA, HONDA MONKEY125
Rear suspension replacement Parenthesis good!
We felt that the OEM Suspension was a little soft, so we replaced it with SP Mukawa Suspension.
The look and feel has changed from the cute OEM look to a Large person-like look with Chrome plating, which is a nice touch.
However, I was a little disappointed that the edges of the Seal were a little peeled off.
View detail
Fits: HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY125, HONDA MONKEY BAJA, HONDA MONKEY125
Rear suspension replacement Parenthesis good!
The OEM Suspension felt soft, so it was replaced with SP Mukawa's product.
I like the look and feel of it, going from the cute OEM look to a little more Large person with the Chrome plating.
However, it is a little disappointing that the corners of the Seal were a little peeling off.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA Ape50, HONDA CD50, HONDA GORILLA, HONDA CL50, HONDA Ape50, HONDA 12VDAX50, HONDA Ape50, HONDA MONKEY (FI), HONDA MONKEY, HONDA XR100Motard, HONDA XR50Motard, HONDA GORILLA, HONDA Ape50(FI), HONDA Ape50(FI), HONDA Ape100
Black is good!
OEM footpegRubber was torn out and replaced.
I chose this color because I wanted to unify Engine and Frame since they are Black.
Black color was hard to find, so it's expensive, but ……
Perhaps it is my imagination, but the Right Side position is fine, but the Left Side seems to have a bit of a gap.
View detail
Fits: HONDA APE 100, HONDA APE 100 TypeD, HONDA APE 50, HONDA APE TypeD, HONDA APE 50, HONDA XR100MOTARD, HONDA XR50 MOTARD
Since only purchase town riding had carried out here since it was too soft in normal suspension, but higher vehicle adjustment was completed, it was pleased. It was profitable when considering the price, since pre-road adjustment was also possible.
Since only purchase town riding had carried out here since it was too soft in normal suspension, but higher vehicle adjustment was completed, it was pleased.
It was profitable when considering the price, since pre-road adjustment was also possible.
It is not necessarily simply likely to change substantially efficiently.
View detail
Fits: HONDA MONKEY BAJA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA
For improved durability!
My Monkey is 27 years old.
It is about time for various parts to begin to show signs of wear and tear, so we chose this product for our first custom parts in a long time.
This product was purchased with high expectations because of the good reviews in various places.
Installed by myself immediately.
The work itself is Level, which is possible if Tire replacement can be done.
Remove the Chain, remove the Rear wheel, remove the OEM hub, and replace it with this product. Assembly can be done with the supplied tools only.
(I used Torque wrench …...).
It takes about 1.5h from wheel removal to non-building cleanup.
And finally, this week, as testRAN, we go to PetitTwo!
The first thing to do is to start the ride with a very effective Large!
Shock is much less when I put it in first gear from Neutral!
In addition, 2-speed→3-speed→4-speed. Also 4-speed→3-speed→2-speed.
Large width improvement!
And furthermore, even with the Shift change on the pass, the shifting Shocks are gentle!
(It does not mean that Shock is zero.)
We felt that this product would extend the life of Monkey.
I think the price is commensurate with the functionality, but as a small-spender, I personally wish it were a little cheaper.
This product can be recommendation for Monkey riders.
)
View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB110
I am satisfied
I changed the OEM because I was afraid that it would not fit well after the Gap on fast paced national highways and mountain passes. It's a complete change. I'm not sure about the durability yet, but I think the cost performance is high, and I recommend it to people who go touring a lot. View detail
Fits: HONDA MSX125SF, HONDA MSX125, HONDA MSX GROM, HONDA GROM, HONDA GROM
This is a Recommendation.
I bought a new Grom, and as a preliminary information, all the existing users "OEM sass is a free stick." I bought it even before I took delivery of the car because I was REVIEWING it.
OEM suspensions feel like they have to work from 1 to 10 for the input from the road surface, but they only work from 1 to 3, and often the User "Grom's suspension is hard." I'm sorry, but I was under the impression that "The suspension is not responding well to the inputs from the road." This is the impression.
Now, I changed to this Takegawa's rear shock, and I adjusted the pre-road to the lowest setting. The price is only 10,000 yen, but it works much better than the OEM suspension. It works well from 1 to 10 in increments of 1. (If it was a NITRON or OHLINS, it would work in increments of 0.1)
I think it's pretty cosmetic if it's this easy to ride for a little over 10,000 yen investment.
View detail
Fits: HONDA Giorno (4Cycle), HONDA DIO(4Cycle), HONDA SUPER DIO, HONDA TODAY, HONDA TODAY
Good driving stability
Initial model TODAY, but the OEM suspension was the worst in terms of ride quality because it was sticking up and bottoming out on rough surfaces, and it also felt like it was shaking when cornering. By changing to the Takekawa suspension, the bottoming out and thrusting are gone, and the grip of the tires has come out. The sense of security also came out. I think that it will be more comfortable to ride and the stability at high speed will be better.
It's a DIY replacement, but even a beginner can do a DIY replacement if they have some knowledge and tools.
The price is cheap, and I think it is enough from the Motorcycle called TODAY, and I think that it is good to exchange it if I look at the whole though the weakness of the front is conspicuous by exchanging Rear suspension.
View detail
Fits: HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY
Beautiful
When I used 8cm long, the position was upside down with the recommended rear shock length, but when I used 4cm long with the recommended rear shock, the position was proper.
