Reviews
Even a custom novice could install it.
I installed this product on a CT125 JA65, and although I am new to customization, I was able to remove the existing frame and install this product without any trouble. Although the Instruction Manual mentioned that there is an upper and lower joint frame, it was difficult for a layman to understand the diagram for distinguishing between the upper and lower frames. It was difficult for a layman to understand the diagram for identifying the top and bottom. I thought that only a person who could read drawings could understand it. Apart from my impression of the product, I was also not impressed that I could finally buy the product more than three months after each Site listing began. View detail
Takegawa Sub Frame Kit installed
The Sub Frame Kit was selected because we wanted to keep the width of the CT125 to the sides of the vehicle, and the volume is slightly increased due to the larger pipe diameter. If you tighten the bolt first, the Under Guard will not be attached. View detail
Unobtrusively Custom
I bought it because I wanted to increase the number of BlackParts as much as possible.
It is also nice to see that the Pipe diameter is slightly larger than OEM.
I was wearing Zita's Under Guard.
The interfering area on the Right Side was shaved off.
View detail
Ideal for Dress-up
This sub-frame enhances the poor BodyFrame and is thicker and more powerful than the OEMPipe diameter of the CT110 HUNTER CUB. The price is high, but I am satisfied with the quality and large size of the product. View detail
stern
The face became tight and stern.
Personally, I'm very happy with it.
One drawback is that the frame part gets in the way when trying to remove the bottom part when changing oil. (This is the position where the Oil is just about to be applied to the Frame.)
It inevitably requires a little effort and a little ingenuity, and I think that is a bit of a hassle.
View detail
I like the thickness.
I wanted to make it look more OEM-like, so I chose this one by Takegawa.
Pipe diameter is larger than OEM, and the difference is obvious compared to OEM.
OEMs look shabby.
I could not feel the rigidity.
The alignment of the holes in the under cover is a bit of a challenge, but if all screws are adjusted with the screws lightly tightened, it can be easily inserted and installed.
View detail
interference
When installing on JA60 YOSHIMURAExhaust System Up Type
Even if the exhaust system can be installed due to interference between the frame and the exhaust system, the blanket of the headlight portion will also be at an angle, so it cannot be installed neatly.
I put Washer in the footpeg position to adjust the height, but it didn't make sense.
If a washer is inserted, the Blanket position in the Headlight section will not be aligned.
The Exhaust System and Frame are always interfering with each other. I am OK with it because I value the appearance.
I would like to see a compatible product.
If you don't want to add Exhaust System Up Type, I can recommend it because it looks great Parenthesis.
It's like the CROSS stock has evolved from a monkey to a GORILLA. (Lol)
View detail
Can also be installed with MORIWAKIShortMONSTER S2 at the same time.
Was the one you received as per Image?
Although the price seems quite high, we choose this Manufacturer for future expandability over similar products.
Quality is, of course, also reliable and high quality.
Was the installation difficult?
First of all, the Exhaust System was replaced with ShortMONSTER S2, so we purchased it after referring to the images of the installed car to see if it could be installed.
I want you to look at the picture of God Clearance.
The installation itself can be done in about 30 minutes if you have the energy to crawl on the ground.
How was your experience with it?
I am more satisfied with the fact that the body looks large than with the engine protection.
However, the bolt is not a part that is finished once it is installed, as it seems to be held in place by a screw, so I think it is necessary to retighten the bolt periodically.
Installation Point or hang
The Corrugated Cardboard that contains the product is used as a matte. (Lol)
View detail
While retaining the OEM design
Recommended for those who do not want to break the OEM Forme, but want to make some changes.
The weight, which is also a concern, is slightly lighter than the OEM, although it is a sturdier design.
The installation accuracy of this product is also high because of the distortion of the body of the car.
No complaints, but one thing, the paint is sweet, it is thin.
During installation, a slight drop on the Asphalt will scratch the paint.
How about this?
Can't you make the paint film a little thicker?
I painted the wound with Magic.
It's really just because everything else is so good. Nice try."
When installing on the car body, all screws must be temporarily attached to the car body.
Retightening!
The body of the vehicle is distorted, so time is wasted on installation.
View detail
Black Match the vehicle
Stiff but relatively lightweight, with a casual dress-up look. View detail
I like the zushiri feeling.
I like the way it looks.
Rigidity? I am not sure about the
View detail
Just remove the Headlight and you're good to go!
Black in stock is undecided about the delivery date, so the color in stock is:Buy Yellow.
I painted it in the same OD color as the car body color and installed it.
From the other reviews, it seems that the Bracket is installed in a large size, so I was prepared for the challenge (lol).
When I looked at the Takekawa Instruction Manual, it said that I needed to remove a lot of parts to install the Bracket, but I thought I could get away with just the Headlight. I thought I could get away with just removing the Headlight, inserting the Bracket, and putting the Headlight back on.
Do not use Bracket's supplied mounting Cap bolt, use Stainless SteelHexagon Bolt at Home center and tighten with Ratchet TypeGlassesSpanner.
There was nothing difficult or Large strange about it.
If you're going to put it on, you'll need to purchase a Ratchet glasses wrench and a Bolt. ・・・・
I'm going to remove the Skid plate and RightFrame and take it to a Motorcycle shop as it interferes with the removal of the Drain bolt when changing the Oil.
View detail
Good looking Balance.
I went for a Red body with a Black Sub-frame.
I had a Motorcycle shop install it when I took delivery of the car, but from the looks of it, it shouldn't be too difficult!
The pipe diameter is thicker than OEM, which improves the appearance of balance.
The texture and construction of the paint is also good, so I think it is a highly satisfactory product
If you install the Fog Lamp Kit, it will be a custom Trekking style, and it will also be a solution for the dark headlight.
View detail