Reviews
Aluminum Pipe is looking sharp.
I bought a long aluminum pipe for my own parts for CRF250RALLY. I used to cut it with an iron saw, but I think it is better to use SK11's Pipe cutter for clean cutting.
After deciding the length to be cut, use the Magic to mark a point on the Pipe cutter, place the round blade of the Pipe cutter on the point, and lightly tighten the Grip. When the markings are visible, turn the Pipe cutter further. You will feel resistance when you turn it, but when it becomes weaker, the amount of turning will be cut. If you continue to rotate the Pipe cutter, the Pipe cutter will make a horizontal gap, so you will need to increase the depth of the cut by pulling out the round blade further. After cutting, pull out the chamfering blade attached to the body to chamfer the inside of the pipe.
When determining the length of the cut, it is better to make adjustments by considering the thickness of the blade. In the case of an iron saw, the object is cut off with the tip of the blade on a line Image, but with a round blade, Quantity:Pair (for Left and Right) The body has a roller to hold the pipe in place. The body has a roller to hold the pipe in place. If the object is soft aluminum, the roller will leave marks if it is tightened too hard. If the holder of the round blade starts to wobble during use, which is rare, remove the grip cover and tighten the loose screws. The first marking is easy with aluminum, but difficult with steel, and be careful with plating pipe, which is slippery even after marking. The chamfering after the work is simple. The final chamfering should be done with sandpaper or a file or you will get hurt.
This tool is designed for Pipe, but I also use it for cutting and marking aluminum rods with an iron saw. The process is the same, but there is a limit to how far a round blade can cut a round bar. If the marking is on a line, it is easier to apply the cutting edge of the iron saw and fix it in place. In this case, the length of the cut is adjusted with a margin for the tip of the blade.
If you are a beginner, it is difficult to cut a round Pipe cleanly with an iron saw. It depends on the work environment, but it is a good tool to have.
View detail
Exchange for Refresh
I bought a used ZZr, a motorcycle that probably hasn't had its suspension linkage greased in 26 years.
It can be used normally, but the cap seems to come off easily.
View detail
For the Left Hand. You can beat the hell out of anything zakzaky!
For Left Handers. The Elastomer resin Grip is a good choice! Elastomer resin grips for non-slip grip!
NeedlesGold, Copper wire, Tin plate, Aluminum, Cardboard, Cloth, PPBandetc.Basically anything I can hit it off." is the appeal of this product.
Blades are rust-resistant Material:I'm glad it's Stainless Steel, it's a Commendation!
View detail
For cleaning complex shapes around the Engine
Engine fins and switches in the Handlebar.
Purchased to clean crevices in complex shapes.
I do this about twice a year, just to clean up all the little details.
Long cotton swabs are used in the gaps between Engine fans, Switches, etc.
It removes dirt and grime from even the most complex shapes.
This is convenient and useful.
View detail
It cuts well.
It is easy to grip and cuts well, so you can cut with light force.
Ideal for cutting thick corrugated balls that are difficult to cut with regular Scissors.
Good durable scissors.
View detail
Well material
The moderate spring feeling makes it easy to use and does not grab the fingers. The shape is also comfortable to hold, making it easy to work with.
The angle of the tip is good enough to keep the gripped object without dropping it.
It is Stainless Steel, so it can be used for a long time.
View detail
be sharp
These scissors cut well. Suitable for putting on small parts.
Material:Stainless steel makes these precision gold cutting scissors very sharp and resistant to rust.
Easy to cut with light force.
View detail
Good
I used it to protect the cargo in the back of my light truck from rain, Dust, etc.
Elastic bands can be used to secure it to the body of the vehicle, so it will not turn up while driving and will protect the well luggage.
The fabric is thick, so it is durable and can be used for a long time.
View detail
Durable
This is to prevent damage to the cargo bed of a light truck.
The thicker rubber helps prevent scratches on the Floor and also prevents slipping.
It is good because it does not flap while running unlike the PeLePera ones.
View detail
be sharp
Carpet cuts well.
With Cutter, you need an underlay, but with Scissors, you can cut it quickly and conveniently.
View detail
good
I used it for about 3 years, though I threw it away the other day. It was sharp. View detail
peeling off
I bought it last time to try it out and was using it, but the tip became uneven due to overworked use, so I bought Repeat.
Reasonably priced, moderate elasticity, taper tip, just right for removing dirt in areas where you don't want to scratch.
View detail
HandlebarCut
I bought this to make the Pro taper HandlebarSEVEN EIGHTH wide enough for me. I was worried that it might become a gap while turning round and round, but it is easy to the extent that I was out of step because it was able to cut easily and beautifully. Because BALI comes out as for the cutting surface, File is applied lightly, and completion.
If you want to adjust the width with a Pipe Handlebar, it's a good thing to have.
View detail
You can Cut the Handlebar cleanly.
When replacing the Handlebar, the Quantity:Pair (for Left and Right) I bought this to Cut both ends to my preferred length.
To use, simply align the teeth with the position you want to cut on the Handlebar, pinch it, and turn it around.
Naturally, as the cut is made, a gap is created, so it is hang to rotate this Tool while constantly adjusting it to press the teeth firmly.
At first, I used the same tension and rotated it for a while, but it didn't cut very well, and then I realized that I could easily cut it by tightening it a little bit and using it to rotate.
In the meantime, I sprayed it with Kure 556 to lubricate it.
The tool that can be sanded a little after cutting is also Quantity:If you want to adjust the Size of the Handlebar to your liking, it's not an expensive tool, so it's good to have one.
View detail
I don't want you to get hurt.
I was looking for something plastic, somewhat strong, and resilient so as not to scratch the inside of the Cowl to remove stains such as oil and chain stains, and I bought this one to try.
The delivery time took a little, but the price is cheap, and JAPAN, it is also good for use. Next time, I would like to buy it again in reserve, replenishment.
View detail
A must for Garage
I put a workbench in my Garage and I wanted to fix things in place and process them, so I installed this Vise If it is the work of motorcycle, it works well enough with this much Vise Because it is possible to burn with Burner, it is very useful to fix the bent Lever I am! View detail
Cleaning the Throttle Body
I found it in the home center and searched to see if they sold it in We-Big, and they did!
I used to clean it by wrapping Dustcloth around a splitter's beak, but this way, the tip of the Small scale production
It is easy to insert into the Throttle Body for a good view inside and easy cleaning
I cleaned the two cylinders and the cotton didn't fall apart
View detail
I am satisfied.. I should have bought it sooner.
I purchased Compressor for my first home Garage. Various Manufacturer, I was lost as to the model, but the desired performance can be used with 100v for home use. Being silent. Things that have horsepower. If Air raises it, there will be no tightness and eventually sk 11 It was to.
First, the sound is quite quiet. As it is easy to say, it is about idling car of NORMAL so I use it even in the middle of the night. I was satisfied with Large because I was prepared for the sound of a stall generator. Horsepower is also 1. Because it is 5 hp, it is also fast for Air to accumulate. About 2-3 minutes.
What I was concerned about before purchasing is power consumption. According to the Instruction Manual of ManufacturerSite, 1200 w at the time of reboot was 2 to 3 times as much power as I had, so I was worried that 20 A outletlet for home use would fall.
No problem. I also restart firmly.
Large satisfaction with Large. I wish I could buy it sooner. As soon as I bought it, I switched Seat with Air Tucker and replaced the Studless Tire with Impact wrench.
If you have a Compressor you can do that too and your dream will spread. Is it difficult to say, it is a non-stop, but I wanted a Sub tank.
View detail