The ease of adjustment of the Chain and the molding of the Adjuster part is very nice.
It would be much better if the Pivot section had a Bearing, Aluminum Collar, etc. (even the Minimoto has one).
Minus 1 star because the surface finish of the rear axle shaft is too gold for this one, and the Axle Nut is removed from the NORMAL for this price.
As for Mukawa's products in general, I'd like them to do QC properly.
I wondered what kind of lordly business they were doing because they were well-established.
View detail
Fits: HONDA MSX125SF, HONDA MSX125, HONDA MSX GROM, HONDA GROM, HONDA GROM
Installed on Custom base's early Grom
Replacement for the OEM BALI Kata GarbageShock.
The shock absorbing capacity has been improved to free you from the pain in your ass.
The cost is good, and if you look for something cheaper than this, you'll find plenty, but I chose this one for the reliability of the Mukawa Brand.
Pre-road adjustment is soft and Quantity:Set。
I don't think I need another set of coilovers.
Disgusting Point
The included Adjusting Wrench is difficult to use.
There is only one Color variation.
View detail
Fits: HONDA APE 100, HONDA APE 100 TypeD, HONDA APE 50, HONDA APE TypeD, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA APE 50, HONDA CBR125R, HONDA MONKEY, HONDA NSF100, HONDA XR100MOTARD, HONDA XR50 MOTARD
Satisfied ideal
The craftsmanship is exquisite, and it is my favorite black color. The small items are also engraved with the brand's Lego. This makes me feel the brand's dedication to each item. Although I have not actually installed and used it, I hope to have Expected effect View detail
Fits: HONDA MSX125SF, HONDA MSX125, HONDA MSX GROM, HONDA GROM, HONDA GROM
Get comfortable with Grom's Rear shock:・・・・
I bought this so that I could adjust my Solidly's Rear shock.
Although it is necessary to remove the Cowl, the replacement itself is easy to do.
However, I think it is a large premise to fix the vehicle so that it does not fall over.
I adjusted it to the lowest setting and it felt a little more grounded.
I'm sure it will feel even better after a while of running and breaking in.
There is a product with dampers, but I am satisfied with this one as cost effective.
View detail
Fits: HONDA MONKEY125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MSX GROM, HONDA MSX125SF, HONDA GROM
I think it is a Large strange work than I thought.
To install, remove the Handlebar→loosen the Fork bolt→loosen the Top bolt→remove the Top bolt from the ROD"replace this Top bolt"with→install→temporarily tighten the Top bolt→ Install Handlebar→Top bolt tighten→Fork bolt tighten→end. The installation itself is not difficult, but it is a tedious job, and the removal from the inner rod was quite Large strange. I did it at the same time as changing Fork Spring. This is the only part that I saw, but it will increase tension. (Lol) Maybe 5 stars if the price was a little lower? View detail
Fits: HONDA MSX125SF, HONDA MSX125, HONDA MSX GROM, HONDA GROM, HONDA GROM
I can't get enough of OEM legs. (Mainly butt pain.) The best of the best costumes for people
Grom OEM's Shock is set up in Tandem, or it's very hard.
That adds to the pain in the buttocks, so we went to the reputable Shock in Mukawa.
Actually, it's got dampers. (06-04-0090) I wanted a
It wasn't registered on webike when I bought it. (Registered since 9/11.)
Required tools are Phillips Screwdriver, 5mm HexaWrench and 10/14/17mm Ratchet.
In order to remove the Shock, you have to remove all the cowls.
The bolts that hold the shocks in place are held in place with a high torque.
The long-handled Ratchet makes the job so much easier.
To adjust, start from the lowest pre-road level and adjust the hardness to your liking.
Mine is 2 pitches loose from the shipping value for good salt.
For a little over 10,000, this suspension is more cosmetic than the OEM's inexplicable feet!
View detail
Fits: HONDA MONKEY BAJA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA
I installed a for MONKEY hub on the DAX
My DAX, when making the front wheels Disc brakeSpec
I used GCraft wheel spacers and Daytona hubs to build it
This time, I decided to use Takegawa hub to match the spec. of the front wheel
I used a GCraft wheel spacer to build the rear wheel
Since the brake is still a Drum, the combination of the Brake Panel of DAX and this hub but
The hub and the Brake Panel interfered with each other and did not rotate smoothly with the bare assembly
So, we adjusted the thickness of the Spacer of 12mm inside diameter to eliminate the interference of the panel
Because the thickness was 8mm, the thickness of the Spacer on the Drive shaft was indicates an area of expertise
We decided to reduce it and maintain the overall width
Also, I'm going to put the Wheel & Tire in reverse from when I was working with the OEM hub
If you don't put it together, the Tire position will be Offset to Left
Please be careful if you want to make the same Spec
Sprocket will also be using for MONKEY, not for DAX
I think it depends on the owner, but for MONKEY, which is lighter in both price and weight, is a better choice to use I think there is a Merit
In terms of weight, the OEM hub + Tire + Wheel weighs 7.1kg
Takegawa hub + GCraftSpacer + Tire + Wheel is 6.8kg the..
We were able to save a small amount of weight
I am very happy with the functionality of this product, but the quantity:1 Set of 3pcs. parts of each
Material feel and finish is RoseRose and not very good looking
It's a bit of a shame, because I think it's an expensive Parts in its own right
View detail